Federal Aviation Administration 2019 – Federal Register Recent Federal Regulation Documents

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

Under the provisions of Title 49, U.S.C. Section 47151(d), notice is being given that the Federal Aviation Administration (FAA) is considering a request from the City of Augusta to waive the requirement that 0.13 acres of surplus property located at the Daniel Field Airport be used for aeronautical purposes. Currently, the ownership of the property provides for the protection of FAR Part 77 surfaces and compatible land use which would continue to be protected with deed restrictions required in the transfer of land ownership.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A320-214, -232, and -271N airplanes, and Model A321-231 airplanes. This proposed AD was prompted by a report of a production line inspection finding of damage on a main landing gear (MLG) side stay attachment outboard lug. This proposed AD would require an inspection for discrepancies of the MLG side stay attachment outboard lugs, left-hand and right-hand sides, and applicable corrective action, as specified in a European Union Aviation Safety Agency (EASA) AD, which will be incorporated by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 airplanes. This proposed AD was prompted by a report of failure of a wing strut leak test due to a missing bolt on the firewall. This proposed AD would require a one-time leak test of the strut upper spar areas for the left and right wing struts, and corrective action if necessary. The FAA is proposing this AD to address the unsafe condition on these products.

This action modifies Class E airspace extending upward from 700 feet above the surface at Walden-Jackson County Airport, Walden, CO, to accommodate a new area navigation (RNAV) procedure at the airport. Additionally, this action removes Class E airspace extending upward from 700 feet above the surface north of the airport that is not required to contain IFR procedures. This action also updates the geographic coordinates of the airport to match the FAA's data base. This action ensures the safety and management of instrument flight rules (IFR) operations at the Walden-Jackson County Airport.

These special conditions are issued for The Boeing Company (Boeing) Model 777 series airplanes. These airplanes will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport-category airplanes. This design feature is an inertia locking device (ILD) installed in passenger seats. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

This notice announces a meeting of the ARAC.

The FAA proposes to adopt a new airworthiness directive (AD) for various helicopters operating under experimental airworthiness certificates and various type certificated restricted category helicopters. This proposed AD was prompted by multiple accidents and incidents involving failure of the tail boom attachment structure and bolts. This proposed AD would require revising the Rotorcraft Flight Manual (RFM) for your helicopter to incorporate pre-flight checks; removing paint and sealant, and cleaning; repetitive inspections of structural components that attach the tail boom to the fuselage; and depending on the outcome of the inspections, repairing or replacing components, or re-bonding the structure. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to supersede Airworthiness Directive (AD) 2018-19-26, which applies to all Dassault Aviation Model MYSTERE- FALCON 200 airplanes. AD 2018-19-26 requires revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. Since the FAA issued AD 2018-19-26, the FAA determined that new or more restrictive airworthiness limitations are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain De Havilland Aircraft of Canada Limited Model DHC-8-400 series airplanes. This proposed AD was prompted by reports of wear on fuel couplings, bonding springs, and sleeves as well as fuel tube end ferrules and fuel component end ferrules. This proposed AD would require repetitive inspections of certain parts for discrepancies that meet specified criteria, and replacement as necessary; repetitive inspections of certain parts for damage and wear, and rework of parts; and electrical bonding checks of certain couplings. This proposed AD would also require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. For certain airplanes, this proposed AD would allow a modification that would terminate the repetitive inspections. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to supersede Airworthiness Directive (AD) 2003-09-04 R1, which applies to certain Bombardier, Inc., Model CL-600- 2B19 (Regional Jet series 100 & 440) airplanes. AD 2003-09-04 R1 requires revising the airworthiness limitations for certain structural inspections; repair if necessary; and submission of inspection findings to the airplane manufacturer. Since the FAA issued AD 2003-09-04 R1, the agency determined that additional airplanes are affected, that new or more restrictive airworthiness limitations are necessary, and that the compliance time must be revised to include a phase-in time for certain tasks. This proposed AD would revise the applicability to include additional airplanes; revise certain compliance times; and require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is superseding Airworthiness Directive (AD) 2019-19-11 for certain Pratt & Whitney (PW) PW1519G, PW1521G, PW1521GA, PW1524G, PW1525G, PW1521G-3, PW1524G-3, PW1525G-3, PW1919G, PW1921G, PW1922G, PW1923G, and PW1923G-A model turbofan engines. AD 2019-19-11 required initial and repetitive inspections of the low-pressure compressor (LPC) inlet guide vane (IGV) and the LPC rotor 1 (R1) and, depending on the results of the inspections, possible replacement of the LPC. This AD requires the same inspection of the LPC R1 for cracks or damage, removes the inspection of the LPC IGV for proper alignment, and expands the applicability to certain additional PW turbofan engines. This AD also reduces the compliance time for these inspections for certain PW turbofan engines. This AD was prompted by recent findings of cracks in the LPC R1 and an additional in-flight failure of the LPC R1. The FAA is issuing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A321-211, -212, -213, -231, and -232 airplanes. This proposed AD was prompted by a report of erroneous positioning of affected parts on the skin of the fuselage during the pre-drill phase, which could result in unwanted drill-starts. This proposed AD would require inspections for the presence of unwanted drill-starts on affected parts, and an inspection for cracks and corrective action if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which will be incorporated by reference. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A300 series airplanes. This proposed AD was prompted by a report that bleed and air conditioning systems were contaminated by hydraulic fluid, and an investigation revealed that hydraulic fluid contaminations caused the failure of check valves installed on the hydraulic reservoir air pressurization system. This proposed AD would require repetitive functional tests of the hydraulic reservoir air pressurization lines and repair or replacement, if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which will be incorporated by reference. The FAA is proposing this AD to address the unsafe condition on these products.

This notice announces a meeting of the SOCAC.

The Federal Aviation Administration is requesting public comment on a request by City of Charlotte, to release of land (176.113 acres) at Charlotte Douglas International Airport from federal obligations.

This notice contains a summary of a petition seeking relief from specified requirements of Federal Aviation Regulations. The purpose of this notice is to improve the public's awareness of, and participation in, the FAA's exemption process. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.

The FAA proposes to supersede airworthiness directive (AD) 2018-07-16 which applies to all Austro Engine GmbH model E4 and E4P diesel piston engines. AD 2018-07-16 requires initial and repetitive replacement of the waste gate controller and the control rod circlip. Since the FAA issued AD 2018-07-16, Austro Engine GmbH developed a modification of the waste gate control-rod fail-safe bridge and spring- loaded circlip that terminates the need for repetitive replacement of the waste gate controller and the control rod circlip. This proposed AD would retain the requirements of AD 2018-07-16 and requires engine modification by installing a waste gate control-rod fail-safe bridge and new spring-loaded circlip that terminates the initial and repetitive replacement requirements of AD 2018-07-16. The FAA is proposing this AD to address the unsafe condition on these products.

The FAA is superseding Airworthiness Directive (AD) 2011-18- 15, which applied to certain De Havilland Aircraft of Canada Limited Model DHC-8-400 series airplanes. AD 2011-18-15 required initial and repetitive torque checks of the bolt preload; detailed inspection of the barrel nuts and cradle for cracking, pitting, and corrosion if the bolt preload is correct; and replacement of certain hardware if necessary. This AD continues to require those actions. This AD also requires new inspections and replacement of certain hardware, which would terminate the repetitive torque checks and inspections; and removes airplanes from the applicability. This AD was prompted by in- service reports of cracked barrel nuts found at the front spar locations of the wing-to-fuselage attachment joints, and a loose washer in the barrel nut assembly. The FAA is issuing this AD to address the unsafe condition on these products.

In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval of a new collection. The collection involves the voluntary submission of information for registration of an Airman Knowledge Test as part of the FAA Airman Certification Process. The information collected is necessary to ensure compliance and proper registration of an individual for the necessary knowledge test for the certification or rating pursued by the individual.

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-243, -243F, -341, -342, and -343 airplanes. This AD was prompted by a determination that cracks can develop on the ripple damper weld of the hydraulic pressure tube assembly and reports of failure of the ripple damper of the hydraulic pressure tube assembly. This AD requires replacement of the affected hydraulic pressure tube assembly or modification of both engines, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

In accordance with the Paperwork Reduction Act of 1995, the FAA invites public comments about our intention to request Office of Management and Budget (OMB) approval to renew an information collection. The ``Aging Aircraft Program (Widespread Fatigue Damage)'' final rule amended FAA regulations pertaining to certification and operation of transport category airplanes to preclude widespread fatigue damage in those airplanes.

This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Model EC225LP helicopters. This AD requires determining the total hours time-in-service (TIS) of the free wheel shafts of certain main rotor gearboxes (MGBs), replacing the MGB or right-hand side (RH) free wheel shaft, installing placard(s), and revising the Rotorcraft Flight Manual (RFM) for your helicopter. This AD was prompted by a report of wear of the ramps of the RH free wheel shaft. The actions of this AD are intended to address an unsafe condition on these products.

The FAA is superseding Airworthiness Directive (AD) 2018-26- 07, which applied to all Airbus SAS Model A350-941 and -1041 airplanes. AD 2018-26-07 required repetitive greasing of the thrust reverser actuators (TRAs), dispatch restrictions, and maintenance procedure revisions. This AD requires actions specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD was prompted by the FAA's determination to add a requirement to replace the TRAs, which AD 2018-26-07 specified was not required at the time to provide the opportunity for the public to comment on the merits of that action. The FAA is issuing this AD to address the unsafe condition on these products.