Department of Transportation January 31, 2022 – Federal Register Recent Federal Regulation Documents
Results 1 - 13 of 13
Semiannual Regulatory Agenda
The Chairman of the Surface Transportation Board is publishing the Regulatory Flexibility Agenda for fall 2021.
Airworthiness Directives; Airbus Helicopters
The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus Helicopters Model AS332L2 and EC225LP helicopters. This proposed AD was prompted by a discrepancy in the rotorcraft flight manual (RFM) where the rotorcraft stay-up flying capabilities for Category B operation were provided through performance data only, not as airworthiness limitations that are dependent upon on the number of passengers on board. This proposed AD would require revising the existing RFM for your helicopter, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Hélicoptères Guimbal Helicopters
The FAA proposes to supersede Airworthiness Directive (AD) 2021-02-20, which applies to certain H[eacute]licopt[egrave]res Guimbal Model Cabri G2 helicopters. AD 2021-02-20 requires initial and repetitive inspections of certain rotating and non-rotating scissor fittings, and depending on the results, replacing the affected assembly. AD 2021-02-20 also prohibits installing certain main rotor hubs (MRHs) and swashplate guides unless the initial inspection has been accomplished. Since the FAA issued AD 2021-02-20, the MRH and swashplate guide have been redesigned to include a certain part- numbered scissor fitting. This proposed AD would retain certain requirements of AD 2021-02-20, require installation of newly designed parts, provide a terminating action for the initial and repetitive inspections, and revise the applicability. This proposed AD would also extend the repetitive inspection interval and prohibit installing certain MRHs and swashplate guides. The FAA is proposing this AD to address the unsafe condition on these products.
Maserati North America, Inc., Receipt of Petition for Decision of Inconsequential Noncompliance
Maserati North America, Inc., (MNA), has determined that certain model year (MY) 2014-2021 Maserati Ghibli, Quattroporte, and Levante motor vehicles do not fully comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 208, Occupant Crash Protection. MNA filed a noncompliance report dated August 5, 2021. MNA subsequently petitioned NHTSA on August 30, 2021, and amended its petition on January 13, 2022, for a decision that the subject noncompliance is inconsequential as it relates to motor vehicle safety. This document announces receipt of MNA's petition.
Toyota Motor North America, Inc., Receipt of Petitions for Decision of Inconsequential Noncompliance
Toyota Motor North America, Inc. (TMNA) on behalf of Toyota Motor Corporation (TMC) (collectively referred to as ``Toyota'') has determined that certain replacement seat belt assemblies manufactured by Marutaka, Tokai Rika Japan, Autoliv, NSK, Joyson Safety Systems Acquisition, TRQSS, Key Safety Restraint Systems, Inc., Tokai Rika Czech, BMW Group Headquarters, Subaru Corporation, and Mazda North America Operations, and sold to Toyota dealerships as replacement equipment do not fully comply with Federal Motor Vehicle Safety Standard (FMVSS) No. 209, Seat Belt Assemblies. Toyota filed three noncompliance reports, two dated April 20, 2021, and the other dated May 4, 2021. Toyota subsequently submitted two petitions to NHTSA both dated May 14, 2021, for a decision that the subject noncompliances are inconsequential as they relate to motor vehicle safety. This notice announces receipt of Toyota's petitions.
Department Regulatory and Deregulatory Agenda; Semiannual Summary
The Regulatory Agenda is a semiannual summary of all current and projected rulemakings, reviews of existing regulations, and completed actions of the Department of Transportation. The intent of the Agenda is to provide the public with information about the Department of Transportation's regulatory activity planned for the next 12 months. It is expected that this information will enable the public to participate more effectively in the Department's regulatory process. The public is also invited to submit comments on any aspect of this Agenda.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all The Boeing Company Model 747-8F series airplanes. This proposed AD was prompted by reports of fuselage crown stringer cracking between station (STA) 740 and STA 1000, stringer (S)-7 to S-12. This proposed AD would require repetitive detailed inspections for cracking of fuselage crown stringers and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Umlaut Engineering GmbH (Previously P3 Engineering GmbH) HAFEX (Halon-Free) Hand-Held Fire Extinguishers
The FAA is adopting a new airworthiness directive (AD) for certain Umlaut Engineering GmbH (previously P3 Engineering GmbH) HAFEX (Halon-free) hand-held P3HAFEX fire extinguishers (fire extinguishers). This AD was prompted by reports of a quality control issue on certain fire extinguishers, where the spindle geometries of the fire extinguishers were found to be out of tolerance. This AD requires removing affected fire extinguishers from service. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 767-200, -300, -300F, and -400ER airplanes. This proposed AD was prompted by reports of burned Boeing Material Specification (BMS) 8-39 urethane foam, which is a material with fire-retardant properties that deteriorate with age. This proposed AD would require replacing certain BMS 8-39 foam pads with Nomex felt in certain areas, removing certain BMS 8-39 foam pads in a certain area (which includes a general visual inspection to find BMS 8-39 foam pads), and inspecting the corner seals to determine if the corner seals were replaced, and replacing affected corner seals. This proposed AD would also prohibit the installation of BMS 8-39 urethane foam seal in certain locations. The FAA is proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-8, 737-9, and 737-8200 airplanes. This AD was prompted by a determination that radio altimeters cannot be relied upon to perform their intended function if they experience interference from wireless broadband operations in the 3.7-3.98 GHz frequency band (5G C-Band), and a recent determination that, during takeoffs and landings, as a result of this interference, certain airplane systems may not properly function, resulting in longer than normal landing or rejected takeoff distances due to the effect on thrust reverser deployment, spoilers, speedbrake deployment, and increased idle thrust, regardless of the approach type or weather. This AD requires revising the limitations and operating procedures sections of the existing airplane flight manual (AFM) to incorporate limitations prohibiting the use of certain minimum equipment list (MEL) items, and to incorporate operating procedures for calculating takeoff and landing distances, when in the presence of 5G C-Band interference as identified by Notices to Air Missions (NOTAMs). The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350D, EC130B4, and EC130T2 helicopters; AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters; and Model SA-365C1, SA-365C2, SA-365N, SA-365N1, AS-365N2, and AS 365 N3 helicopters. This AD was prompted a report of increased vibration during flight. This AD requires the application of alignment markings on, and repetitive inspections of, the main rotor (MR) pitch rod upper links and, depending on findings, the accomplishment of applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Establishment of Class E Airspace; Joseph State Airport, OR
This action establishes Class E airspace extending upward from 700 feet above the surface of the earth at Joseph State Airport, Joseph, OR. The establishment of airspace supports the airport's transition from visual flight rules to instrument flight rule (IFR) operations and ensures the safety and management of IFR operations within the National Airspace System.
Establishment of Class E Airspace; Monticello Airport, UT
This action establishes Class E airspace extending upward from 700 feet above the surface of the earth at Monticello Airport, Monticello, UT. The establishment of airspace supports the airport's transition from visual flight rules to instrument flight rule (IFR) operations and ensures the safety and management of IFR operations within the National Airspace System.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.