Pipeline and Hazardous Materials Safety Administration May 2006 – Federal Register Recent Federal Regulation Documents

Dominion Transmission, Inc. (DTI) requested a waiver of compliance from requirements for pipelines constructed after March 31, 2000. This waiver will allow DTI to use the most recent, 2006 National Fire Protection Association's (NFPA) 59A, ``Standard for Production, Storage, and Handling of Liquefied Natural Gas'' and comply with PHMSA's liquefied natural gas (LNG) facility safety regulations.

This notice is to advise interested persons that PHMSA will conduct a public meeting in preparation for the 29th session of the United Nation's Sub-Committee of Experts on the Transport of Dangerous Goods (UNSCOE) to be held 3-12 (a.m.) July 2006 in Geneva, Switzerland.

In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR part 107, subpart B), notice is hereby given that the Office of Hazardous Materials Safety has received the application described herein. Each mode of transportation for which a particular special permit is requested is indicated by a number in the ``Nature of Application'' portion of the table below as follows: 1Motor vehicle, 2Rail freight, 3Cargo vessel, 4Cargo aircraft only, 5Passenger-carrying aircraft.

On May 1, 2006, PHMSA published a safety advisory notice advising the public that certain high pressure DOT exemption cylinders were not tested in accordance with applicable regulatory requirements. In the safety advisory notice, the serial numbers for the Goodrich cylinders ``Model No. T123-1 GOODR'' were listed incorrectly. This safety advisory notice corrects the May 1, 2006 safety advisory notice to provide the correct serial numbers for the affected cylinders. PHMSA published the safety advisory after learning of the manufacture, marking, and sale of certain high pressure DOT exemption cylinders that were not tested in accordance with applicable regulatory requirements. These cylinders were manufactured and/or distributed by Luxfer, Inc. (Luxfer), Riverside, CA. Luxfer and its independent inspection agency, Arrowhead Industrial Services, Inc. (Arrowhead), reported to PHMSA that 6,325 high pressure cylinders manufactured to the DOT CFFC and FRP-1 standards as authorized in DOT-E 10915, DOT-E 9634, and DOT-E 9894, had been shipped from Luxfer without undergoing the required autofrettage and hydrostatic tests. In a joint effort, Luxfer and Arrowhead have retrieved 2,581 of the untested cylinders. The model numbers and serial numbers of the remaining 3,859 cylinders are listed in this notice. Only cylinders with the listed serial numbers listed are affected. A person with a listed cylinder should discontinue use of the cylinder and return it to Arrowhead at the address below so the autofrettage and hydrostatic test can be completed before its next use. Shippers and compressed gas filling facilities are advised that these cylinders do not meet the requirements of the Hazardous Materials Regulations and may not be offered for transportation or transported until the required testing is completed.

PHMSA was recently notified of the manufacture, marking, and sale of certain high pressure DOT exemption cylinders that were not tested in accordance with applicable regulatory requirements. These cylinders were manufactured and/or distributed by Luxfer, Inc. (Luxfer), Riverside, CA. Luxfer and its independent inspection agency, Arrowhead Industrial Services, Inc. (Arrowhead), reported to PHMSA that 6,325 high pressure cylinders manufactured to the DOT CFFC and FRP-1 standards as authorized in DOT-E 10915, DOT-E 9634, and DOT-E 9894, had been shipped from Luxfer without undergoing the required autofrettage and hydrostatic tests. In a joint effort, Luxfer and Arrowhead have retrieved 2,581 of the untested cylinders. The model numbers and serial numbers of the remaining 3,744 cylinders are listed in this notice. Only cylinders with the listed serial numbers listed are affected. A person with a listed cylinder should discontinue use of the cylinder and return it to Arrowhead at the address below so the autofrettage and hydrostatic test can be completed before its next use. Shippers and compressed gas filling facilities are advised that these cylinders do not meet the requirements of the Hazardous Materials Regulations and may not be offered for transportation or transported until the required testing is completed.