Federal Aviation Administration March 2018 – Federal Register Recent Federal Regulation Documents

We are superseding Airworthiness Directive (AD) 2013-19-12 for GA 8 Airvan (Pty) Ltd Models GA8 and GA8-TC320 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and address an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the fuel system integral sump tank not meeting FAA regulations. We are issuing this AD to require actions to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for Pacific Aerospace Limited Model 750XL airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as incorrectly marked and annunciated low oil pressure indication warnings. We are issuing this AD to require actions to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all Airbus Model A318-111 and -112 airplanes; Model A319-111, -112, -113, - 114, and -115 airplanes; Model A320-211, -212, and -214 airplanes; and Model A321-111, -112, -211, -212, and -213 airplanes. This AD was prompted by reports of engine fan cowl door (FCD) losses on airplanes equipped with CFM56 engines due to operator failure to close the FCD during ground operations. This AD requires modification and re- identification, or replacement, of certain FCDs. This AD also requires installation of a placard. We are issuing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model MYSTERE-FALCON 900, FALCON 900EX, FALCON 2000, and FALCON 2000EX airplanes. This AD was prompted by reports of a loose screw on certain slat mechanical stop assemblies, and punctures in certain fuel caps. This AD requires a one-time inspection, and corrective action if necessary. We are issuing this AD to address the unsafe condition on these products.

The FAA is revising its rules for pilot compartment view to allow ground tests to demonstrate compliance for night operations. The requirement for night flight testing to demonstrate compliance is not necessary in every case. The revision will relieve the burden of performing a night flight test under certain conditions.

This action proposes to amend Class E airspace designated as a surface area at Iowa County Airport, Mineral Point, WI, by removing the part-time language from the airspace description. The FAA is proposing this action to change the status from part-time to full-time at the request of Chicago Air Route Traffic Control Center (ARTCC). This action would also make an editorial change to the airspace description by removing the city from the airport name.

These special conditions are issued for the Textron Aviation, Inc., model C90A King Air airplane. This airplane as modified by Nextant Aerospace will have a novel or unusual design feature associated with installation of an engine that includes an electronic engine control system. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

This action amends Class E airspace extending upward from 700 feet above the surface in Selinsgrove, PA. A new area navigation (RNAV) global positioning system (GPS) standard instrument approach procedure has been developed at Penn Valley Airport, requiring airspace reconfiguration at the airport. This action enhances the safety and airspace management of instrument flight rules (IFR) operations at the airport. This action also updates the geographic coordinates of the airport.

We propose to supersede Airworthiness Directive (AD) 2016-18- 01, which applies to certain The Boeing Company Model 737-600, -700, - 700C, -800, -900, and -900ER series airplanes. AD 2016-18-01 requires repetitive lubrication of the forward and aft trunnion pin assemblies of the right and left main landing gears (MLGs); repetitive inspection of these assemblies for corrosion and chrome damage, and related investigative and corrective actions, if necessary; and installation of new or modified trunnion pin assembly components, which terminates the repetitive lubrication and repetitive inspections. Since we issued AD 2016-18-01, we have determined that rotable parts were not addressed in that AD and that all airplanes of the affected models, excluding those with a certain configuration, should be inspected to determine if affected MLG trunnion pin assemblies are installed. This proposed AD would therefore add airplanes to the applicability. We are proposing this AD to address the unsafe condition on these products.

The FAA Aircraft Certification Service (AIR) and Flight Standards Service (AFS) have reorganized to align with functional organization design concepts. The AIR reorganization included eliminating product directorates and restructuring and re-designating field offices. The AFS reorganization included eliminating geographic regions, realigning headquarters organizations, and restructuring field offices. Currently, various rules in the Code of Federal Regulations refer to specific AIR and AFS offices that are obsolete after the reorganizations. This rule replaces specific references with generic references not dependent on any particular office structure. This rule does not impose any new obligations and is only intended to eliminate any confusion about with whom regulated entities and other persons should interact when complying with these various rules in the future.

The FAA is issuing this notice to advise the public of a meeting of Thirty Eighth RTCA SC-213 Enhanced Flight Vision Systems/ Synthetic Vision Systems (EFVS/SVS) Joint Plenary with EUROCAE Working Group 79.

We are revising airworthiness directive (AD) 2018-01-12 for Airbus Helicopters Model AS350B3 helicopters to correct an error. As published, AD 2018-01-12 referenced an incorrect monostable toggle switch part number (P/N) in the preamble and regulatory text. This document corrects the error. In all other respects, the original document remains the same.

We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model DHC-8-400 series airplanes. This proposed AD was prompted by reports of arcing and smoke emanating from the windshields. This proposed AD would require a revision to the maintenance or inspection program, as applicable, to include an inspection of the windshield moisture seal for signs of cracks, erosion, wear, and other deterioration; doing that inspection and repair if necessary; and re-torqueing the windshield heater terminal lugs and applying sealant to the windshield heater screw heads. We are proposing this AD to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for Airbus Helicopters Model AS332C, AS332C1, AS332L, AS332L1, AS332L2, and EC225LP helicopters. This AD requires inspecting the sliding cabin plug door (sliding door). This AD was prompted by the failure of the sliding door's jettison mechanism due to corrosion. The actions of this AD are intended to address an unsafe condition in these products.