Federal Aviation Administration August 18, 2010 – Federal Register Recent Federal Regulation Documents
Results 1 - 21 of 21
Airworthiness Directives; B/E Aerospace Protective Breathing Equipment Part Number 119003-11 Installed on Various Transport Airplanes
We propose to adopt a new airworthiness directive (AD) for various transport airplanes equipped with certain B/E Aerospace protective breathing equipment (PBE) units. This proposed AD would require removing affected PBE units. This proposed AD results from reports of potentially defective potassium superoxide canisters used in PBE units, which could result in an exothermic reaction and ignition. We are proposing this AD to prevent PBE units from igniting, which could result in a fire and possible injury to the flightcrew or other persons.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of Title 14, Code of Federal Regulations (CFR) part 25. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Petition for Exemption; Summary of Petition Received
This notice contains a summary of a petition seeking relief from specified requirements of 14 CFR. The purpose of this notice is to improve the public's awareness of, and participation in, this aspect of FAA's regulatory activities. Neither publication of this notice nor the inclusion or omission of information in the summary is intended to affect the legal status of the petition or its final disposition.
Special Conditions: Cirrus Design Corporation Model SF50 Airplane; Function and Reliability Testing
These special conditions are issued for the Cirrus Design Corporation SF50 airplane. This airplane will have a novel or unusual design feature(s) associated with the complex design and performance features consistent with larger airplanes. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Special Conditions: AeroMech, Incorporated; Hawker Beechcraft Corporation, Model B200 and Other Aircraft Listed in Table 1, Approved Model List (AML); Installation of MD835 Lithium Ion Battery
These special conditions are issued for the AeroMech, Incorporated; Hawker Beechcraft Corporation, model B200 and other part 23 aircraft listed on the AML. These airplanes as modified by AeroMech, Incorporated will have a novel or unusual design feature(s) associated with installation of the Mid-Continent Instruments MD835 Lithium Ion (Li-ion) battery. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Proposed Amendment of Class E Airspace; Kokomo, IN
This action proposes to amend Class E airspace at Kokomo, IN. Additional controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Kokomo Municipal Airport. Minor adjustments to geographic coordinates also would be made. This action also would change the name of Logansport Municipal Airport. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) operations at the airport.
Proposed Amendment of Class E Airspace; Kennett, MO
This action proposes to amend Class E airspace at Kennett, MO. Decommissioning of the Kennett non-directional beacon (NDB) at Kennett Memorial Airport has made this action necessary for the safety and management of Instrument Flight Rules (IFR) operations at the airport.
Airworthiness Directives; Rolls-Royce plc RB211-524C2 Series Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Pratt & Whitney JT8D-7, -7A, -7B, -9, -9A, -11, -15, -15A, -17, -17A, -17R, and -17AR Series Turbofan Engines
The FAA proposes to supersede an existing airworthiness directive (AD) for Pratt & Whitney (PW) JT8D-1, -1A, -1B, -7, -7A, -7B,
Airworthiness Directives; Pratt & Whitney JT8D-209, -217, -217A, -217C, and -219 Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for Pratt & Whitney (PW) JT8D-209, -217, -217A, -217C, and -219 turbofan engines. That AD currently requires revisions to the engine manufacturer's time limits section (TLS) to include enhanced inspection of selected critical life-limited parts at each piece-part opportunity. This AD requires modifying the TLS of the manufacturer's engine manual and an air carrier's approved continuous airworthiness maintenance program to incorporate additional inspection requirements. Pratt & Whitney has developed and the FAA has approved improved inspection procedures for the critical life-limited parts. The mandatory inspections are needed to identify those critical rotating parts with conditions, which if allowed to continue in service, could result in uncontained failures. We are issuing this AD to prevent critical life- limited rotating engine part failure, which could result in an uncontained engine failure and damage to the airplane.
Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals
The FAA publishes a monthly notice, as appropriate, of PFC approvals and disapprovals under the provisions of the Aviation Safety and Capacity Expansion Act of 1990 (Title IX of the Omnibus Budget Reconciliation Act of 1990) (Pub. L. 101-508) and Part 158 of the Federal Aviation Regulations (14 CFR part 158). This notice is published pursuant to paragraph d of Sec. 158.29.
Airworthiness Directives; Various Aircraft Equipped With Rotax Aircraft Engines 912 A Series Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Airbus Model A330-223, -321, -322, and -323 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Pilatus Aircraft Ltd. Model PC-12/47E Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Eurocopter France (Eurocopter) Model AS350B, BA, B1, B2, C, D, and D1 Helicopters and Model AS355E, F, F1, F2, and N Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2010-11-51, which was sent previously to all known U.S. owners and operators of the specified Eurocopter model helicopters by individual letters. This AD requires visually inspecting the tail gearbox (TGB) control lever for a crack. If a crack is found, this AD also requires replacing the cracked TGB control lever with an airworthy TGB control lever. Optional terminating actions for the inspection requirements of this AD can be done by either replacing a TGB control lever with an airworthy TGB control lever that is marked with an ``X'' near the part number or stripping the rework area and dye-penetrant inspecting that area for a crack, and if no crack is found, reworking and marking the TGB control lever. If a crack is found, removing and replacing the cracked TGB control lever with an airworthy TGB control lever is required. This AD is prompted by several reports of cracking in a TGB control lever. The actions specified by this AD are intended to prevent failure of the TGB control lever, loss of tail rotor control, and subsequent loss of control of the helicopter.
Airworthiness Directives; Agusta S.p.A. Model A119 and AW119 MKII Helicopters
This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2010-15-51, which was sent previously to all known U.S. owners and operators of Agusta S.p.A. (Agusta) Model A119 and AW119 MKII helicopters by individual letters. This AD requires, within 5 hours time-in-service (TIS), and thereafter at intervals not to exceed 50 hours TIS, removing the cover of each pilot and co-pilot control box assembly (control box) and inspecting each rotary variable differential transformer (RVDT) control gear locking pin (locking pin) for proper position. If a locking pin is recessed, extended, or missing, this AD requires replacing the control box before further flight. This amendment is prompted by a report that an RVDT locking pin that was installed on a Model AW119 MKII helicopter moved from its proper position, resulting in loss of connectivity of the pilot and co-pilot throttle controls. The actions specified by this AD are intended to prevent the RVDT locking pin from moving from its proper position, which could lead to loss of manual engine throttle control, and subsequent loss of control of the helicopter.
Airworthiness Directives; Airbus Model A380-800 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; The Boeing Company Model 767-300 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 767-300 series airplanes. This AD requires replacing a wire bundle clamp and installing a tetrafluoroethylene (TFE 2X) sleeve. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent chafing of a wiring bundle, which could result in a high-energy short and, consequently, a possible ignition source in the center auxiliary fuel tank.
Airworthiness Directives; Airbus Model A330-201, -202, -203, -223, -243, -301, -302, -303, -321, -322, -323, -341, -342, and -343 Airplanes, Model A340-211, -212, -213, -311, -312, and -313 Airplanes, and Model A340-541 and -642 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires replacement of the power control relays in the P91 and P92 power distribution panels for the fuel boost and override pumps with new, improved relays having a ground fault interrupter (GFI) feature, or installation and maintenance of universal fault interrupters (UFIs) using a certain supplemental type certificate. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent pump housing burn-through due to electrical arcing, which could create a potential ignition source inside a fuel tank. This condition, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; McDonnell Douglas Corporation Model MD-90-30 Airplanes
We are adopting a new airworthiness directive (AD) for certain Model MD-90-30 airplanes. This AD requires inspecting for corrosion of the retract cylinder support fitting for the main landing gear (MLG) and the mating bore for the support fitting in the MLG trunnion fitting, performing corrective actions if necessary, and replacing cadmium-plated retract cylinder support bushings and bearings. This AD results from reports of the retract cylinder support fitting for the MLG failing during gear extension and subsequently damaging the hydraulic system. We are issuing this AD to prevent corrosion and damage that could compromise the integrity of the retract cylinder support fitting for the MLG, which could adversely affect the airplane's safe landing.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
