Federal Aviation Administration April 19, 2006 – Federal Register Recent Federal Regulation Documents
Results 1 - 5 of 5
Airworthiness Directives; Pratt & Whitney PW4077D, PW4084D, PW4090, and PW4090-3 Turbofan Engines
The FAA proposes to adopt a new airworthiness directive (AD). This proposed AD is for Pratt & Whitney (PW) PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engines that were reassembled with certain previously used high pressure compressor (HPC) exit brush seal assembly parts and certain new or refurbished HPC exit diffuser air seal inner lands. This proposed AD would require replacing the HPC exit inner and outer brush seal packs with new brush seal packs, or replacing the HPC exit brush seal assembly with a new HPC exit brush seal assembly. This proposed AD results from a report of oil leaking into the high pressure turbine (HPT) interstage cavity and igniting, leading to an uncontained failure of the 2nd stage turbine air seal and engine in-flight shutdown. We are proposing this AD to prevent uncontained engine failure, damage to the airplane, and injury to passengers.
Airworthiness Directives; Pilatus Aircraft Ltd. Models PC-12 and PC-12/45 Airplanes
We are adopting a new airworthiness directive (AD) for all Pilatus Aircraft Ltd. Models PC-12 and PC-12/45 airplanes equipped with certain crew seat bucket assemblies with and without a backrest recline system. This AD requires you to replace the backrest tubes on these crew seat bucket assemblies at a specified time and adds a life limit for these backrest tubes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland. We are issuing this AD to prevent cracks in the backrest tubes of certain crew seat bucket assemblies, which could result in failure of the seat system. This failure could lead to the pilot and co-pilot's reduced ability to control the airplane. This failure could also affect the proper function of the seat restrain system in the case of an emergency landing.
Airworthiness Directives; General Electric Company CT64-820-4 Turboprop Engines
The FAA is adopting a new airworthiness directive (AD) for General Electric Company (GE) CT64-820-4 turboprop engines with certain part number (P/N) rotating parts. The parts are in the compressor rotor assembly, gas generator turbine rotor assembly, and power turbine rotor assembly that are subject to low-cycle fatigue. This AD requires removing from service these affected rotating parts at reduced compliance times. This AD results from the manufacturer's discovery of cracks in some rotating parts. We are issuing this AD to prevent cracks in the rotating parts that could cause compressor and turbine wheel fracture and uncontained engine failure. An uncontained engine failure could cause possible damage to the airplane.
Airworthiness Directives; Air Tractor, Inc. Models AT-400; AT-401, AT-401B, AT-402, AT-402A, and AT-402B Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Air Tractor, Inc. (Air Tractor) Models AT-400, AT-401, AT-401B, AT-402, AT-402A, and AT-402B airplanes. This AD requires you to lower the safe life for the wing lower spar cap for certain Models AT-402A and AT-402B airplanes and those that incorporate or have incorporated Marburger Enterprises, Inc. (Marburger) winglets. For Models AT-400, AT-401, AT-401B, AT-402, and certain AT-402A, airplanes, this AD requires you to repetitively inspect the wing lower spar cap in order to reach the safe life. We also developed an alternative method of compliance (AMOC) to the requirements of this Ad for certain Models AT- 402A and AT-402B airplanes. The AMOC includes repetitive eddy current inspections, modification of the center splice connection, and lower spar cap replacement. This AD is the result of reports of cracks in the \3/8\-inch bolt hole of the wing lower spar cap before reaching the approved safe life. We are issuing this AD to prevent fatigue cracks from occurring in the wing lower spar cap before the originally established safe life is reached. Fatigue cracks in the wing lower spar cap, if not detected and corrected, could result in wing separation and loss of control of the airplane.
Airworthiness Directives; Air Tractor, Inc. Models AT-802 and AT-802A Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Air Tractor, Inc. (Air Tractor) Models AT-802 and AT-802A airplanes. This AD requires you to repetitively inspect (using the eddy current method) the two outboard fastener holes in both of the wing main spar lower caps at the center splice joint for cracks and repair or replace any cracked spar cap. This AD results from in-service fatigue cracking of the wing main spar lower cap at the center splice joint outboard fastener hole at hours time-in-service below the safe life limit established for these airplanes in AD 2002-11-05. We are issuing this AD to detect and correct cracks in the wing main spar lower cap at the center splice joint, which could result in failure of the spar cap and lead to wing separation and loss of control of the airplane.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
