Department of Transportation March 21, 2005 – Federal Register Recent Federal Regulation Documents
Results 1 - 15 of 15
Physical Qualification of Drivers; Medical Examination and Certification; Exemption Application-National Cooperative Refinery Association and Jayhawk Pipeline, LLC
FMCSA received an application from the National Cooperative Refinery Association (``NCRA'') and its affiliate Jayhawk Pipeline, LLC, for an exemption from the driver's physical qualification rule which requires drivers who operate commercial motor vehicles (CMVs) in interstate commerce to be medically examined and certified every 24 months. NCRA states an exemption is needed to extend the expiration of the qualification date up to eight days for 130 of its drivers who were qualified to operate a CMV on various dates in April of 2004. If granted, an exemption would allow NCRA to schedule its drivers' medical examinations in April of 2006, after the expiration of their physical qualification certification.
Advisory Circular 33.75-1, Guidance Material for 14 CFR 33.75, Safety Analysis.
This notice announces the issuance of Advisory Circular (AC) 33.75-1, Guidance Material for 14 CFR 33.75, Safety Analysis. This AC sets forth acceptable methods of compliance with the safety analysis requirements of 14 CFR 33.75.
Modification of Class E Airspace; Rolla, MO
This document confirms the effective date of the direct final rule which revises Class E airspace at Rolla, MO.
Rules of Practice in FAA Civil Penalty Actions
The FAA amended the procedural regulations governing the assessment of civil penalties against persons other than individuals acting as pilots, flight engineers, mechanics or repairmen in a notice published in the Federal Register on February 18, 2005. We explained in the preamble of that notice that we were amending the procedural rules to provide the FAA Hearing Docket's new address and new instructions on filing of documents. We inadvertently failed to amend the rule about filing an appeal, to include the new address informtion. We are now making that inadvertently omitted amendment.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-300, 747SP, and 747SR Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-300, 747SP, and 747SR series airplanes. That AD currently requires one-time inspections for cracking in certain upper deck floor beams and follow-on actions. This new AD expands the existing inspection area and requires inspecting fastener holes in certain areas of airplanes modified previously, and taking corrective actions if necessary. This action also defines new sources for instructions for repairs and post-modification/repair inspections. This AD is prompted by reports of fatigue cracking of the upper chord of certain upper deck floor beams. We are issuing this AD to find and fix cracking in certain upper deck floor beams, which could extend and sever floor beams adjacent to the body frame and result in rapid depressurization and loss of controllability of the airplane.
Airworthiness Directives; Boeing Model 767-200, -300, and -300F Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-200, -300, and -300F series airplanes. This AD requires replacing the inboard fairing seal common to the vapor barrier seal of each strut assembly. This AD is prompted by discovery during production that a section of vapor barrier seal was missing from the spar web cavities of the upper aft struts of both wings. We are issuing this AD to prevent flammable fluids from leaking onto parts of a hot exhaust system of a shut-down engine of an airplane on the ground, which could result in ignition of the flammable fluids and an uncontained fire. This could also lead to an emergency evacuation of the airplane and possible injury to passengers.
Airworthiness Directives; Boeing Model 747-100, -100B, -100B SUD, -200B, and -300 Series Airplanes; and Model 747SR and 747SP Series Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 747-100, -100B, -100B SUD, -200B, and -300 series airplanes; and Model 747SR and 747SP series airplanes. That AD currently requires repetitive inspections to detect fatigue cracking in the upper deck floor beams located at certain body stations, and repair, if necessary. This new AD lowers the threshold for the existing inspections and requires new repetitive inspections of previously repaired areas, and repair if necessary. This AD is prompted by the results of an additional detailed analysis that indicate fatigue cracks can initiate sooner than has previously been observed. We are issuing this AD to prevent failure of the upper deck floor beams at certain body stations due to fatigue cracking, which could result in rapid decompression and reduced controllability of the airplane.
Airworthiness Directives; The Cessna Aircraft Company Models 172R, 172S, 182T, and T182T Airplanes
The FAA is adopting a new airworthiness directive (AD) to revise emergency AD 2005-05-53 for The Cessna Aircraft Company (Cessna) Models 172R, 172S, 182T, and T182T airplanes. This AD contains the same information as emergency AD 2005-05-53 R1 and publishes the action in the Federal Register. It requires you to do a one-time detailed inspection of the flight control system, correct installations that do not conform to type design, and repair any damage. This AD is the result of flight control system problems found on airplanes within Cessna's control that could also exist on airplanes produced and delivered within a certain time period. We are issuing this AD to prevent loss of airplane control due to incorrect or inadequate rigging of critical flight systems.
Airworthiness Directives; Fairchild Aircraft, Inc. SA226 and SA227 Series Airplanes
The FAA is adopting a new Airworthiness Directive (AD) to supersede AD 99-06-02, which currently applies to certain Fairchild Aircraft (Fairchild) SA226 and SA227 series airplanes. AD 99-06-02 requires you to repetitively inspect the wing spar center web cutout on both wings for cracks between Wing Station (WS) 8 and WS 17.5. That AD also requires you to repair any area found cracked before further flight. The repair will eliminate the need for the repetitive inspections on that particular wing spar. Since that AD became effective, we have determined that we inadvertently omitted certain Model SA227-CC/DC airplane serial numbers from the applicability. This AD retains the actions of AD 99-06-02 and adds additional Model SA227- CC/DC airplanes to the Applicability section. The actions specified in this AD are intended to detect and correct fatigue cracking of the wing spar center web cutout area, which could result in structural failure of the wing spar. This could lead to loss of control of the airplane.
Airworthiness Directives; the Cessna Aircraft Company Models 402C and 414A Airplanes
The FAA is adopting a new airworthiness directive (AD) to supersede emergency AD 2005-05-51 and AD 2000-23-01 for The Cessna Aircraft Company (Cessna) Models 402C and 414A airplanes. This AD contains the same information as emergency AD 2005-05-52 and publishes the action in the Federal Register. It requires you to eddy current inspect the forward wing spars and visually inspect the aft and auxiliary spars. This AD is the result of extensive cracks found on three wing spars of the affected airplanes. We are issuing this AD to detect and correct cracking in the wing spars before the cracks grow to failure. Such a wing failure could result in the wing separating from the airplane with consequent loss of control of the airplane.
Airworthiness Directives; General Electric Company (GE) CF6-80A1/A3 and CF6-80C2A Series Turbofan Engines, Installed on Airbus Industrie A300-600 and A310 Series Airplanes
The FAA is superseding an existing airworthiness directive (AD) for GE CF6-80A1/A3 and CF6-80C2A series turbofan engines. That AD currently requires completing one of the following actions before further flight: Performing a directional pilot valve (DPV) pressure check for leakage, and, if necessary, replacing the DPV assembly with a serviceable assembly, or Replacing the DPV assembly with a serviceable assembly, or Deactivating the thrust reverser, and revising the FAA- approved airplane flight manual (AFM) to require applying performance penalties for certain takeoff conditions if a thrust reverser is deactivated. That AD also requires revising the Emergency Procedures Section of the FAA-approved AFM to include a flight crew operational procedure for use in the event of any indication of an in-flight thrust reverser deployment. This AD specifies the same requirements for leak checks, but increases the interval between required checks. This AD also removes the requirement to revise the Limitations Section and the Emergency Procedures Section of the applicable AFM when deactivating one or both thrust reversers. This AD results from Airbus Industrie, the airplane manufacturer, revising the master minimum equipment list (MMEL) to include procedures for operating the airplane with the thrust reversers deactivated, and revising the AFM to include procedures for emergency operation if the thrust reversers deploy while in flight. This AD also results from the engine manufacturer recommending extending the interval between inspecting or replacing the DPV. We are issuing this AD to prevent inadvertent thrust reverser deployment, which, if it occurs in-flight, could result in loss of control of the airplane.
Airworthiness Directives; Boeing Model 747-200B, 747-200C, 747-200F, 747-300, and 747SR Series Airplanes Equipped With General Electric (GE) CF6-45 or -50 Series Engines
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 747-200B, 747-200C, 747-200F, 747-300, and 747SR series airplanes, equipped with GE CF6-45 or -50 series engines. This AD requires modifying the side cowl assemblies on the engines by replacing existing wear plates with new extended wear plates and installing new stop fittings. This AD is prompted by reports of a gap at the interface of the lower portion of the side cowl and the aft flange of the thrust reverser. We are issuing this AD to prevent an excessive quantity of air from entering the fire zone that surrounds the engine, which, in the event of an engine fire, could result in an inability to control or extinguish the fire.
Airworthiness Directives; Airbus Model A330, A340-200, and A340-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A330, A340-200, and A340-300 series airplanes. This AD requires repetitive inspections of a certain bracket that attaches the flight deck instrument panel to the airplane structure; replacement of the bracket with a new, improved bracket; and related investigative and corrective actions if necessary. This AD is prompted by reports of cracking of a certain bracket that attaches the flight deck instrument panel to the airplane structure. We are issuing this AD to detect and correct a cracked bracket. Failure of this bracket, combined with failure of the horizontal beam, could result in collapse of the left part of the flight deck instrument panel, and consequent reduced controllability of the airplane.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
