Federal Aviation Administration May 25, 2006 – Federal Register Recent Federal Regulation Documents

Voluntary Disclosure Reporting Program
Document Number: E6-8078
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA is proposing that information provided to the agency from a Voluntary Disclosure Reporting Program (VDRP) be designated by an FAA order as protected from public disclosure in accordance with the provisions of 14 CFR part 193. Under 49 U.S.C. 40123, the FAA is required to protect the information from disclosure to the public, including disclosure under the Freedom of Information Act (5 U.S.C. 552) or other laws, following issuance of such order. The designation is intended to encourage participation in the VDRP.
Airworthiness Directives; McDonnell Douglas Model MD-90-30 Airplanes
Document Number: E6-8011
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for all McDonnell Douglas Model MD-90-30 airplanes. This proposed AD would require installing a clamp, bonding jumper assembly, and attaching hardware to the refueling manifold in the right wing refueling station area. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to prevent arcing on the in-tank side of the fueling valve during a lightning strike, which could result in an ignition source that could ignite fuel vapor and cause a fuel tank explosion.
Airworthiness Directives; McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-30, DC-10-30F (KDC-10), DC-10-40, and DC-10-40F Airplanes
Document Number: E6-8010
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain McDonnell Douglas airplanes, identified above. This proposed AD would require reducing the length of the sump drain collar and replacing the fuel tank sump drain lockring for fuel tanks 1, 2, and 3; and reducing the length of the drain outlet barrel for the auxiliary fuel tank, if applicable. For airplanes with an auxiliary fuel tank, this proposed AD also would require relocating the sump drain outlet to allow draining the sumps without opening the doors of the main landing gear wheel well. This proposed AD results from fuel system reviews conducted by the manufacturer. We are proposing this AD to reduce the potential of ignition sources inside fuel tanks in the event of a lightning strike, which, in combination with flammable fuel vapors, could result in arcing in the fuel tank, fuel tank explosions, and consequent loss of the airplane.
Airworthiness Directives; Fokker Model F.28 Mark 0070 and 0100 Airplanes
Document Number: E6-8009
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for all Fokker Model F.28 Mark 0070 and 0100 airplanes. This proposed AD would require modification of the wiring distribution of the alternating current bus transfer power system and the right-hand and left-hand windshield anti-icing system, as necessary. This proposed AD results from a report of electrical sparks coming out of the flight deck from a panel behind the left seat. We are proposing this AD to prevent failure of the sliding window heating element(s), due to electrical overload, which could result in smoke and fire in the cockpit.
Airworthiness Directives; Bombardier Model DHC-8-102, -103, and -106 Airplanes, and DHC-8-200 and DHC-8-300 Series Airplanes
Document Number: E6-8008
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier Model DHC-8-102, -103, and -106 airplanes, and DHC-8-200 and DHC-8-300 series airplanes. This proposed AD would require performing a one-time inspection for non-conforming chain links of chain assemblies of the elevator trim system and gust lock system, and corrective actions if necessary. This proposed AD would also require temporary revisions to the airplane flight manuals of the affected airplanes, which describe procedures for elevator trim checks. This proposed AD results from several reports of failure of the elevator trim chain, due to hydrogen embrittlement. We are proposing this AD to prevent breakage of the elevator trim chain, which would prevent the actual position of the elevator trim tab from being annunciated to the flightcrew. Attempting to adjust the trim tab to the full nose up or full nose down position with a broken trim chain could cause reduced control during airplane rotation on the ground or a stall during flight.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-200B, 747-200C, 747-200F, 747SR, and 747SP Series Airplanes
Document Number: E6-8007
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 747 series airplanes. The existing AD currently requires repetitive inspections to detect cracks at certain stringer fastener locations; and repair, if necessary. For certain airplanes, the existing AD requires a modification in certain areas where reports indicate that cracking was prevalent. This modification terminates the repetitive inspections only for those areas, and is also an option for other airplanes affected by the existing AD. This proposed AD would require one-time inspections at a reduced inspection threshold of areas that may have Alodine-coated rivets installed, and repair if necessary. This proposed AD results from a report of cracking discovered in a skin lap joint that was previously inspected using the eddy current method. We are proposing this AD to prevent rapid decompression of the airplane due to disbonding and subsequent cracking of the skin panels.
Airworthiness Directives; Boeing Model 747 Airplanes
Document Number: E6-8006
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to supersede an existing airworthiness directive (AD) that applies to certain Boeing Model 747 airplanes. The existing AD currently requires inspections to detect disbonding, corrosion, and cracking at the longitudinal rows of fasteners in the bonded skin panels in section 41 of the fuselage, and repair, if necessary. This proposed AD would add airplanes to the applicability, and require new inspections of airplanes that may have Alodine-coated rivets installed. This proposed AD results from a report of cracking discovered in a skin lap joint that was previously inspected using the eddy current method. We are proposing this AD to prevent rapid decompression of the airplane due to disbonding and subsequent cracking of the skin panels.
RTCA Government/Industry Air Traffic Management Advisory Committee
Document Number: 06-4861
Type: Notice
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of a meeting of RTCA Government/Industry Air Traffic Management Advisory Committee.
RTCA Special Committee 186: Automatic Department Surveillance-Broadcast (ADS-B)
Document Number: 06-4860
Type: Notice
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA is issuing this notice to advise the public of a meeting of RTCA Special Committee 186: Automatic Dependent SurveillanceBroadcast (ADS-B).
Airworthiness Directives; Lycoming Engines (L)O-360, (L)IO-360, AEIO-360, O-540, IO-540, AEIO-540, (L)TIO-540, IO-580, AEIO-580, and IO-720 Series Reciprocating Engines
Document Number: 06-4850
Type: Proposed Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA proposes to adopt a new airworthiness directive (AD) for certain Lycoming Engines (L)O-360, (L)IO-360, AEIO-360, O-540, IO- 540, AEIO-540, (L)TIO-540, IO-580, AEIO-580, and IO-720 series reciprocating engines. This proposed AD would require replacing certain crankshafts. This proposed AD results from reports of 23 confirmed failures of similar crankshafts in Lycoming Engines 360 and 540 series reciprocating engines. We are proposing this AD to prevent failure of the crankshaft, which will result in total engine power loss, in-flight engine failure, and possible loss of the aircraft.
Airworthiness Directives; Boeing Model 767-200 and -300 Series Airplanes
Document Number: 06-4803
Type: Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-200 and -300 series airplanes. This AD requires replacing the placards on certain stowage bins with new placards, installing partial dividers in certain other stowage bins, and installing straps on stowage bins containing life rafts. For certain airplanes, this AD also requires related concurrent actions. This AD results from test data indicating that outboard overhead stowage bins are unable to withstand the 4.5g down-load standard intended to protect passengers during flight turbulence or a hard landing. We are issuing this AD to prevent the stowage bins from opening during flight turbulence or a hard landing, which could result in the contents of the stowage bins falling onto the passenger seats below and injuring passengers, or blocking the aisles, impeding the evacuation of passengers in an emergency.
Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes
Document Number: 06-4802
Type: Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA is superseding an existing airworthiness directive (AD), which applies to certain BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ airplanes. That AD currently requires a one- time inspection to detect corrosion of the flap structure and machined ribs, corrective actions if necessary, and reprotection of the rib boss bores. This new AD requires a records review of the results of that inspection, and an additional inspection and related investigative/ corrective action if necessary. This AD results from the development of an improved inspection for corrosion in the subject area. We are issuing this AD to detect and correct corrosion in the flap structure and machined ribs, which could result in reduced structural integrity of the airplane.
Airworthiness Directives; Raytheon Model Hawker 800XP Airplanes
Document Number: 06-4801
Type: Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for certain Raytheon Model Hawker 800XP airplanes. This AD requires inspecting certain bus bars in the DA-A panel to ensure that the bus bars match the panel configuration and clearance is adequate between the bus bars and adjacent components, and performing corrective action if necessary. This AD results from two reports of inadequate clearance between the bus bars in the DA-A panel. We are issuing this AD to prevent insufficient electrical isolation for the electrical bus configuration and inability of the flightcrew to isolate the bus bars in an emergency situation involving a dual generator failure, which could result in extra loads on the main ship batteries and consequent loss of power to the main essential bus.
Airworthiness Directives; Gulfstream Model GV and GV-SP Series Airplanes
Document Number: 06-4714
Type: Rule
Date: 2006-05-25
Agency: Federal Aviation Administration, Department of Transportation
The FAA is adopting a new airworthiness directive (AD) for all Gulfstream Model GV and certain Model GV-SP series airplanes. This AD requires a one-time inspection of the left and right aileron and elevator actuators to determine the part and serial numbers of each actuator, repetitive inspections of suspect actuators to detect broken damper shafts, and replacement of any actuator having a broken damper shaft. This AD also requires that operators report any broken damper shaft they find to the FAA. This AD also requires a terminating action for the repetitive inspections. This AD results from reports of broken or cracked damper shafts within the aileron and elevator actuator assemblies. We are issuing this AD to prevent broken damper shafts, which could result in locking of an aileron or elevator actuator (hard- over condition), which would activate the hard-over protection system (HOPS), resulting in increased pilot workload and consequent reduced controllability of the airplane.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.