Federal Aviation Administration January 8, 2025 – Federal Register Recent Federal Regulation Documents
Results 1 - 7 of 7
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures; Miscellaneous Amendments
This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Airworthiness Directives; Airbus Defense and Space S.A. (Formerly Known as Construcciones Aeronauticas, S.A.) Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Airbus Defense and Space S.A. Model CN-235, CN-235-200, and CN-235-300 airplanes. This AD was prompted by a torn bulkhead seal found jamming the nose landing gear (NLG) emergency cable pulley. Due to the similarity of design, the main landing gear (MLG) emergency cable pulley could be exposed to the same failure mode. This AD requires repetitive inspections and corrective actions for damage of affected bulkhead seals and retainer rings, and repetitive replacement of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 767-200, -300, and -300F airplanes. This AD was prompted by a report of a main landing gear (MLG) collapse event following maintenance where a grinder was operating outside of its input parameters, resulting in possible heat damage to the outer cylinder of the MLG. This AD requires replacing affected outer cylinders. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Gulfstream Aerospace Corporation Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation Model GVII-G500 and GVII-G600 airplanes. This AD was prompted by a report of cracking in the electrical grounding receptacles located on the left and right wings. This AD requires inspecting the electrical grounding receptacles for cracks and corrosion, performing applicable on-condition actions, and sealing over the grounding receptacles on the top of the wings to permanently disable the receptacle. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; General Electric Company Engines
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model GEnx-1B64, GEnx-1B64/P1, GEnx-1B64/P2, GEnx-1B67, GEnx-1B67/P1, GEnx-1B67/P2, GEnx-1B70, GEnx- 1B70/75/P1, GEnx-1B70/75/P2, GEnx-1B70/P1, GEnx-1B70/P2, GEnx-1B70C/P1, GEnx-1B70C/P2, GEnx-1B74/75/P1, GEnx-1B74/75/P2, GEnx-1B76/P2, GEnx- 1B76A/P2, GEnx-2B67, GEnx-2B67B, and GEnx-2B67/P engines. This AD was prompted by a manufacturer evaluation that determined a lower life limit may be necessary for certain stages 6-10 compressor rotor spools than allowed by the engine shop manual (ESM). This AD requires a one- time inspection of the stages 6-10 spools for previously accomplished blend repairs, a one-time inspection of the blend repairs on the stages 6-10 spools for compliance with the updated allowable limits, and replacement if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; CFM International, S.A. Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model LEAP-1B engines. This AD was prompted by a report of a quality escape involving certain high- pressure compressor (HPC) stage 2 seals manufactured without detailed finish machining, which could result in deeper rubs and mechanical damage to the seal teeth of the stage 3-4 compressor rotor blisk (stage 3-4 blisk) of the mating compressor rotor during initial operation. This AD requires a visual inspection of the HPC stage 2 seal, a visual inspection of the forward arm seal teeth of the stage 3-4 blisk, an eddy current inspection (ECI) of the forward arm seal teeth of the stage 3-4 blisk, and replacement of the HPC stage 2 seal and the stage 3-4 blisk, if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
