Federal Aviation Administration January 19, 2012 – Federal Register Recent Federal Regulation Documents

Airworthiness Directives; Glasflugel Gliders
Document Number: 2012-928
Type: Proposed Rule
Date: 2012-01-19
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for Glasflugel Models Standard Libelle-201B, Club Libelle 205, Mosquito, and Kestrel gliders. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as corrosion damage to the elevator control rod that could lead to failure of the elevator control rod, possibly resulting in loss of control of the glider. We are issuing this proposed AD to require actions to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2012-859
Type: Proposed Rule
Date: 2012-01-19
Agency: Federal Aviation Administration, Department of Transportation
We propose to supersede an existing airworthiness directive (AD) that applies to certain The Boeing Company Model 737-300, -400, and -500 series airplanes. The existing AD currently requires repetitive inspections for cracking of the crown area of the fuselage skin, and corrective actions if necessary. Since we issued that AD, we received additional reports of cracking at the horizontal chem-mill steps away from the lap joints over the entire crown area, and vertical chem-mill cracks adjacent to the butt joints. This proposed AD would add repetitive inspections for cracking using different inspection methods and would inspect additional areas, and corrective actions if necessary. This proposed AD would also require additional repairs to previously repaired areas and repetitive inspections for loose fasteners and replacement if necessary in certain previously repaired areas. This proposed AD would also reduce certain compliance times and extend certain other compliance times. We are proposing this AD to detect and correct fatigue cracking of the fuselage skin, which could cause the fuselage skin to fracture and fail, and result in rapid decompression of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2012-858
Type: Proposed Rule
Date: 2012-01-19
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for all The Boeing Company Model 717-200 airplanes. This proposed AD was prompted by reports of cracks found on the center section ribs of the horizontal stabilizers. This proposed AD would require repetitive inspections for cracking of the aft face of the left and right rib hinge bearing lugs of the center section of the horizontal stabilizer; and crack measurement, repairs, and installation of a new center section rib if necessary. We are proposing this AD to detect and correct cracks in the left and right bearing lugs of the rib hinge spreading at the same time, which could result in failure of both hinge bearing lugs. Failure of the hinge bearing lugs could result in the inability of the horizontal stabilizer to sustain flight loads and therefore reduce the controllability of the airplane.
Airworthiness Directives; Bombardier, Inc. Airplanes
Document Number: 2012-857
Type: Proposed Rule
Date: 2012-01-19
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702); CL-600-2D15 (Regional Jet Series 705); CL-600-2D24 (Regional Jet Series 900); and CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed AD was prompted by reports of deformation of the pressure regulator on the oxygen cylinder, which was attributed to batches of raw material that did not meet required tensile strength. This proposed AD would require an inspection to determine if certain oxygen pressure regulators are installed, and replacement of oxygen cylinder and regulator assemblies (CRAs) containing pressure regulators that do not meet required material properties. We are proposing this AD to prevent elongation of the pressure regulator neck, which could result in rupture of the oxygen cylinder, and in the case of cabin depressurization, oxygen would not be available when required.
Airworthiness Directives; The Boeing Company Airplanes
Document Number: 2012-856
Type: Proposed Rule
Date: 2012-01-19
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 777 airplanes. This proposed AD was prompted by reports that escape slides/rafts did not deploy due to galvanic corrosion of the door-mounted slide/raft packboard release mechanisms. This proposed AD would require doing a general visual inspection of the housing assembly of the packboard release mechanism to determine if its surface treatment has been sealed, and if unsealed, replacing the housing assembly with a new or serviceable housing assembly. We are proposing this AD to detect and correct corrosion of the packboard release mechanisms, which could interfere with escape slide/raft deployment, prohibit doors from opening in the armed mode, and cause consequent delay and injury during evacuation of passengers and crew from the cabin in the event of an emergency.
Airworthiness Directives; Cessna Aircraft Company Airplanes
Document Number: 2012-855
Type: Proposed Rule
Date: 2012-01-19
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Cessna Aircraft Company Model 560XL airplanes. This proposed AD was prompted by reports of wheel inserts becoming loose and damaging brake assemblies on Model 560XL airplanes. This proposed AD would require an inspection of the torque lug and surrounding components (wheel base, side rim, lock ring) for damage (such as corrosion, cracks, dents, bent areas, damaged or missing paint or primer, or wear on the metal), and of the bearing cup for corrosion, turned cup, or clearance that exceeds limits, and repair as applicable; measuring the torque lugs for width and replacing screws and inserts with new, improved screws and inserts; and re-identifying the wheel assemblies. We are proposing this AD to correct the unsafe condition on these products.
Airworthiness Directives; Bombardier, Inc. Airplanes
Document Number: 2012-854
Type: Proposed Rule
Date: 2012-01-19
Agency: Federal Aviation Administration, Department of Transportation
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This proposed AD was prompted by chafing on high pressure fuel lines due to improper installation of an expandable pin on the lower cowl assembly. This proposed AD would require installing spring clips and repositioning the lanyard attachment points at the forward end and the forward firefloor of the lower cowl. We are proposing this AD to prevent chafing of the high pressure fuel lines, which if not corrected, could cause fuel leakage in a fire zone.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.