Federal Aviation Administration 2021 – Federal Register Recent Federal Regulation Documents
Results 501 - 550 of 1,565
Airworthiness Directives; Bombardier, Inc. Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes. This proposed AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Austro Engine GmbH Engines
The FAA proposes to supersede Airworthiness Directive (AD) 2021-09-04, which applies to all Austro Engine GmbH E4 and E4P model diesel piston engines. AD 2021-09-04 requires replacing a certain oil pump as well as the oil filter and engine oil. Since the FAA issued AD 2021-09-04, the FAA determined that the requirement to replace the oil pump should be limited to only Austro Engine E4 and E4P model diesel piston engines with a certain oil pump, identified by part number (P/N) and serial number (S/N), installed. This proposed AD would require replacing a certain oil pump, the oil filter, and the engine oil installed on Austro Engine GmbH E4 and E4P model diesel piston engines. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters Deutschland GmbH Helicopters
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Helicopters Deutschland GmbH Model MBB-BK 117 D-2 helicopters. This proposed AD was prompted by a report of chafing marks on a wiring harness near the locking washer of the lateral control rod. This proposed AD would require an inspection of the wiring harness and the routing of the wiring harness and corrective actions if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Bell Textron Canada Limited Helicopters
The FAA proposes to supersede Airworthiness Directive (AD) 2021-06-06, which applies to certain Bell Textron Canada Limited Model 505 helicopters. AD 2021-06-06 requires repetitive fluorescent penetrant inspections (FPIs) of the pilot collective stick and grip assembly and revising the existing Rotorcraft Flight Manual (RFM) for your helicopter. Since the FAA issued AD 2021-06-06, the pilot collective stick and grip assembly has been redesigned. This proposed AD would retain certain requirements of AD 2021-06-06, require modifying your helicopter to include the improved pilot collective stick tube and would add a terminating action for the repetitive FPIs. This proposed AD would also prohibit installing any pilot collective stick and grip assembly unless certain requirements of this proposed AD were met. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is revising an earlier proposal for certain Leonardo S.p.a. Model AB139 and AW139 helicopters. This action revises the notice of proposed rulemaking (NPRM) by expanding the required actions. This proposed AD would require various inspections of certain main rotor (MR) dampers, as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is proposed for incorporation by reference (IBR). This proposed AD would also require reducing the torque of the MR damper hub attachment bolts, installing a special washer, installing a certain part-numbered MR damper, and prohibit installing other part-numbered MR dampers. The FAA is proposing this airworthiness directive (AD) to address the unsafe condition on these products. Since these actions would impose an additional burden over those in the NPRM, the FAA is requesting comments on this SNPRM.
Airworthiness Directives; Daher Aerospace (Type Certificate Previously Held by SOCATA) Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Daher Aerospace (type certificate previously held by SOCATA) Model TBM 700 airplanes. This proposed AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a non-conforming dump switch ejecting from its slot. This proposed AD would require modifying certain dump switches. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Bell Textron Canada Limited
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bell Textron Canada Limited Model 206, 206A, 206A-1, 206B, 206B-1, 206L, 206L-1, 206L-3, and 206L-4 helicopters. This proposed AD was prompted by reports of cracked or missing nuts on the tail rotor drive shaft (TRDS) disc pack (Thomas) couplings. This proposed AD would require removing certain nuts from service, installing newly designed nuts, and applying a specific torque and a torque stripe to each newly installed nut. This proposed AD would then require, after the installation of each newly designed nut, inspecting the torque and, depending on the inspection results, either applying a torque stripe or performing further inspections and removing certain parts from service. Finally, this proposed AD would prohibit installing any affected nut on any TRDS Thomas coupling. The FAA is proposing this AD to address the unsafe condition on these products.
Petition for Exemption; Summary of Petition Received; Jenks Family Farms
This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, FAA's exemption process. Neither publication of this notice nor the inclusion nor omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Petition for Exemption; Summary of Petition Received; FedEx Corporation
This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion nor omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Petition for Exemption; Summary of Petition Received; ABC Drones, LLC
This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion nor omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Amendment of Class E Airspace; Courtland, AL
This action amends Class E airspace extending upward from 700 feet above the surface for Courtland Airport, Courtland, AL, by amending the name and geographical coordinates of Courtland Airport (formerly Industrial Airpark Airport).
Revocation of Class E Airspace and Amendment of Class E Airspace; Peebles and West Union, OH
This action revokes the Class E extending upward from 700 feet above the surface at Peebles, OH; and amends the Class E airspace extending upward from 700 feet above the surface at Alexander Salamon Airport, West Union, OH. This action is the result of airspace reviews caused by the decommissioning of the West Union non-federal non- directional beacon (NDB). The geographic coordinates of the Alexander Salamon Airport are also being updated to coincide with the FAA's aeronautical database.
Proposed Amendment Class E Airspace and Establishment of Class E; Greenville and Terrell, TX
This action proposes to amend the Class E airspace at Greenville, TX, and establish Class E airspace at Terrell, TX. The FAA is proposing this action as the result of airspace reviews due to the decommissioning of the Caddo Mills non-directional beacon (NDB). The geographic coordinates of Caddo Mills Municipal Airport, Caddo Mill, TX, would also be updated to coincide with the FAA's aeronautical database.
Airworthiness Directives; International Aero Engines, LLC Turbofan Engines
The FAA is adopting a new airworthiness directive (AD) for certain International Aero Engines, LLC (IAE) PW1122G-JM, PW1124G1-JM, PW1124G-JM, PW1127G1-JM, PW1127GA-JM, PW1127G-JM, PW1129G-JM, PW1130G- JM, PW1133GA-JM, and PW1133G-JM model turbofan engines. This AD was prompted by a root cause analysis of an event involving an uncontained failure of a high-pressure turbine (HPT) disk that resulted in high- energy debris penetrating the engine cowling on an Airbus Model A321- 231 airplane, powered by IAE V2533-A5 model turbofan engines. This AD requires removing certain HPT 1st-stage and HPT 2nd-stage disks from service. The FAA is issuing this AD to address the unsafe condition on these products.
Petition for Exemption; Summary of Petition Received; Alitalia Societa Aerea Italiana
This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Petition for Exemption; Summary of Petition Received; Choose Aerospace, Inc.
This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion nor omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
IFR Altitudes; Miscellaneous Amendments
This amendment adopts miscellaneous amendments to the required IFR (instrument flight rules) altitudes and changeover points for certain Federal airways, jet routes, or direct routes for which a minimum or maximum en route authorized IFR altitude is prescribed. This regulatory action is needed because of changes occurring in the National Airspace System. These changes are designed to provide for the safe and efficient use of the navigable airspace under instrument conditions in the affected areas.
Proposed Revocation of United States Area Navigation Routes Q-162 and Q-166; Bishop, CA
This action proposes to revoke United States Area Navigation (RNAV) routes Q-162 and Q-166 in the vicinity of Bishop, CA due to the establishment of a new RNAV route, Q-174, that provides better connectivity for the Las Vegas Terminal area arrivals.
Amendment of Class E Airspace; Monroe, NC
This action amends Class E airspace extending upward from 700 feet above the surface for Charlotte-Monroe Executive Airport, Monroe, NC. The FAA is taking this action as a result of the Charlotte Class B Biennial Review. This action also updates the airport's name to Charlotte-Monroe Executive Airport (formerly Monroe Airport). In addition, this action updates the geographic coordinates of the airport to coincide with the FAA's database. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations in the area.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2020-21-17, which applies to all The Boeing Company Model 757 airplanes. AD 2020-21-17 requires repetitive inspections for skin cracking and shim migration at the upper link drag fittings, diagonal brace cracking, and fastener looseness; and applicable on-condition actions. Since the FAA issued AD 2020-21-17, a determination has been made that the compliance times for certain groups are not adequate. This proposed AD would retain the requirements of AD 2020-21-17 with reduced compliance times for certain airplane groups. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Gulfstream Aerospace LP Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace LP Model Gulfstream G280 airplanes. This AD was prompted by a report that during full-scale fatigue testing, a crack was found in the area of the attachment of the wing rib 0 to the front spar. This AD requires non-destructive testing on the forward (front) spar vertical stiffener and rib 0 for any cracking, installation of a doubler to the forward (front) spar and rib 0 attachment, and repair if necessary, as specified in a Civil Aviation Authority of Israel (CAAI) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is withdrawing a notice of proposed rulemaking (NPRM) that proposed to adopt a new airworthiness directive (AD) that would have applied to certain The Boeing Company Model 787-8, 787-9, and 787- 10 airplanes. The NPRM was prompted by reports that very high frequency (VHF) radio frequencies transfer between the active and standby windows of the tuning control panel (TCP) without flightcrew input. The NPRM would have required updating the TCP operational software (OPS) and performing a software configuration check. Since issuance of the NPRM, the FAA determined that the TCP OPS version specified in the NPRM does not correct the unsafe condition. The FAA intends to propose new rulemaking to require updated software. Accordingly, the NPRM is withdrawn.
Proposed Amendment of United States Area Navigation Route Q-73 in the Vicinity of Twentynine Palms, CA
This action proposes to amend United States Area Navigation (RNAV) route Q-73 due to the creation of Special Activity Airspace (SAA) (Bristol Air Traffic Control Assigned Airspace (ATCAA)) in the vicinity of Twentynine Palms, CA.
Airworthiness Directives; Embraer S.A. (Type Certificate Previously Held by Empresa Brasileira de Aeronáutica S.A.) Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2020-12-08, which applies to all Embraer S.A. Model EMB-505 airplanes. AD 2020-12-08 requires inspections of the mass-balance weights of the elevators, ailerons, and rudder (flight control surfaces) and their attachment parts, and corrective actions if necessary, and revising the airworthiness limitation section of the maintenance manual or instructions for continued airworthiness to incorporate new airworthiness limitations. Since AD 2020-12-08 was issued, the FAA has determined that new applicable airplane serial numbers and new criteria for the replacement of affected parts must be required in order to address the unsafe condition. This proposed AD would retain the actions required by AD 2020-12-08 and would require, for certain airplanes, cleaning and weighing certain mass-balances and installation or replacement, as applicable; and for certain other mass-balances for certain airplanes, replacement of those mass-balances. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; B-N Group Ltd. Airplanes
The FAA is adopting a new airworthiness directive (AD) for B-N Group Ltd. Models BN-2, BN-2A, BN-2A-2, BN-2A-3, BN-2A-6, BN-2A-8, BN- 2A-9, BN-2A-20, BN-2A-21, BN-2A-26, BN-2A-27, BN-2B-20, BN-2B-21, BN- 2B-26, BN-2B-27, BN-2T, and BN-2T-4R airplanes. This AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI identifies the unsafe condition as failure of the rudder final drive rod because of cracks in the region of the taper pins. This AD requires repetitively inspecting the rudder final drive rod assembly and replacing the rudder final drive assembly, if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Revocation of Class E Airspace; Port Huron, MI
This action revokes the Class E surface airspace at St. Clair County International Airport, Port Huron, MI. This action is the result of an airspace review caused by the decommissioning of the Remote Communications Outlet (RCO) frequency at St. Clair County International Airport.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Training and Qualification Requirements for Check Airmen and Flight Instructors
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The collection involves the reporting requirements to ensure the check pilots and instructors are adequately trained and checked/evaluated to ensure they are capable and competent to perform the duties and responsibilities required by the air carrier to meet the regulations. Experienced pilots who would otherwise qualify as flight instructors or check airmen, but who may not medically eligible to hold the requisite medical certificate are mandated to keep records that may be inspected by the FAA to certify eligibility to perform flight instructor or check airmen functions.
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG (Type Certificate Previously Held by Rolls-Royce plc) Turbofan Engines
The FAA is superseding Airworthiness Directive (AD) 2020-13-07 for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Trent 1000-D2, Trent 1000-J2, and Trent 1000-K2 model turbofan engines with a certain part- numbered fuel pump installed. AD 2020-13-07 required removal and replacement of the fuel pump with a part eligible for installation. This AD was prompted by the manufacturer's investigation into an unexpected reduction in fuel pump performance in certain high life fuel pumps and subsequent determination that an additional part-numbered fuel pump is subject to the same unsafe condition. This AD requires new and reduced life limits for certain part-numbered fuel pumps, depending on the engine model the fuel pump is installed on. The FAA is issuing this AD to address the unsafe condition on these products.
Amendment of Class E Airspace; Scott City, KS
This action amends the Class E airspace extending upward from 700 feet above the surface at Scott City Municipal Airport, Scott City, KS. This action is the result of an airspace review due to the decommissioning of the Scott City non-directional beacon (NDB). The geographical coordinates of the airport are also updated to coincide with the FAA's aeronautical database.
Amendment of Class E Airspace; Sac City, IA
This action amends the Class E airspace extending upward from 700 feet above the surface at Sac City Municipal Airport, Sac City, IA. This action is the result of an airspace review caused by the decommissioning of the Sac City non-directional beacon (NDB).
Revocation of Class E Airspace; Standish, MI
This action revokes the Class E airspace extending upward from 700 feet above the surface at Standish Industrial Airport, Standish, MI. This action is the result of an airspace review caused by the closing of the Standish Industrial Airport and associated instrument procedures are no longer required.
Amendment of Class E Airspace; Yoakum, TX
This action amends the Class E airspace extending upward from 700 feet above the surface at Yoakum Municipal Airport, Yoakum, TX. The FAA is proposing this action as the result of an airspace review caused by the decommissioning of the Yoakum non-directional beacon (NDB).
Amendment Class D and Class E Airspace; South Florida
This action amends Class D and Class E airspace in the south Florida area, by updating the geographic coordinates of the following airports; Fort Lauderdale-Hollywood International Airport, Miami-Opa Locka Executive Airport, (formerly Opa Locka Airport), North Perry Airport, Pompano Beach Airpark, Miami International Airport, Homestead ARB, Boca Raton Airport, and Miami Executive Airport (formerly Kendall- Tamiami Executive Airport). This action also updates the geographic coordinates of the Fort Lauderdale Very High Frequency Omnidirectional Range collocated with Distance Measuring Equipment (VOR/DME), and the QEEZY Locator Outer Marker (LOM). Furthermore, this action makes an editorial change replacing the term Airport/Facility Directory with the term Chart Supplement in the legal descriptions of associated Class D and E airspace. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) in the area.
Airworthiness Directives; Leonardo S.p.a Helicopters
The FAA proposes to adopt a new airworthiness directive (AD) for certain Leonardo S.p.a. (Leonardo) Model AW109SP helicopters. This proposed AD was prompted by reports of an ineligible hydraulic pump being installed on Model AW109SP helicopters. This proposed AD would require inspecting each hydraulic pump for damage and, depending on the inspections results, removing parts from service and accomplishing other corrective actions. This proposed AD would also require removing certain parts from service before they exceed their life limits. The proposed corrective actions would be required to be accomplished as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters Deutschland GmbH (AHD) Helicopters
The FAA is adopting a new airworthiness directive (AD) for Airbus Helicopters Deutschland GmbH (AHD) Model MBB-BK 117 D-2 helicopters. This AD was prompted by the discovery that certain parts that are approved for installation on multiple helicopter models are life limited parts when installed on Model MBB-BK 117 D-2 helicopters and some helicopter delivery documents excluded the life limit information. This AD requires determining the total hours time-in- service (TIS) of a certain part-numbered rotor mast nut and re- identifying a certain part-numbered rotor mast nut. This AD also requires establishing a life limit for a certain part-numbered rotor mast nut and helical gear support, and removing each part from service before reaching its life limit. Additionally, this AD requires replacing a certain part-numbered main gearbox (MGB) with a not affected MGB as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, and AS350D helicopters; and Model AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters. This AD was prompted by reports that the lanyards (bead chain tethers), which hold the quick release pins to the forward bracket assembly of certain litter kits, can loop around the directional control pedal stubs, limiting the movement of the pedals. This AD requires modification of the lanyard attachment location for certain litter kit installations. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Bell Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited Model 505 helicopters. This AD was prompted by three occurrences of metallic debris in the engine oil lubrication system causing the 12 volts direct current (VDC) reference voltage to be shorted to ground and loss of important flight information to the pilot. This AD requires replacing a certain part- numbered relay panel assembly. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters Deutschland GmbH Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Deutschland GmbH Model EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, and EC135T3 helicopters. This AD was prompted by a report that geometrical non-conformities were found in the root section of the tail rotor blade (TRB). This AD requires a one-time inspection (dimensional check) of the TRB for conformity and, depending on the findings, replacement of certain affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits rework, repair, or modification of affected parts in the affected area of the TRB assembly root. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a. Model AW189 helicopters. This AD was prompted by corrosion on the inlet check valve banjo fitting of emergency flotation system (EFS) float assemblies. This AD requires visually inspecting each banjo fitting installed on an affected EFS float assembly, and depending on the results, removing the banjo fitting from service. This AD also requires applying corrosion inhibiting compound and prohibits installing an affected EFS float assembly unless certain requirements have been accomplished as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model AB412 and AB412 EP helicopters. This AD was prompted by a report of the failure of both inverters in-flight, leading to an autopilot disconnection. This AD requires a one-time inspection of the clearance between a certain protective grommet installed in the emergency bus interlock compartment and the cable assemblies passing through it, and depending on the finding, applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters
The FAA is superseding Airworthiness Directive (AD) 2016-12- 51, which applied to all Airbus Helicopters Model AS332L2 and Model EC225LP helicopters. AD 2016-12-51 prohibited all further flight of Model AS332L2 and Model EC225LP helicopters. This AD requires replacing certain second stage planet gear assemblies, removing certain epicyclic modules, installing a full flow magnetic plug (FFMP), revising the existing rotorcraft flight manual (RFM) for your helicopter, repetitively inspecting the main gearbox (MGB) particle detectors, repetitively inspecting the MGB oil filter and oil cooler, and corrective action if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The actions specified in this AD terminate the flight prohibition. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Bell Textron Canada Limited Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited Model 206, 206A, 206A-1 (OH-58A), 206B, 206B-1, 206L, 206L-1, 206L-3, 206L-4, 222, 222B, 222U, 230, 407, 427, 429, and 430 helicopters. This AD was prompted by a report of a shoulder harness seat belt comfort clip (comfort clip) interfering with the seat belt inertia reel. This AD requires removing each comfort clip from service, inspecting the shoulder harness seat belt for any rip and abrasion, and removing any shoulder harness seat belt from service that has a rip or abrasion. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Leonardo S.p.a. Helicopters
The FAA is adopting a new airworthiness directive (AD) for Leonardo S.p.a. Model AB139 and AW139 helicopters with certain main rotor blades installed. This AD was prompted by a report of an in- flight loss of a main rotor blade (MRB) tip cap. This AD requires inspecting the MRB tip cap for disbonding. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Bombardier, Inc., Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2017-22-06, which applies to certain Bombardier, Inc., Model CL-600- 2B16 (601-3A, 601-3R, and 604 Variants) airplanes. AD 2017-22-06 requires repetitive inspections for fuel leakage at the engine and auxiliary power unit (APU) fuel pumps, and related investigative and corrective actions if necessary. Since the FAA issued AD 2017-22-06, terminating actions have been developed and additional airplanes have been determined to be affected by the unsafe condition. This proposed AD would retain the requirements of AD 2017-22-06, and require an inspection of the APU, repair if necessary, and modification of the engine electrical fuel pump (EFP) installation. This proposed AD would also add airplanes to the applicability. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Robinson Helicopter Company Helicopters
The FAA is adopting a new airworthiness directive (AD) for certain Robinson Helicopter Company Model R44 and R44 II helicopters. This AD was prompted by reports of cracked tail rotor blades (blades). This AD requires checking each blade for any crack and removing any cracked blade from service. This AD also requires removing all affected blades from service and prohibits installing any affected blade on any helicopter. The FAA is issuing this AD to address the unsafe condition on these products.
Agency Information Collection Activities: Request for Comments; Clearance of a New Approval of Information Collection: Formal Complaints Collection
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments within 30 days after the date of publication of this notice about its intention to request the Office of Management and Budget (OMB) approval for an existing information collection. This collection involves the filing of a complaint with the FAA alleging a violation of any requirement, rule, regulation, or order issued under certain statutes within the jurisdiction of the FAA. The FAA will use the information collected to determine if the alleged violation warrants investigation or action. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on August 4, 2020.
Airworthiness Directives; Airbus SAS Airplanes
The FAA is correcting an airworthiness directive (AD) that was published in the Federal Register. That AD applies to certain Airbus SAS Model A318-111, -112, and -122 airplanes; Model A319-111, -112, - 113, -114, -115, -131, -132, and -133 airplanes; and Model A320-211, - 212, -214, -231, -232, and -233 airplanes. As published, the AD number specified in the preamble and regulatory text is incorrect. This document corrects this error. In all other respects, the original document remains the same.
Amendment of Class E Airspace; Pocahontas, IA
This action amends the Class E airspace extending upward from 700 feet above the surface at Pocahontas Municipal Airport, Pocahontas, IA. This action is the result of an airspace review due to the decommissioning of the Pocahontas non-directional beacon (NDB). Additionally, the geographical coordinates of the airport are also being updated to coincide with the FAA's aeronautical database, which was inadvertently omitted in the NPRM docket.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.