Department of Transportation November 2015 – Federal Register Recent Federal Regulation Documents

The purpose of this NOI is to update the notice that was issued in the Federal Register Vol. 79 No. 221, Monday, November 17, 2014, Notices. The FHWA is issuing this revised notice to advise the public that FHWA and WisDOT will be preparing a Tier 1 Environmental Impact Statement (EIS) for proposed transportation improvements along the Interstate (I)-90/94 corridor, from United States Highway (US) 12/ Wisconsin State Highway (WIS) 16 Interchange to the I-39/WIS 78 interchange in Juneau, Sauk, and Columbia Counties in Wisconsin.

We propose to adopt a new airworthiness directive (AD) for all Embraer S.A. Model ERJ 170 airplanes; and all Embraer S.A. Model ERJ 190-100 STD, -100 LR, -100 IGW, -200 STD, -200 LR, and -200 IGW airplanes. This proposed AD was prompted by reports of cracks in certain engine low-stage bleed check valves. This proposed AD would require replacing the air management system (AMS) controller operation program of the AMS controller processor boards, and replacement of the current low-stage bleed check valve and associated seals. We are proposing this AD to prevent failure of the low-stage bleed check valve, which could result in dual engine in-flight shutdown.

We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A318, A319, A320, and A321 series airplanes. This proposed AD was prompted by reports of cracking of the aft fixed fairing (AFF) of the pylons due to fatigue damage of the structure. This proposed AD would require repetitive inspections for damage and cracking of the AFF of the pylons, and repair if necessary. We are proposing this AD to detect and correct damage and cracking of the AFF of the pylons, which could result in detachment of a pylon and consequent reduced structural integrity of the airplane.

We propose to adopt a new airworthiness directive (AD) for all Airbus Model A318-111 and -112 airplanes; Model A319-111, -112, -113, - 114, and -115 airplanes; Model A320-211, -212, and -214 airplanes; and Model A321-111, -112, -211, -212, and -213 airplanes. This proposed AD was prompted by an evaluation by the design approval holder (DAH) indicating that the forward engine mounts are subject to widespread fatigue damage (WFD). This proposed AD would require repetitive detailed inspections of the right and left forward engine mounts, and corrective action if necessary. These inspections are required by AD 2015-05-02. This proposed AD would reduce the compliance times for those inspections. We are proposing this AD to detect and correct fatigue cracking in the forward engine mounts, which could result in reduced structural integrity of the airplane and could lead to in- flight loss of an engine, possibly resulting in reduced controllability of the airplane.

FRA is issuing this notice to advise the public that it intends to grant the Illinois Department of Transportation (IDOT) a waiver from FRA's Buy America requirement for the use of 250 Sure Close gate hinges, which are manufactured in Italy. FRA believes a waiver is appropriate because, despite IDOT's best efforts to develop a domestic source for these hinges, domestically-produced gate hinges for pedestrian crossings meeting IDOT's safety specifications and schedule needs remain unavailable in the United States.

This action amends Class E Airspace at Elmira/Corning Regional Airport, Elmira, NY; Ithaca Tompkins Regional Airport, Ithaca, NY; and Duchess County Airport, Poughkeepsie, NY, by eliminating the Notice to Airmen (NOTAM) part time status of the Class E surface airspace designated as an extension at each airport. This action also updates the geographic coordinates of each airport to coincide with the FAA's database, and recognizes the airport name for Ithaca Tompkins Regional Airport. This is an administrative change to coincide with the FAA's aeronautical database.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes, CL-600-2C10 (Regional Jet Series 700, 701 & 702) airplanes, CL-600-2D15 (Regional Jet Series 705) airplanes, CL-600-2D24 (Regional Jet Series 900) airplanes, and CL-600-2E25 (Regional Jet Series 1000) airplanes. This AD requires repetitive detailed inspections of the cage assembly, window louver panel assemblies (WLPAs), and blowout panels (BOPs), and corrective action if necessary. This AD was prompted by reports of several cases of damaged or detached decompression WLPAs and BOPs. We are issuing this AD to detect and correct damaged and detached WLPAs and BOPs. A detached WLPA or BOP could delay smoke detection in the cargo compartment, and in the event of a cargo compartment fire, this could lead to an uncontrolled cargo compartment fire.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

As authorized by 46 U.S.C. 12121, the Secretary of Transportation, as represented by the Maritime Administration (MARAD), is authorized to grant waivers of the U.S.-build requirement of the coastwise laws under certain circumstances. A request for such a waiver has been received by MARAD. The vessel, and a brief description of the proposed service, is listed below.

The Maritime Administration (MARAD) is issuing this request for applications for eligible vessels to potentially enroll in one or more MSP Operating Agreements in accordance with the provisions of the Maritime Security Act of 2003, Public Law 108-136, div. C, title XXXV, as amended by Section 3508 of the National Defense Authorization Act for Fiscal Year (FY) 2013, Public Law 112-239, (NDAA 2013). The Maritime Security Program (MSP) maintains a fleet of active, commercially-viable, privately-owned vessels to meet national defense and other security requirements and to maintain a United States presence in international commercial shipping. This request for applications provides, among other things, application criteria and a deadline for submitting applications for potential vessel enrollment in the MSP.

FMCSA announces receipt of 7 applications for exemptions from the cardiovascular standard [49 CFR 391.41(b)(4)]. These 7 individuals are requesting an exemption due to the presence of implantable cardioverter defibrillators (ICD) as a result of their underlying cardiac condition. If granted, the exemptions would enable these individuals with ICDs to operate commercial motor vehicles (CMVs) in interstate commerce for up to 2 years.

FMCSA announces receipt of applications from 44 individuals for exemption from the prohibition against persons with insulin-treated diabetes mellitus (ITDM) operating commercial motor vehicles (CMVs) in interstate commerce. If granted, the exemptions would enable these individuals with ITDM to operate CMVs in interstate commerce.

We propose to supersede Airworthiness Directive (AD) 2006-10- 16, which applies to all The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. AD 2006-10-16 requires, for certain airplanes, repetitive inspections for cracking of the outboard and center sections of the horizontal stabilizer, and repair if necessary. For certain other airplanes, AD 2006-10-16 requires a detailed inspection to determine the type of fasteners, and related investigative actions and repair if necessary. Since we issued AD 2006- 10-16, additional cracking was found in the splice plates, hinge fittings, terminal fittings, the upper skin of the outboard and center sections, and the rear spar webs before reaching the inspection interval specified in AD 2006-10-16. Cracked and fractured Maraging steel fasteners were also found. This proposed AD would reduce the compliance time for certain inspections and would add repetitive inspections for cracking of the splice plates, hinge fittings, terminal fittings, the upper skin of the outboard and center sections, and the rear spar webs in Zone B. This proposed AD would also add an inspection to determine whether fasteners are magnetic in Zone C, repetitive ultrasonic inspections for cracking and fractures of affected fasteners, and related investigative and corrective actions if necessary. This proposed AD would also add an optional modification, which would terminate certain repetitive inspections, and would add post-modification inspections and corrective action if necessary. We are proposing this AD to detect and correct this cracking, which could lead to reduced structural capability of the outboard and center sections of the horizontal stabilizer and could result in loss of control of the airplane.

We propose to adopt a new airworthiness directive (AD) for certain Airbus Model A318, A319, and A320 series airplanes. This proposed AD was prompted by reports of an operator finding chafing damage on the fuselage skin at the bottom of certain frames, underneath the fairing structure. This proposed AD would require a repetitive detailed inspection for damage on the fuselage skin at certain frames, and applicable related investigative and corrective actions. We are proposing this AD to detect and correct damage to the fuselage skin, which could lead to crack initiation and propagation, possibly resulting in reduced structural integrity of the fuselage.

We propose to supersede Airworthiness Directive (AD) 2011-23- 05, which applies to certain The Boeing Company Model 737-300, -400, and -500 series airplanes. AD 2011-23-05 currently requires repetitive inspections for cracking of the 1.04-inch nominal diameter wire penetration hole, and applicable related investigative and corrective actions. Since we issued AD 2011-23-05, an evaluation by the design approval holder (DAH) indicates that the fuselage frames and frame reinforcements are subject to widespread fatigue damage (WFD). This proposed AD would add new inspection areas, a modification that terminates certain inspections, post-modification inspections, and repair if necessary. We are proposing this AD to detect and correct fatigue cracking of the fuselage frames and frame reinforcements, which could result in reduced structural integrity of the airplane.

We propose to supersede Airworthiness Directive (AD) 2004-19- 11 for certain Airbus Model 320 series airplanes. AD 2004-19-11 currently requires modification of the inner rear spar web of the wing, cold expansion of the attachment holes of the forward pintle fitting and the actuating cylinder anchorage of the main landing gear (MLG), repetitive ultrasonic inspections for cracking of the rear spar of the wing, and corrective action if necessary. AD 2004-19-11 also provides optional terminating action for the repetitive inspections. Since we issued AD 2004-19-11, we have determined that the terminating action is necessary to address the unsafe condition. This proposed AD is intended to complete certain mandated programs intended to support the airplane reaching its limit of validity (LOV) of the engineering data that support the established structural maintenance program. This proposed AD would retain the requirements of AD 2004-19-11 and would require the previously optional terminating action. We are proposing this AD to prevent fatigue cracking of the inner rear spar, which may lead to reduced structural integrity of the wing and the MLG.

In accordance with the procedures governing the application for, and the processing of, special permits from the Department of Transportation's Hazardous Material Regulations (49 CFR part 107, subpart B), notice is hereby given that the Office of Hazardous Materials Safety has received the application described herein. Each mode of transportation for which a particular special permit is requested is indicated by a number in the ``Nature of Application'' portion of the table below as follows: 1Motor vehicle, 2Rail freight, 3Cargo vessel, 4Cargo aircraft only, 5Passenger-carrying aircraft.

In accordance with the requirements of 49 U.S.C. 5117(c), PHMSA is publishing the following list of special permit applications that have been in process for 180 days or more. The reason(s) for delay and the expected completion date for action on each application is provided in association with each identified application.

We are adopting a new airworthiness directive (AD) for SOCATA Model TB 9, TB 10, TB 20, TB 21, and TB 200 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as corrosion of the horizontal stabilizer. We are issuing this AD to require actions to address the unsafe condition on these products.

We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by reports that cracks can occur in a frame of the tail section on certain airplanes. This AD requires a one-time detailed inspection of the oblique frame 67-2 for any cracking, and repair if necessary. We are issuing this AD to detect and correct such cracking, which could lead to failure of the oblique frame 67-2, and consequent loss of the structural integrity of the tail section.

This action proposes to modify Class D airspace, Class E surface area airspace, Class E surface area airspace designated as an extension, and Class E airspace extending upward from 700 feet above the surface at Walla Walla Regional Airport, Walla Walla, WA. After a review of the airspace, the FAA found it necessary to amend the airspace area for the safety and management of Instrument Flight Rules (IFR) operations for arriving and departing aircraft at the airport. This action would also update the geographic coordinates of Walla Walla Regional Airport in the respective Class D and E airspace areas above.