Special Conditions: Cessna Aircraft Company, Model J182T; Diesel Cycle Engine Installation
These special conditions are issued for the Cessna Aircraft Company (Cessna) Model J182T airplane. This airplane will have a novel or unusual design feature(s) associated with the installation of an aircraft diesel engine (ADE). The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Ninth Meeting: RTCA Next Gen Advisory Committee (NAC)
The FAA is issuing this notice to advise the public of the ninth meeting of the RTCA NextGen Advisory Committee (NAC).
Airworthiness Directives; The Boeing Company
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-300, -400, and -500 series airplanes. This proposed AD was prompted by fuel system reviews conducted by the manufacturer. This proposed AD would require, depending on airplane configuration, replacing fuel pump power control relays with new relays having a ground fault interrupter (GFI) feature, installing ground studs and a bonding jumper, doing certain bonding resistance measurements, and changing the GFI relay position. This proposed AD would also require revising the maintenance program to incorporate certain airworthiness limitations. We are proposing this AD to prevent damage to the fuel pumps caused by electrical arcing that could introduce an ignition source in the fuel tank, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747- 200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This proposed AD was prompted by a report of a disbonded doubler and a skin crack in section 41 of the fuselage, and multiple reports of cracked or missing fastener heads. This proposed AD would require repetitive inspections for cracking of the fuselage skin, discrepant fasteners, and for disbonds at the doublers; and related investigative and corrective actions if necessary. For certain airplanes, this proposed AD would also require a terminating repair for repair doublers. We are proposing this AD to prevent rapid decompression and loss of structural integrity of the airplane due to such disbonding and subsequent cracking of the skin panels.
Airworthiness Directives; The Boeing Company Airplanes
We are superseding an existing airworthiness directive (AD) for certain The Boeing Company Model 757-200 and -200PF series airplanes. That AD currently requires modifying the nacelle strut and wing structure, and repairing any damage found during the modification. This new AD specifies a maximum compliance time limit that overrides the optional threshold formula results. This AD was prompted by reports indicating that the actual operational loads applied to the nacelle are higher than the analytical loads that were used during the initial design. Subsequent analysis and service history, which includes numerous reports of fatigue cracking on certain strut and wing structure, indicated that fatigue cracking can occur on the primary strut structure before an airplane reaches its design service objective. We are issuing this AD to prevent fatigue cracking in primary strut structure and consequent reduced structural integrity of the strut.
Airworthiness Directives; Spectrolab Nightsun XP Searchlight
We are adopting a new airworthiness directive (AD) for a certain Spectrolab Nightsun XP Searchlight Assembly (searchlight) installed on, but not limited to Agusta S.p.A. (Agusta) Model AB139 and Model AW139 helicopters, Sikorsky Aircraft Corporation (Sikorsky) Model S-92A helicopters, and Eurocopter Deutschland GmbH (Eurocopter) Model EC135 and Model MBB-BK 117 C-2 helicopters. This AD requires, before further flight, inserting information into the Normal Procedures section of the Rotorcraft Flight Manual (RFM), a daily check of the searchlight, and at a specified time interval or if certain conditions are found, modifying any affected searchlight gimbal assembly. This AD was prompted by a report of a searchlight vibrating and an investigation that revealed that the gimbal azimuth top nut was loose. A loose nut, if not detected and corrected, could result in a gap between the rubber edging of the top shroud and the gimbal frame, leading to degradation of pointing accuracy and stability performance of the searchlight and excessive vibration. If the nut were to entirely disengage, the searchlight could disconnect partially or totally from the helicopter, resulting in damage to the helicopter and injury to persons on the ground. The actions of this AD are intended to ensure that the searchlight remains firmly attached to the helicopter.
Airworthiness Directives; Agusta S.p.A. Helicopters
We are superseding an existing airworthiness directive (AD) for Agusta S.p.A. (Agusta) Model A119 and AW119 MKII helicopters. The existing AD currently requires inspecting the pilot and copilot engine rotary variable differential transformer (RVDT) control box assemblies to determine if the control gear locking pin is in its proper position. Since we issued that AD, Agusta has developed a terminating action for this inspection. This AD requires the same actions as the existing AD as well as modifying the RVDT control box assemblies. The actions of this AD are intended to prevent failure of an RVDT control box assembly, loss of manual control of the engine throttle, and subsequent loss of control of the helicopter.
Airworthiness Directives; Slingsby Sailplanes Ltd. Sailplanes
We are superseding an existing airworthiness directive (AD) for all Slingsby Sailplanes Ltd. Models Dart T.51, Dart T.51/17, and Dart T.51/17R sailplanes equipped with aluminum alloy spar booms. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as an incident of glue joint failure on a starboard wing caused by water entering the area of the airbrake box that resulted in delamination and corrosion in the area of the aluminum alloy spar booms and the wing attach fittings. We are issuing this AD to require actions to address the unsafe condition on these products.