Department of Transportation November 14, 2023 – Federal Register Recent Federal Regulation Documents
Results 1 - 8 of 8
Notice of Meeting of the Transit Advisory Committee for Safety
The Federal Transit Administration (FTA) announces a public meeting of the Transit Advisory Committee for Safety (TRACS).
Airworthiness Directives; Airbus Helicopters
The FAA is superseding Airworthiness Directive (AD) 2022-01- 05, which applied to certain Airbus Helicopters Model EC130T2 helicopters. AD 2022-01-05 required repetitive visual inspections of the rivets on the rear transmission shaft bearing support, inspections of the local structure, and rivet heads on the left-hand and right-hand sides of the rear transmission shaft bearing support for cracking, missing, loose, or sheared rivets. AD 2022-01-05 also required reporting the results of those inspections and depending on the results, applicable corrective action. Since the FAA issued AD 2022-01- 05, Airbus Helicopters revised its service information to add procedures to improve visual inspections of the rivets on the rear transmission shaft bearing support. This AD was prompted by the determination that certain modified helicopters may have finishing paint applied to the gutter, which could prevent detection of cracks during inspections. This AD also extends the repetitive compliance time interval for certain inspections. This AD continues to require certain actions in AD 2022-01-05 and requires a one-time visual inspection for paint in the gutter area, and removal of paint if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Engines
The FAA is superseding Airworthiness Directive (AD) 2021-21-13 for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent 1000 engines. AD 2021-21-13 required the operator to revise the airworthiness limitation section (ALS) of their existing approved aircraft maintenance program (AMP) by incorporating the revised tasks of the applicable time limits manual (TLM) for each affected model engine. Since the FAA issued AD 2021-21-13, the manufacturer has revised the TLM, introducing new and more restrictive instructions. This AD is prompted by the manufacturer revising the engine TLM life limits of certain critical rotating parts. This AD requires revisions to the ALS of the operator's existing approved AMP, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Proposed Agency Information Collection Activities; Comment Request
Under the Paperwork Reduction Act of 1995 (PRA) and its implementing regulations, this notice announces that FRA is forwarding the Information Collection Request (ICR) summarized below to the Office of Management and Budget (OMB) for review and comment. The ICR describes the information collection and its expected burden. On August 18, 2023, FRA published a notice providing a 60-day period for public comment on the ICR.
Transit Worker Hours of Service and Fatigue Risk Management Virtual Listening Session
The Federal Transit Administration (FTA) will hold a virtual public listening session concerning the topics of hours of service and fatigue risk management for transit workers on December 5, 2023. On October 30, 2023, FTA published an Advance Notice of Proposed Rulemaking (ANPRM) seeking public input on those topics. The virtual listening session will allow all interested persons an opportunity to present comments, views, and relevant research on those topics in addition to providing written comments to the docket. A transcript will be placed in the rulemaking docket for public inspection.
Airworthiness Directives; GE Aviation Czech s.r.o. (Type Certificate Previously Held by WALTER Engines a.s., Walter a.s., and MOTORLET a.s.) Engines
The FAA proposes to supersede Airworthiness Directive (AD) 2022-13-16, which applies to all GE Aviation Czech s.r.o. (GEAC) (type certificate previously held by WALTER Engines a.s., Walter a.s., and MOTORLET a.s.) Model M601D-11 engines; and AD 2022-14-12, which applies to certain GEAC Model M601D-11, M601E-11, M601E-11A, M601E-11AS, M601E- 11S, and M601F engines. AD 2022-13-16 requires revising the airworthiness limitations section (ALS) of the existing engine maintenance manual (EMM) to incorporate a visual inspection of the centrifugal compressor case for cracks. AD 2022-14-12 requires replacing the propeller shaft for Model M601F engines. AD 2022-14-12 also requires calculating the accumulated life of the propeller shaft and replacing the propeller shaft, if necessary, for model M601D-11, M601E-11, M601E-11A, M601E-11AS, and M601E-11S engines. Since the FAA issued AD 2022-13-16 and AD 2022-14-12, the manufacturer revised the ALS of the existing EMM to introduce new and more restrictive tasks and limitations, expand the applicability to all Model M601 engines, and incorporate certain requirements addressed by AD 2021-13-07 and AD 2023-01-10, which prompted this proposed AD. This proposed AD would require revising the ALS of the existing EMM and the operator's existing approved engine maintenance or inspection program, as applicable, to incorporate new and more restrictive tasks and limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Accepted Means of Compliance; Remote Identification of Unmanned Aircraft; Correction
The FAA is correcting a notice of availability (NOA) published on August 11, 2022 (87 FR 49520). In that NOA, the FAA provided an acceptable means of compliance (MOC) in accordance with a rule issued by the FAA on January 21, 2021, that went into effect on April 21, 2021. In that NOA, the FAA accepted ASTM International (ASTM) F3586-22, with additions identified, as an acceptable means, but not the only means of demonstrating compliance with the requirements for producing standard remote identification unmanned aircraft and remote identification broadcast modules. The FAA is correcting the means of compliance of ASTM F3586-22 by correcting a typographical reference error in Table 3 and clarifying a testing requirement by revising a heading and adding clarifying language, as noted in the ``Means of Compliance Accepted In This Policy'' section of this document. This document includes acceptance of previously accepted MOCs with the corrections described.
Beat the Street Interiors, Inc.-Grant of Petition for Temporary Exemption From Shoulder Belt Requirement for Side-Facing Seats on Motorcoaches
This notice grants the petition of Beat the Street Interiors, Inc. (``BTS'') for a temporary exemption from a shoulder belt requirement of Federal Motor Vehicle Safety Standard (FMVSS) No. 208, ``Occupant crash protection,'' for side-facing seats on motorcoaches. This grant permits the petitioner to install Type 1 seat belts (lap belt only) at side-facing seating positions instead of the Type 2 seat belts (lap and shoulder belts) required by FMVSS No. 208. After reviewing the petition, the agency has determined that the requested exemption is warranted to enable the petitioner to sell a vehicle whose overall level of safety or impact protection is at least equal to that of a nonexempted vehicle.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
