Federal Aviation Administration August 22, 2011 – Federal Register Recent Federal Regulation Documents
Results 1 - 16 of 16
Restrictions on Operators Employing Former Flight Standards Service Aviation Safety Inspectors
This rule will prohibit any person holding a certificate from knowingly employing, or making a contractual arrangement with, certain individuals to act as an agent or a representative of the certificate holder in any matter before the FAA under certain conditions. These restrictions will apply if the individual, in the preceding 2-year period directly served as, or was directly responsible for the oversight of, a Flight Standards Service Aviation Safety Inspector, and had direct responsibility to inspect, or oversee the inspection of, the operations of the certificate holder. This rule will also apply to persons who own or manage fractional ownership program aircraft that are used to conduct operations under specific regulations described in this document. This rule will establish these restrictions to prevent potential organizational conflicts of interest which could adversely affect aviation safety.
Airworthiness Directives; General Electric Company CF34-10E2A1; CF34-10E5; CF34-10E5A1; CF34-10E6; CF34-10E6A1; CF34-10E7; and CF34-10E7-B Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above with certain part number (P/N) fan rotor spinners installed. This AD requires removing from service certain fan rotor blade retainers, and removing from service the fan rotor spinner support that was installed with those fan rotor blade retainers. This AD was prompted by a fan rotor spinner support found cracked at the attachment lugs. We are issuing this AD to prevent high-cycle fatigue cracking of the fan rotor spinner support attachment lugs, leading to separation of the fan rotor spinner assembly, uncontained failure of the engine, and damage to the airplane.
Airworthiness Directives; General Electric Company (GE) CF6-45 Series and CF6-50 Series Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires performing a fluorescent penetrant inspection (FPI) of the low-pressure turbine (LPT) rotor stage 3 disk at every shop visit at which the LPT module is separated from the engine. This AD was prompted by seven reports of uncontained failures of LPT rotor stage 3 disks and eight reports of cracked LPT rotor stage 3 disks found during shop visit inspections. We are issuing this AD to prevent LPT rotor separation, which could result in an uncontained engine failure and damage to the airplane.
Airworthiness Directives; Rolls-Royce plc (RR) Trent 800 Series Turbofan Engines
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Establishment of Area Navigation Route Q-37; Texas
This action establishes a high altitude area navigation (RNAV) route, designated Q-37, extending between the Pueblo, Colorado, VHF omnidirectional range/tactical air navigation (VORTAC) navigation aid and the Fort Stockton, Texas, VORTAC. The new route provides pilots and air traffic controllers with an efficient alternate route around potentially constrained airspace during convective weather events in west Texas.
Proposed Amendment of Class E Airspace; Luray, VA
This action proposes to amend Class E Airspace at Luray, VA, as new Standard Instrument Approach Procedures have been developed at Luray Caverns Airport. This action would enhance the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport. This action also would update the geographic coordinates of the airport.
Proposed Amendment of Class E Airspace; Jacksonville, NC
This action proposes to amend Class E Airspace at Jacksonville, NC, as new Standard Instrument Approach Procedures have been developed at Albert J Ellis Airport. This action would enhance the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport.
Proposed Amendment of Class E Airspace; Pelion, SC
This action proposes to amend Class E Airspace at Pelion, SC, as new Standard Instrument Approach Procedures have been developed at Lexington County Airport at Pelion. This action would enhance the safety and airspace management of Instrument Flight Rules (IFR) operations at the airport. This action also would recognize the airport name change to Lexington County Airport at Pelion.
Establishment of Class E Airspace; Forest, VA
This action establishes Class E Airspace at Forest, VA, to accommodate the new Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedures serving New London Airport. This action enhances the safety and airspace management of Instrument Flight Rules (IFR) operations within the National Airspace System.
Activation of Ice Protection
This action revises the operating rules for flight in icing conditions. For certain airplanes certificated for flight in icing, the new standards require either installation of ice detection equipment or changes to the airplane flight manual to ensure timely activation of the airframe ice protection system. This action is the result of information gathered from icing accidents and incidents. It is intended to increase the level of safety when airplanes fly in icing conditions.
Airworthiness Directives; Airbus Model A330-200, A330-300, A340-300, A340-500, and A340-600 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Airworthiness Directives; Embraer-Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-500 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), Model CL-600-2D15 (Regional Jet Series 705), and Model CL-600-2D24 (Regional Jet Series 900) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; The Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), and MD-88 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires repetitive inspections for cracking of the lower rear spar caps of the wings, and related investigative and corrective actions if necessary. This AD also requires repetitive inspections of certain repaired areas. This AD was prompted by reports of cracking of the wing rear spar lower cap at the outboard flap and inboard drive hinge at station Xrs=164.000; the cracking is due to material fatigue from normal flap operating loads. We are issuing this AD to detect and correct such fatigue cracking, which could result in fuel leaks, damage to the wing skin or other structure, and consequent reduced structural integrity of the wing.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.