Federal Aviation Administration November 4, 2011 – Federal Register Recent Federal Regulation Documents
Results 1 - 7 of 7
Airworthiness Directives; DASSAULT AVIATION Model MYSTERE-FALCON 900 Airplanes
We propose to adopt a new airworthiness directive (AD) for all DASSAULT AVIATION Model MYSTERE-FALCON 900 airplanes. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; The Boeing Company Model 777-200 and -300 Series Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300 series airplanes. This proposed AD would require replacing certain single-tabbed bonding brackets in the airplane empennage with two-tabbed bonding brackets. This proposed AD would also require, for certain airplanes, installing new bonding jumpers, and measuring the resistance of the modified installation to verify resistance is within specified limits. This proposed AD was prompted by reports of two failures of the single- tabbed bracket on the rudder. We are proposing this AD to prevent failure of the bonding jumper bracket, which could result in loss of lightning protection ground path, which could lead to increased lightning-induced currents and subsequent damage to composite structures, hydraulic tubes, and actuator control electronics. In the event of a lightning strike, loss of lightning ground protection could result in the loss of control of the airplane.
Airworthiness Directives; Bombardier, Inc. Airplanes
We are adopting a new airworthiness directive (AD) for Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Sicma Aero Seat Passenger Seat Assemblies, Installed on, But Not Limited to, ATR-GIE Avions de Transport Régional Airplanes
We are adopting a new airworthiness directive (AD) for Sicma Aero Seat Model 9401, 9402, 9404, 9405, 9406, 9407, 9408, and 9409 series passenger seat assemblies, installed on, but not limited to, ATR-GIE Avions de Transport R[eacute]gional Model ATR42 and ATR72 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bell Helicopter Textron, Inc. (Bell), Model 205A-1, 205B, 210, and 212 Helicopters
This amendment supersedes an existing airworthiness directive (AD) for Bell Model 205B and 212 helicopters with certain main rotor blade (blade) assemblies installed. That AD currently requires washing the upper and lower surfaces of each blade and visually inspecting the grip plates, doublers, and the remaining upper and lower surfaces of the blades in the area between blade stations 24.5 to 40 for an edge void, corrosion, or a crack. This amendment retains the requirements of that AD for the affected part-numbered blades but increases the scope and frequency of the inspections and expands the applicability to include the Model 205A-1 and 210 helicopters, additional blade part numbers, and all helicopter serial numbers for the affected helicopter models. This amendment also requires applying a light coat of preservative oil (C-125) to all surfaces of the blade in addition to the inspection areas as required in the existing AD. This amendment is prompted by an additional report of a fatigue crack on a blade installed on a Model 212 helicopter. The actions specified by this AD are intended to detect an edge void, corrosion, or a crack on a blade, and to prevent loss of a blade and subsequent loss of control of the helicopter.
Airworthiness Directives; Eurocopter Deutschland GmbH (ECD) Model MBB-BK 117 C-2 Helicopters
This amendment adopts a new airworthiness directive (AD) for ECD Model MBB-BK 117 C-2 helicopters. This action requires revising the Rotorcraft Flight Manual (RFM) by inserting certain temporary pages into the Emergency and Performance Data sections of the RFM to alert the operators to monitor the power display when a generator is deactivated and provides appropriate actions. This amendment is prompted by reports of too high a current flow when one generator is deactivated. The actions specified in this AD are intended to prevent failure of the remaining generator when one generator is deactivated, loss of electrical power, loss of systems necessary for flight safety, and subsequent loss of control of the helicopter.
Airworthiness Directives; Agusta S.p.A. (Agusta) Model AB139 and AW139 Helicopters
This amendment adopts a new airworthiness directive (AD) for the specified Agusta model helicopters. This action requires inspecting certain modules and related connectors for corrosion. If there is corrosion on the connectors, this AD requires cleaning the connectors before further flight. If there is corrosion on a module, before further flight, this AD requires replacing the module with an airworthy module. This AD also requires modifying the Number 2 Modular Avionic Unit (MAU) ventilation duct. This amendment is prompted by some in- flight emergencies due to internal corrosion of the MAU circuit card assemblies. The actions specified in this AD are intended to detect corrosion of certain modules to prevent the display of misleading data to the flight crew, disengagement of the flight director modes of the autopilot or other alert system, increased workload of the flight crew, and subsequent loss of control of the helicopter.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
