Federal Aviation Administration January 22, 2015 – Federal Register Recent Federal Regulation Documents
Results 1 - 8 of 8
First Meeting: RTCA Special Committee 233, Addressing Human Factors/Pilot Interface Issues for Avionics
The FAA is issuing this notice to advise the public of the first meeting of the RTCA Special Committee 233, Addressing Human Factors/Pilot Interface Issues for Avionics.
Noise Exposure Map Notice; Receipt of Noise Compatibility Program and Request for Review San Antonio International Airport San Antonio, Texas
The Federal Aviation Administration (FAA) announces its determination that the noise exposure maps submitted by City of San Antonio Aviation Department for San Antonio International Airport under the provisions of 49 U.S.C. 47501 et. seq (Aviation Safety and Noise Abatement Act) and 14 CFR part 150 are in compliance with applicable requirements. The FAA also announces that it is reviewing a proposed noise compatibility program that was submitted for San Antonio International Airport under Part 150 in conjunction with the noise exposure map, and that this program will be approved or disapproved on or before July 11, 2015.
Notice of Intent To Rule on Request To Release Airport Property at Eufaula Municipal Aiport, Eufaula, Oklahoma, Correction
The FAA published a document in the Federal Register of December 5, 2014, concerning request for comments on the release of land at Eufaula Municipal Airport under the provisions of Section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21). The document contained the incorrect state.
Airworthiness Directives; Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A319-115, A319-133, A320-214, A320-232, and A320-233 airplanes. This emergency AD was sent previously to all known U.S. owners and operators of these airplanes. This AD requires repetitive detailed visual inspections to detect discrepancies of the wing lower skin surface and inboard main landing gear (MLG) support rib lower flange location fasteners and, depending on findings, accomplishment of applicable corrective action(s). This AD was prompted by reports of failure of certain fasteners located at the wing lower skin surface and inboard MLG support rib lower flange. We are issuing this AD to detect and correct discrepancies of the fasteners at the external surface of the lower wing skin and inboard MLG support rib lower flange, which could result in an airplane not meeting its maximum loads expected in service. This condition could result in structural failure.
Airworthiness Directives; Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This emergency AD was sent previously to all known U.S. owners and operators of these airplanes. This AD requires revising the airplane flight manual to advise the flightcrew of emergency procedures for abnormal Alpha Protection (Alpha Prot). This AD was prompted by a report of Angle of Attack (AoA) probes jamming on an in-service Airbus Model A321 airplane. Jamming of the two AoA probes during climb is attributed to water freezing under the AoA vane slinger, and led to activation of the Alpha Prot while the Mach number increased, which resulted in an airplane pitch down per design. We are issuing this AD to ensure that the flightcrew has procedures to counteract the pitch down order due to abnormal activation of the Alpha Prot. An abnormal Alpha Prot, if not corrected, could result in loss of control of the airplane.
Airworthiness Directives; Airbus Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200 Freighter, -200, and -300 series airplanes and Model A340-200, -300, -500, and -600 series airplanes. This emergency AD was sent previously to all known U.S. owners and operators of these airplanes. This AD requires revising the airplane flight manual to advise the flightcrew of emergency procedures for abnormal Alpha Protection (Alpha Prot). This AD was prompted by a report of Angle of Attack (AoA) probes jamming on an in-service Airbus Model A321 airplane. We are issuing this AD to ensure that the flightcrew has procedures to counteract the pitch down order due to abnormal activation of the Alpha Prot. An abnormal Alpha Prot, if not corrected, could result in loss of control of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We are superseding Airworthiness Directive (AD) 2011-09-11, for certain The Boeing Company Model 777-200 and -300 series airplanes. AD 2011-09-11 required repetitive inspections for hydraulic fluid contamination of the interior of the strut disconnect assembly; repetitive inspections for discrepancies of the interior of the strut disconnect assembly, if necessary; repetitive inspections of the exterior of the strut disconnect assembly for cracks, if necessary; corrective action if necessary; and an optional terminating action for the inspections. This new AD adds, for certain airplanes, an inspection of the side and top cover plates to determine if all cover plate attach fasteners have been installed, and installing any missing fasteners including doing an inspection for damage, and repair if necessary. This AD was prompted by reports of side and top cover plates installed with missing fastener bolts, which results in an unsealed opening on the system disconnect assembly. We are issuing this AD to detect and correct hydraulic fluid contamination, which can cause cracking of titanium parts in the system disconnect assembly; and also to detect and correct missing fasteners, which results in unsealed openings on the system disconnect assembly. Both unsafe conditions can compromise the engine firewall and result in fire hazards for both the engine compartment and the strut.
Airworthiness Directives; Mitsubishi Heavy Industries, Ltd. Airplanes
We are adopting a new airworthiness directive (AD) for certain Mitsubishi Heavy Industries, Ltd. Models MU-2B-30, MU-2B-35, MU-2B-36, MU-2B-36A, and MU-2B-60 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as stress corrosion cracking in the flanges of the airframe at stations 4610 and 5605. We are issuing this AD to require actions to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.