Department of Transportation August 9, 2012 – Federal Register Recent Federal Regulation Documents

Utilimaster Corporation (Utilimaster),\1\ has determined that certain model year 2009-2011 Utilimaster walk-in van-type trucks manufactured between September 1, 2009 and December 22, 2011 do not comply with paragraph S4.2.1 of Federal Motor Vehicle Safety Standard (FMVSS) No. 206, Door Locks and Door Retention Components. Utilimaster filed an appropriate report dated December 30, 2011, pursuant to 49 CFR part 573, Defect and Noncompliance Responsibility and Reports.

General Motors, LLC (GM) \1\ has determined that certain model year 2012; Cadillac SRX, Chevrolet Equinox, GMC Terrain and Saab 9-4x multipurpose passenger vehicles, and Chevrolet Cruze passenger cars, do not fully comply with paragraph S19.2.2 of Federal Motor Vehicle Safety Standard (FMVSS) No. 208, Occupant Crash Protection. GM has filed an appropriate report dated September 6, 2011, pursuant to 49 CFR part 573, Defect and Noncompliance Responsibility and Reports.

As required by the Paperwork Reduction Act of 1995, 44 U.S.C. 3501-3519 (PRA), the Surface Transportation Board (STB or Board) gives notice of its intent to seek from the Office of Management and Budget (OMB) approval of the information collections required under 49 U.S.C. 10904-05 and 10907, and 16 U.S.C. 1247(d). Under these statutory provisions, the Board administers programs designed to preserve railroad service or rail rights-of-way. When a line is proposed for abandonment, affected shippers, communities, or other interested persons may seek to preserve rail service by filing with the Board: an offer of financial assistance (OFA) to subsidize or purchase a rail line for which a railroad is seeking abandonment (49 U.S.C. 10904), including a request for the Board to set terms and conditions of the financial assistance; a request for a public use condition (section 10905); or a trail-use request (16 U.S.C. 1247(d)). Similarly, when a line is placed on a system diagram map identifying it as an anticipated or potential candidate for abandonment, affected shippers, communities, or other interested persons may seek to preserve rail service by filing with the Board a feeder line application to purchase the identified rail line (section 10907). Additionally, the railroad owning the rail line subject to abandonment must, in some circumstances, provide information to the applicant or offeror. The Board previously published a notice about this collection in the Federal Register on February 10, 2012, at 77 FR 7236-37 (60-day notice). That notice allowed for a 60- day public review and comment period. No comments were received. The information collection for which approval is sought is described in detail below. Comments may now be submitted to OMB concerning: (1) The accuracy of the Board's burden estimates; (2) ways to enhance the quality, utility, and clarity of the information collected; (3) ways to minimize the burden of the collection of information on the respondents, including the use of automated collection techniques or other forms of information technology, when appropriate; and (4) whether this collection of information is necessary for the proper performance of the functions of the Board, including whether the collection has practical utility.

We are revising an earlier proposed airworthiness directive (AD) for certain The Boeing Company Model 767 airplanes. That NPRM proposed to require drilling a drain hole in the flanged tubes for certain elevator control cable aft pressure seals; doing repetitive inspections for dirt, loose particles, or blockage of the flanged tube and drain hole for the pressure seals, and corrective action if necessary; replacing the aft air-intake duct assembly with a new or modified assembly and installing a dripshield; and installing gutters on the horizontal stabilizer center section and modifying the side brace fittings. That NPRM was prompted by reports of stiff operation of the elevator pitch control system and jammed elevator controls. This action revises that NPRM by proposing to require replacement of pressure seal assemblies, rather than the proposed drilling of drain holes; revising a certain compliance time and inspection type; adding certain optional actions; and revising the applicability. We are proposing this supplemental NPRM to prevent moisture from collecting and freezing on the elevator control system components, which could limit the ability of the flightcrew to make elevator control inputs and result in reduced controllability of the airplane. Since these actions impose an additional burden over that proposed in the previous NPRM, we are reopening the comment period to allow the public the chance to comment on these proposed changes.