Federal Aviation Administration September 2010 – Federal Register Recent Federal Regulation Documents

This notice announces the bi-annual meeting of the Federal Aviation Administration (FAA) Aeronautical Charting Forum (ACF) to discuss informational content and design of aeronautical charts and related products, as well as instrument flight procedures development policy and design criteria.

The FAA is correcting airworthiness directive (AD) 2010-11-09, which published in the Federal Register. That AD applies to TAE models TAE 125-01 and TAE 125-02-99 reciprocating engines, installed in, but not limited to, Diamond Aircraft Industries model DA 42 airplanes. The part number for engine model TAE 125-01 is missing a digit in paragraph (c) and in paragraph (e)(3). This document corrects those part numbers. In all other respects, the original document remains the same.

This action changes the using agency of Restricted Area R- 5113, Socorro, NM, to ``U.S. Air Force, Air Force Research Laboratory.'' There are no changes to the boundaries; designated altitudes; time of designation; or activities conducted within the affected restricted area.

Pursuant to Section 10(a)(2) of the Federal Advisory Committee Act (Pub. L. 92-463, 5 U.S.C. App. 2), notice is hereby given of a meeting of the Commercial Space Transportation Advisory Committee (COMSTAC). The meeting will take place on Thursday, October 7, 2010, starting at 8 a.m. at the National Housing Center, 1201 15th Street, NW., Washington, DC 20005.

We are revising an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2010-16-51, which was sent previously to all known U.S. owners and operators of Eurocopter France (Eurocopter) Model SA330J helicopters by individual letters. This AD requires, within 10 hours time-in-service (TIS), inspecting for a gap between the main gearbox (MGB) oil cooling fan assembly (fan) rotor blade and the upper section of the guide vane bearing housing. This inspection must be accomplished by using a feeler gauge attached to a rigid rod. If the feeler gauge cannot be inserted between the blade and the housing, this AD requires replacing the two fan rotor shaft bearings with two airworthy bearings. This AD is prompted by the separation of a fan rotor blade that caused puncture holes in the transmission deck. This condition, if not corrected, could lead to damage to the hydraulic lines and flight controls, and subsequent loss of control of the helicopter.

We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for certain Model 737-100 and -200 series airplanes. This AD requires repetitive inspections for cracking and damaged fasteners of certain fuselage frames and stub beams, and corrective actions if necessary. For certain airplanes, this AD also requires repetitive inspections for cracking of the inboard chord fastener hole of the frame at body station 639, stringer S-16, and corrective actions if necessary. For certain airplanes, this AD also requires an inspection to determine the edge margin of the lower chord. For airplanes with a certain short edge margin, this AD requires repetitive inspections for cracking, and corrective actions if necessary; replacing the lower chord terminates the repetitive inspections. This AD requires an eventual preventive modification. For certain airplanes, doing the modification or a repair terminates the repetitive inspections for the repaired or modified frame only. For airplanes on which the modification or repair is done at certain body stations, this AD requires repetitive inspections for cracking of certain frame webs and inner and outer chords, and corrective actions if necessary. For certain other airplanes, this AD requires a modification which includes reinforcing the body frame inner chords, replacing the stub beam upper chords and attach angles, and reinforcing the stub beam web. This AD results from reports of fatigue cracks at certain frame sections, in addition to stub beam cracking, caused by high flight cycle stresses from both pressurization and maneuver load. We are issuing this AD to detect and correct fatigue cracking of certain fuselage frames and stub beams, and possible severed frames, which could result in reduced structural integrity of the frames. This reduced structural integrity can increase loading in the fuselage skin, which will accelerate skin crack growth and result in rapid decompression of the fuselage.

This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.