Department of Transportation September 16, 2005 – Federal Register Recent Federal Regulation Documents

Notice of Submission Deadline for International Slots for the Summer 2006 Scheduling Season
Document Number: X05-10916
Type: Notice
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
On October 1, 1999, the FAA amended the regulations governing takeoff and landing slots and slot allocation procedures at certain High Density Traffic Airports as a result of the ``Open Transborder'' Agreement between the Government of the United States and the Government of Canada. One element of this final rule established that the deadline for submission of requests for international slots will be published in a Federal Register notice for each scheduling season. The purpose of the amendment is for the FAA deadline for international slots requests to coincide with the International Air Transport Association deadline for submission of international requests. In accordance with this amendment, the FAA announces in this notice that the deadline for submitting requests for international slots at John F. Kennedy International Airport (JFK) for allocation under 14 CFR 93.217 is October 13, 2005. Additionally,the FAA has designated Chicago's O'Hare International Airport (O'Hare) as a Level 2, Schedules Facilitated Airport under the IATA Guidelines. As such, the FAA requests carriers intending to conduct international service to O'Hare submit their intended schedules following the same procedures used for submitting requests for slots at JFK.
Santa Clara Valley Transportation Authority-Abandonment Exemption-in Santa Clara and Alameda Counties, CA
Document Number: 05-18570
Type: Notice
Date: 2005-09-16
Agency: Surface Transportation Board, Department of Transportation
Proposed Agency Information Collection Activities; Comment Request
Document Number: 05-18487
Type: Notice
Date: 2005-09-16
Agency: Federal Railroad Administration, Department of Transportation
In accordance with the Paperwork Reduction Act of 1995 and its implementing regulations, the Federal Railroad Administration (FRA) hereby announces that it is seeking renewal of the following currently approved information collection activities. Before submitting these information collection requirements (ICRs) for clearance by the Office of Management and Budget (OMB), FRA is soliciting public comment on specific aspects of the activities identified below.
Railroad Safety Advisory Committee; Notice of Meeting
Document Number: 05-18486
Type: Notice
Date: 2005-09-16
Agency: Federal Railroad Administration, Department of Transportation
FRA announces the next meeting of the RSAC, a Federal Advisory Committee that develops railroad safety regulations through a consensus process. The RSAC meeting topics include a briefing on the Safe, Accountable, Flexible, Efficient Transportation Equity Act: A Legacy for Users; the National Rail Safety Action Plan; the new precess for rail safety oversight; Congressional reports; and the railroad industry's response to natural disasters. Status reports will be given on the Passenger Safety, Railroad Operating Rules, Roadway Worker, and other active working groups. The Committee will be asked to vote on the Passenger Safety Working Group (1) Emergency Preparedness recommendations for a proposed rescue window access time line, (2) Mechanical recommendations and (3) Crashworthiness recommendations for the notice of proposed rulemaking.
Petition for Waiver of Compliance
Document Number: 05-18485
Type: Notice
Date: 2005-09-16
Agency: Federal Railroad Administration, Department of Transportation
Petition for Waiver of Compliance
Document Number: 05-18484
Type: Notice
Date: 2005-09-16
Agency: Federal Railroad Administration, Department of Transportation
Petition for Waiver of Compliance
Document Number: 05-18483
Type: Notice
Date: 2005-09-16
Agency: Federal Railroad Administration, Department of Transportation
Petition for Waiver of Compliance
Document Number: 05-18482
Type: Notice
Date: 2005-09-16
Agency: Federal Railroad Administration, Department of Transportation
Public Meeting To Discuss the Implementation of the North American Standard for Cargo Securement; Correction
Document Number: 05-18479
Type: Notice
Date: 2005-09-16
Agency: Federal Motor Carrier Safety Administration, Department of Transportation
The Federal Motor Carrier Safety Administration (FMCSA) published in the Federal Register on August 31, 2005 (70 FR 51857) a notice of a public meeting concerning the implementation of the North American Standard for Protection Against Shifting or Falling Cargo. The meeting was scheduled to be held on September 29-30, 2005 at the Beau Rivage Resort in Biloxi, Mississippi. However, due to the devastation caused by Hurricane Katrina, the location of this meeting has been moved from Biloxi, Mississippi, to the Hyatt Regency Indianapolis which is located at One South Capitol Avenue, Indianapolis IN 46204. Reservations can be made by contacting the Hyatt Regency Indianapolis by phone (317) 632-1234 or by fax (317) 616-6299.
Release of Waybill Data
Document Number: 05-18414
Type: Notice
Date: 2005-09-16
Agency: Surface Transportation Board, Department of Transportation
Application of PM Air, LLC For Certificate Authority
Document Number: 05-18411
Type: Notice
Date: 2005-09-16
Agency: Office of the Secretary, Department of Transportation
The Department of Transportation is directing all interested persons to show cause why it should not issue an order finding PM Air, LLC fit, willing, and able, and awarding it a certificate of public convenience and necessity to engage in interstate scheduled air transportation of persons, property, and mail operating no more than two aircraft in scheduled service under Part 135 of the Federal Aviation Regulations.
Airworthiness Directives; Boeing Model 747-200C and -200F Series Airplanes
Document Number: 05-18403
Type: Proposed Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 747-200C and -200F series airplanes. The existing AD currently requires repetitive inspections to find fatigue cracking in the upper chord of the upper deck floor beams, and repair if necessary. For certain airplanes, the existing AD also provides an optional repair/modification, which extends certain repetitive inspection intervals. This proposed AD would reduce the compliance time for all initial inspections and reduce the repetitive interval for a certain inspection. This proposed AD is prompted by new reports of cracks in the upper deck floor beams occurring at lower flight cycles. We are proposing this AD to find and fix cracking in certain upper deck floor beams. Such cracking could extend and sever floor beams at a floor panel attachment hole location and could result in rapid decompression and loss of controllability of the airplane.
Airworthiness Directives; British Aerospace Model BAC 1-11 200 and 400 Series Airplanes
Document Number: 05-18402
Type: Proposed Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for all British Aerospace Model BAC 1-11 200 and 400 series airplanes. This proposed AD would require revising the airplane flight manual (AFM) to contain applicable AFM amendments, which advise the flightcrew of information pertaining to safely operating the fuel system. The proposed AD would also require revising the FAA-approved maintenance program to include certain repetitive maintenance tasks intended to improve the safety of the fuel system. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to prevent potential ignition sources inside the fuel system, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; McDonnell Douglas Model DC-8-33, DC-8-51, DC-8-53, DC-8-55, DC-8F-54, DC-8F-55, DC-8-63, DC-8-62F, DC-8-63F, DC-8-71, DC-8-73, DC-8-71F, DC-8-72F, and DC-8-73F Airplanes
Document Number: 05-18401
Type: Proposed Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain transport category airplanes, identified above. This proposed AD would require repetitive inspections for cracks of the doorjamb corners of the main cargo door, and repair if necessary. This proposed AD also provides an optional preventive modification that extends certain repetitive intervals. This proposed AD results from reports of cracks in the fuselage skin at the corners of the doorjamb for the main cabin cargo door. We are proposing this AD to detect and correct fatigue cracks in the fuselage skin, which could result in rapid decompression of the airplane.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-300, 747-400, 747-400D, and 747SR Series Airplanes
Document Number: 05-18400
Type: Proposed Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for all Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747- 200C, 747-300, 747-400, 747-400D, and 747SR series airplanes. This proposed AD would require a one-time inspection to determine whether any steel doubler (small or large) is installed at the lower forward and upper aft corners of the fuselage cutout at main entry doors (MEDs) number 3. Depending on the results of this inspection, this proposed AD also would require repetitive inspections for cracks of the skin, bearstrap, and small steel doubler (if installed) at the applicable corner or corners of the fuselage cutouts, and related investigative/ corrective actions if necessary. This proposed AD also would provide the optional terminating action for the repetitive inspections of installing a large steel doubler at the affected corners. This proposed AD is prompted by reports of cracks in the skin and bearstrap at the upper aft corner and at the lower forward corner of the fuselage cutout at MEDs number 3. We are proposing this AD to detect and correct cracks in the skin, bearstrap, and small steel doubler (if installed), which could propagate and result in rapid decompression of the airplane.
Standard Instrument Approach Procedures, Weather Takeoff Minimums; Miscellaneous Amendments
Document Number: 05-18376
Type: Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
This amendment establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and/or Weather Takeoff Minimums for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, addition of new obstacles, or changes in air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Penn Eastern Rail Lines, Inc.-Operation Exemption-Expressway 95 Industrial Park
Document Number: 05-18352
Type: Notice
Date: 2005-09-16
Agency: Surface Transportation Board, Department of Transportation
False and Misleading Statements Regarding Aircraft Products, Parts, Appliances and Materials
Document Number: 05-18343
Type: Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
This final rule amends FAA regulations to create additional rules banning certain false or misleading statements about type- certificated products, and products, parts, appliances and materials that may be used on type-certificated products. This action is necessary to help prevent people from representing that these items are suitable for use on type-certificated products when in fact they may not be. These rules are intended to provide assurance that aircraft owners and operators, and persons who maintain aircraft, have factual information on which to determine whether a product, part, appliance or material may be used in a given type-certificated product application.
Advanced Qualification Program
Document Number: 05-18342
Type: Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
This action codifies the requirements of the Advanced Qualification Program (AQP). Currently, the AQP requirements are in a Special Federal Aviation Regulation that expires on October 2, 2005. The AQP will continue as an alternative regulatory program for airlines seeking more flexibility in training than the traditional training program allows. The intended effect of this rule is to codify the AQP as a permanent, alternative method of compliance with the FAA's training requirements for carriers.
Airworthiness Directives; Lycoming Engines (Formerly Textron Lycoming) AEIO-360, IO-360, O-360, LIO-360, LO-360, AEIO-540, IO-540, O-540, and TIO-540 Series Reciprocating Engines
Document Number: 05-18323
Type: Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Lycoming Engines (formerly Textron Lycoming) AEIO-360, IO-360, O-360, LIO-360, LO-360, AEIO-540, IO-540, O-540, and TIO-540 series reciprocating engines rated at 300 horsepower (HP) or lower. This AD requires replacing certain crankshafts. This AD results from reports of 12 crankshaft failures in Lycoming 360 and 540 series engines rated at 300 HP or lower. We are issuing this AD to prevent failure of the crankshaft, which could result in total engine power loss, in-flight engine failure, and possible loss of the aircraft.
Airworthiness Directives; Turbomeca Arrius 2 F Turboshaft Engines
Document Number: 05-18322
Type: Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for Turbomeca Arrius 2 F turboshaft engines. This AD requires removing from service certain serial number (SN) fuel control units (FCUs) or replacing the constant delta pressure diaphragm in those FCUs. This AD results from a report of an accident in July 2005 involving a Eurocopter EC120B helicopter. We are issuing this AD to prevent an uncommanded engine in-flight shutdown on a single-engine helicopter, resulting in a forced autorotation landing or an accident.
Airworthiness Directives; McDonnell Douglas Model DC-9-14, DC-9-15, and DC-9-15F Airplanes; and McDonnell Douglas Model DC-9-20, DC-9-30, DC-9-40, and DC-9-50 Series Airplanes
Document Number: 05-18314
Type: Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all transport category airplanes listed above. This AD requires repetitive inspections for cracks of the main landing gear (MLG) shock strut cylinder, and related investigative and corrective actions if necessary. This AD results from two reports of a collapsed MLG and a report of cracks in two MLG cylinders. We are issuing this AD to detect and correct fatigue cracks in the shock strut cylinder of the MLG, which could result in a collapsed MLG during takeoff or landing, and possible reduced structural integrity of the airplane.
Airworthiness Directives; Boeing Model 747 Airplanes
Document Number: 05-18313
Type: Rule
Date: 2005-09-16
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747 airplanes. This AD requires repetitive inspections of the dual side braces (DSBs), underwing midspar fittings, and associated parts; other specified actions; and corrective actions if necessary. This AD also provides an optional terminating action for the inspections and other specified actions. This AD is prompted by reports of corroded, migrated, and rotated bearings for the DSBs in the inboard and outboard struts, a report of a fractured retainer for the eccentric bushing for one of the side links of a DSB, and reports of wear and damage to the underwing midspar fitting on the outboard strut. We are issuing this AD to prevent the loss of a DSB or underwing midspar fitting load path, which could result in the transfer of loads and motion to other areas of a strut, and possible separation of a strut and engine from the airplane during flight.
Norfolk Southern Railway Company-Consolidation of Operations-CSX Transportation, Inc. (Petition for Supplemental Order)
Document Number: 05-18246
Type: Notice
Date: 2005-09-16
Agency: Surface Transportation Board, Department of Transportation
On August 17, 2005, CSX Transportation, Inc. (CSXT) and Norfolk Southern Railway Company (NSR) filed with the Surface Transportation Board (Board) a petition (the Joint Petition) for a supplemental order authorizing the modification of one aspect of a series of transactions that the Board's predecessor, the Interstate Commerce Commission (ICC), approved in 1993. The contemplated modification is to have CSXT, rather than NSR, perform switching services for both carriers in the Newberry, SC area.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.