Federal Aviation Administration June 18, 2012 – Federal Register Recent Federal Regulation Documents
Results 1 - 22 of 22
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Airplanes
We propose to adopt a new airworthiness directive (AD) for all Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 airplanes, and Model EMB-145, -145ER, -145MR, -145LR, -145MP, and - 145EP airplanes. This proposed AD was prompted by a report of a lightning strike hitting an airplane tail boom causing certain rear bulkhead parts to jam an elevator control rod. This proposed AD would require installing or reworking, as applicable, metallic diverters and aluminum sheets; modifying the lights assembly on the tail boom rear movable fairing; and replacing the hood assembly with a new hood assembly and rerouting its electrical harness. We are proposing this AD to prevent lightning strikes from causing certain parts to contact the airplane pitch control system, which could reduce airplane controllability.
Airworthiness Directives; Eurocopter France Helicopters
We propose to adopt a new airworthiness directive (AD) for Eurocopter France Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, AS350D1, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters with certain Aerazur emergency flotation gear attachment brackets (brackets) installed. This proposed AD would require an initial and recurring inspection of the brackets for a crack, and if there is a crack, replacing the cracked bracket with an airworthy bracket. This proposed AD is prompted by reports of cracks on the brackets. The proposed actions are intended to prevent failure of the emergency flotation system and loss of float stability in the event of a water landing.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This proposed AD was prompted by a report of an inboard main landing gear (MLG) door assembly departure due to premature fatigue cracking in the inboard MLG door hinge fittings. This proposed AD would require repetitive inspections for cracking of the inboard MLG door hinge fittings; and modification of cracked fittings, which would terminate the repetitive inspections. We are proposing this AD to detect and correct fatigue cracking in the inboard MLG door hinge fittings which could result in loss of the MLG door assembly from the airplane; loss of the MLG door assembly could impact the flight control surfaces and result in reduced controllability of the airplane.
Airworthiness Directives; Eurocopter France Helicopters
We propose to adopt a new airworthiness directive (AD) for all Eurocopter France (Eurocopter) Model SA-365N, SA-365N1, AS-365N2, AS 365 N3, EC 155B, EC155B1, SA-365C, SA-365C1, SA-365C2, and SA-366G1 helicopters. This proposed AD is prompted by reports of corrosion on the main gearbox (MGB) casing lower area between the two servo-control anchoring fitting attachment ribs. An investigation determined that the corrosion was associated with sealing compound on the lower part of the fitting/casing attachment. The proposed actions are intended to detect corrosion on the MGB casing, which could lead to a crack, failure of the MGB, and subsequent loss of control of the helicopter.
Airworthiness Directives; Eurocopter France Helicopters
We propose to adopt a new airworthiness directive (AD) for Eurocopter France EC130B4 helicopters. This proposed AD is prompted by an in-flight cracking and failure of a center windscreen. The proposed actions are intended to detect a crack in the blending radii of the center windscreen to prevent failure of the windscreen, injury to the flight crew, and subsequent loss of control of the helicopter.
Airworthiness Directives; Airbus Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A300 B4-601, B4-603, and B4-605R airplanes, Model A300 F4-605R airplanes, Model A300 C4-605R Variant F airplanes, and Model A310-204 and -304 airplanes, powered by General Electric (GE) CF6-80C2 series engines. This proposed AD was prompted by reports of two single-engine flame-out events during inclement weather. This proposed AD would require installing a shunt of the rotary selector (introducing an auto-relight function). We are proposing this AD to prevent a long engine restart sequence after a non-selection of continuous re-light by the crew and a flame-out event of both engines, which could result in reduced controllability of the airplane, especially at low altitude.
Airworthiness Directives; Airbus Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A330-200 freighter series airplanes, Model A330- 200 and -300 series airplanes, and Model A340-200, -300, -500, and -600 series airplanes. This proposed AD was prompted by reports of the ram air turbine (RAT) not deploying when tested. This proposed AD would require identification of the supplier, part number, and serial number of the installed RAT actuator, and re-identification of the actuator and RAT, or replacement of the RAT actuator with a serviceable unit and re-identification of the RAT, if necessary. We are proposing this AD to prevent non-deployment of the RAT, which if occurred following a total engine flame-out, or during a total loss of normal electrical power generation, could result in reduced control of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain Boeing Company Model 777-200, -200LR, -300, and -300ER series airplanes. This proposed AD was prompted by reports of in-service events related to electrical power system malfunctions resulting in damage to electrical load management system (ELMS) P200 and P300 power panels and the surrounding area. This proposed AD would require installing enclosure trays to contain debris in certain ELMS panels, and replacing certain ELMS contactors. We are proposing this AD to prevent contactor failures, which could result in uncontained hot debris flow due to ELMS contactor breakdown, consequent smoke and heat damage to airplane structure and equipment during ground operations, and possible injuries to passengers and crew.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Specific Release Form
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on April 3, 2012, vol. 77, no. 64, pages 20093-20094. The information garnered from a signed Specific Release form is used by FAA Special Agents to obtain information related to a specific investigation. That information is then provided to the FAA decision making authority to make FAA employment and/or pilot certification/ revocation determinations.
Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of Information Collection: Pilot Schools
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to renew an information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on April 3, 2012, vol. 77, no. 64, page 20093. The information on FAA Form 8420-8, Application for Pilot School Certificates, is required from applicants who wish to be issued pilot school certificates and associated ratings.
Nineteenth Meeting: RTCA Special Committee 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS)
The FAA is issuing this notice to advise the public of the nineteenth meeting of RTCA Special Committee 213, Enhanced Flight Vision Systems/Synthetic Vision Systems (EFVS/SVS).
Special Conditions: Gulfstream Aerospace LP (GALP), Model Gulfstream G280 Airplane; Aircraft Electronic System Security Protection From Unauthorized External Access
These special conditions are issued for the Gulfstream Aerospace LP, Model Gulfstream G280 airplane. This airplane will have novel or unusual design features associated with the architecture and connectivity capabilities of the airplane's computer systems and networks, which may allow access to or by external computer systems and networks. Connectivity to, or access by, external systems and networks may result in security vulnerabilities to the airplane's systems. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for these design features. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Airworthiness Directives; Enstrom Helicopter Corporation Helicopters
We are superseding an existing airworthiness directive (AD) for Enstrom Helicopter Corporation (Enstrom) Model F-28C, F-28C-2, F- 28F, 280C, 280F, 280FX, TH-28, 480, and 480B helicopters to add another trim relay to the applicability and to revise the modification instructions. This AD is prompted by the discovery that another part- numbered trim relay, inadvertently omitted from the current AD, may contain the same unsafe condition. These actions are intended to prevent failure of the cyclic trim system and subsequent loss of control of the helicopter.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 717-200 airplanes. This AD was prompted by reports of cracks found on the center section ribs of the horizontal stabilizers. This AD requires repetitive inspections for cracking of the aft face of the left and right rib hinge bearing lugs of the center section of the horizontal stabilizer; and crack measurement, repairs, post-repair repetitive inspections, and installation of a new center section rib if necessary. We are issuing this AD to detect and correct cracking in the left and right bearing lugs of the rib hinge spreading at the same time, which could result in failure of both hinge bearing lugs. Failure of the hinge bearing lugs could result in the inability of the horizontal stabilizer to sustain flight loads and thereby reduce the controllability of the airplane.
Airworthiness Directives; AGUSTA S.p.A. Helicopters
We are adopting a new airworthiness directive (AD) for Agusta S.p.A. (Agusta) Model AW139 helicopters to determine if the hardware that attaches the upper end of collective control rod C2 to torque tube C3 is properly installed. This AD is prompted by the discovery of an incorrectly-attached collective control rod. These actions are intended to prevent separation of the collective control rod from the torque tube, loss of control of the collective pitch, and subsequent loss of control of the helicopter.
Airworthiness Directives; The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) for certain The Boeing Company Model 737-300, -400, and -500 series airplanes. That AD currently requires repetitive external detailed inspections or non-destructive inspections to detect cracks in the fuselage skin along the chem-mill steps at stringers S-1 and S-2R, between station (STA) 400 and STA 460, and repair if necessary. This new AD adds inspections for cracking in additional fuselage skin locations, and repair if necessary. This new AD also reduces the inspection thresholds and repetitive intervals for certain airplanes. This AD was prompted by reports of additional crack findings of the fuselage skin at the chem-mill steps. We are issuing this AD to detect and correct fatigue cracking of the fuselage skin panels at the chem- mill steps, which could result in sudden fracture and failure of the fuselage skin panels, and consequent rapid decompression of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We are superseding two existing airworthiness directives (ADs) for certain Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. The first existing AD currently requires, for certain airplanes, repetitive inspections of the Station (STA) 348.2 frame to detect cracking under the stop fittings and intercostal flanges at stringers S-14L, S-15L, and S-16L, and corrective action if necessary. The second existing AD currently requires repetitive inspections to detect cracking of the intercostal webs, attachment clips, and stringer splice channels, and corrective action if necessary. This new AD requires that the inspection for cracking under the stop fittings be done on additional airplanes; extends the repetitive interval for certain airplanes; adds a one-time inspection to detect missing fasteners; and updates or adds certain inspection and repair instructions. This new AD also requires, for certain airplanes, repetitive inspections of the cargo barrier net fitting for cracking, and repair if necessary. This new AD also adds, for certain airplanes, repetitive inspections for cracking of the stringer S-15L aft intercostal, and repair if necessary. This AD was prompted by reports of cracking of the STA 348.2 frame above the two outboard fasteners attaching the frame inner chord and door stop fittings, and in the outboard chord at stringer S-16L. We have also received reports of missing fasteners in the STA 348.2 frame inner chord. We are issuing this AD to detect and correct fatigue cracking of the intercostals on the forward and aft sides of the forward entry door cutout, which could result in loss of the forward entry door and rapid decompression of the airplane.
Airworthiness Directives; Airbus Airplanes
We are superseding an existing airworthiness directive (AD) for all Airbus Model A300 B4-600, B4-600R and A300 F4-600R series airplanes, Model A300 C4-605R Variant F airplanes, and Model A310 series airplanes. That AD currently requires modifying the wiring in the right-hand electronics rack. This new AD requires replacing the cockpit multi-tank indicators (MTI), and for certain airplanes, replacing high-level, low-level, and overflow sensors and their harness connectors, and re-instating the low-level warning indication to the cockpit MTI. This AD was prompted by reports of failures of four fuel level sensor-amplifier and MTI units. This AD also adds Model A310 series airplanes to the applicability. We are issuing this AD to prevent degradation of the electrical insulation sleeves of the low- level indication lamps on the MTI, which could cause a short circuit that might result in high voltage being conveyed to the high- and low- level sensors in the wing tanks. This condition could cause the level sensor to heat above acceptable limits, possibly resulting in a fuel tank explosion, and consequent loss of the airplane.
Airworthiness Directives; Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, and Model CL-600-2D24 (Regional Jet Series 900) airplanes. This AD was prompted by reports of a bleed air leak from the high pressure ducts which was not immediately detected by the bleed leak detection system. This AD requires installing new sensing elements in the main landing gear wheel well and the overwing area, protective blankets on the upper surface of the wing box and fuel tubes, and protective shields on the rudder quadrant support-beam in the aft equipment compartment. We are issuing this AD to prevent an undetected bleed air leak which can cause loss of rudder control, can lead to degradation of structural integrity, and could be a potential heat source that can lead to fuel being ignited.
Airworthiness Directives; BAE SYSTEMS (Operations) Limited Airplanes
We are adopting a new airworthiness directive (AD) for all BAE SYSTEMS (Operations) Limited Model 4101 airplanes. This AD was prompted by reports of cracking found in the wing rear spar. This AD requires a one-time detailed inspection for cracks, corrosion, and other defects of the rear face of the wing rear spar, and repair if necessary. We are issuing this AD to detect and correct cracking in the rear spar, which could propagate to a critical length, possibly affecting the structural integrity of the area and resulting in a fuel tank rupture, with consequent damage to the airplane and possible injury to its occupants.
Airworthiness Directives; SOCATA Airplanes
We are adopting a new airworthiness directive (AD) for SOCATA Model TBM 700 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as installation of an incorrect part number during overhaul of the nose landing gear. We are issuing this AD to require actions to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
