Department of Transportation September 19, 2006 – Federal Register Recent Federal Regulation Documents
Results 1 - 6 of 6
Airworthiness Directives; Cirrus Design Corporation Models SR20 and SR22 Airplanes
We are adopting a new airworthiness directive (AD) that supersedes AD 2005-17-19, which applies to certain Cirrus Design Corporation (CDC) Models SR20 and SR22 airplanes. AD 2005-17-19 currently requires you to measure and adjust the crew seat break-over bolts and to replace the crew seat recline locks on both crew seats. Since we issued AD 2005-17-19, CDC developed new crew seat break-over pins to replace the old crew seat break-over bolts. Consequently, this AD retains the action from AD 2005-17-19 of replacing the crew seat recline locks on both seats and adds the action of replacing the crew seat break-over bolts with the new crew seat break-over pins on both seats. We are issuing this AD to prevent the crew seats from folding forward during emergency landing dynamic loads with consequent occupant injury.
Airworthiness Directives; Raytheon Aircraft Company Model B300 Airplanes
We are adopting a new airworthiness directive (AD) for certain Raytheon Aircraft Company (RAC) Model B300 airplanes. This AD requires you to modify the cabin passenger seats by installing a modification kit on each passenger seat, removing the existing technical standard order (TSO) label, and re-identifying each modified passenger seat assembly with a new part number. This AD results from the seats not meeting the ultimate load requirements of 14 CFR part 23 during structural testing of the seat with design changes. We are issuing this AD to prevent the passenger seats from failing during emergency landing conditions when high inertial loadings occur. Passenger seat failure may result in occupant injury.
Airworthiness Directives; Airbus Model A330, A340-200, and A340-300 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A330, A340-200, and A340-300 airplanes. This AD requires replacing the attachment landing assemblies of certain blow- down panels of the wing leading edges with new, improved landing assemblies. This AD results from several reports of full or partial loss of certain blow-down panels of the wing leading edges during flight. We are issuing this AD to prevent damage to the airplane and hazards to persons or property on the ground.
Airworthiness Directives; Stemme GmbH & Co. KG Model STEMME S10-VT Sailplanes
The FAA is adopting a new airworthiness directive (AD) for certain Stemme GmbH & Co. KG Model STEMME S10-VT sailplanes. This AD requires you to do a one-time inspection of all exhaust bends (each cylinder 1 to 4) in the area of the curvature bend near the cylinder flange, replace any damaged exhaust pipes found, and recondition the heat protection wrapping. This AD results from deformations and cracks found at an exhaust bend during maintenance work. We are issuing this AD to detect and correct cracks in the exhaust pipes. Damaged exhaust pipes could cause exhaust gases to expand into the engine compartment and/or carbon monoxide (CO) to leak into the cockpit section.
Application of Swift Air, LLC for Certificate Authority
The Department of Transportation is directing all interested persons to show cause why it should not issue orders finding Swift Air, LLC fit, willing, and able, and awarding it certificates of public convenience and necessity to engage in interstate and foreign charter air transportation of persons, property and mail.
Noise Exposure Map Notice; Receipt of Noise Compatibility Program and Request for Review; Danbury Municipal Airport; Danbury, CT
The Federal Aviation Administration (FAA) announces its determination that the noise exposure map for Danbury Municipal Airport, as submitted by the City of Danbury under the provisions of Title I of the Aviation Safety and Noise Abatement Act of 1979 (Pub. L. 96-193) and 14 CFR Part 150, is in compliance with applicable requirements. The FAA also announces that it is reviewing a proposed noise compatibility program that was submitted for Danbury Municipal Airport under Part 150 in conjunction with the noise exposure map, and that this program will be approved or disapproved on or before March 9, 2007.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
