Federal Aviation Administration February 7, 2017 – Federal Register Recent Federal Regulation Documents
Results 1 - 7 of 7
Twentieth Meeting of the NextGen Advisory Committee (NAC)
The FAA is issuing this notice to advise the public of a meeting of the Twentieth Meeting of the NextGen Advisory Committee (NAC).
Airworthiness Directives; DG Flugzeugbau GmbH
We propose to adopt a new airworthiness directive (AD) for DG Flugzeugbau GmbH Model DG-500MB gliders that are equipped with a Solo 2625 02 engine modified with a fuel injection system following the instructions of Solo Kleinmotoren GmbH Service Bulletin (SB)/Technische Mitteilung (TM) 4600-3 ``Fuel Injection System'') and identified as Solo 2625 02i. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as the potential of an in-flight shut-down and engine fire due to failure of the connecting stud for the two fuel injector mounts of the engine redundancy system on gliders equipped with a Solo 2625 02i engine. We are issuing this proposed AD to require actions to address the unsafe condition on these products.
Airworthiness Directives; Slingsby Aviation Ltd. Airplanes
We propose to adopt a new airworthiness directive (AD) for Slingsby Aviation Ltd. Models T67M260 and T67M260-T3A airplanes that would supersede AD 2015-11-01. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as failure of a brake master cylinder pivot pin, which could cause the rudder pedal mechanism to detach from the brake cylinder. We are issuing this proposed AD to require actions to address the unsafe condition on these products.
Airworthiness Directives; Piper Aircraft, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Piper Aircraft, Inc. Models PA-31T, PA-31T1, PA-31T2, PA-31T3, and PA- 31P-350 airplanes. This AD requires repetitive detailed visual inspections of the wiring below the main circuit breaker panel for proper clearance and evidence of damage and rerouting or replacing wires and/or parts as necessary. This AD was prompted by a fatal accident where evidence of thermal damage in this area was found. We are issuing this AD to correct the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by reports of skin cracking found at the corners of the aft entry and aft galley doorways. This AD requires repetitive inspections for cracking of the fuselage skin assembly and the bear strap at the corners of the aft entry and aft galley doorways, and repair if necessary, which terminates the repetitive inspections of the repaired areas. We are issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-200B, 747-300, 747-400, 747-400D, and 747- 400F series airplanes. This AD was prompted by a report of cracking in both the aluminum strut side skin, and corrosion resistant steel (CRES) outer spring beam support fitting. This AD requires inspections, related investigative and corrective actions, and a fastener installation modification. We are issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company
We are superseding Airworthiness Directive (AD) 2007-11-13 for all The Boeing Company Model 717-200 airplanes. AD 2007-11-13 required revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness to incorporate new removal limits for certain components of the flap system and to reduce the inspection intervals for fatigue cracking of principal structural elements (PSE). This new AD requires revising the maintenance or inspection program, as applicable, to incorporate reduced intervals for the inspections for three PSEs and add nondestructive inspections (NDIs). This AD was prompted by a new Airworthiness Limitations Instruction (ALI) revision that incorporates NDI techniques and reduced repetitive inspection intervals for three PSEs. We are issuing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
