Federal Aviation Administration December 28, 2023 – Federal Register Recent Federal Regulation Documents
Results 1 - 5 of 5
Airworthiness Directives; International Aero Engines, LLC Engines
The FAA is withdrawing a notice of proposed rulemaking (NPRM) that proposed to supersede Airworthiness Directive (AD) 2022-19-15, which applies to certain International Aero Engines, LLC (IAE LLC) Model PW1100G series engines; and AD 2023-16-07, which applies to certain IAE LLC Model PW1100G series engines and PW1400G series engines. AD 2022-19-15 requires an angled ultrasonic inspection (AUSI) of the high-pressure turbine (HPT) 1st-stage disk and HPT 2nd-stage disk, and replacement if necessary. AD 2023-16-07 requires an AUSI of the HPT 1st-stage hub (also known as the HPT 1st-stage disk) and HPT 2nd-stage hub (also known as the HPT 2nd-stage disk) for cracks, and replacement if necessary, which is terminating action for AD 2022-19- 15. The NPRM was prompted by a manufacturer investigation that determined an increased risk of powder metal anomalies for all powder metal parts in certain powder metal production campaigns, which are susceptible to failure significantly earlier than previously determined. The NPRM would have retained the AUSI requirement for certain HPT 1st-stage and HPT 2nd-stage hubs from AD 2023-16-07. The NPRM would also have required performing an AUSI of the HPT 1st-stage hub, HPT 2nd-stage hub, high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7), and HPC 8th-stage integrally bladed rotor (IBR-8) for cracks and replacement if necessary. The NPRM would also have required accelerated replacement of the HPC IBR-7, HPC IBR-8, HPC rear hub, HPT 1st-stage hub, HPT 1st-stage air seal, HPT 1st-stage blade retaining plate, HPT 2nd-stage hub, HPT 2nd-stage blade retaining plate, and HPT 2nd-stage rear seal. Since issuance of the NPRM, the FAA has received information that an error was inadvertently included in the compliance times for some of the HPT 1st-stage and 2nd-stage hubs, which would have required removal significantly later than necessary. Accordingly, the NPRM is withdrawn.
Airworthiness Directives; Airbus Helicopters
The FAA is superseding Airworthiness Directive (AD) 2022-27- 09, which applied to certain Airbus Helicopters Model EC130T2 helicopters. AD 2022-27-09 required repetitively inspecting the vibration level on the tail rotor drive shaft and, depending on the results, taking corrective action. AD 2022-27-09 also required reporting information and prohibited installing certain rotor drive shafts unless the inspection was done. Since the FAA issued AD 2022-27- 09, Airbus Helicopters revised its service information to update the procedures for inspecting that vibration level, reduce an allowable vibration level, and clarify when a balance correction may be accomplished. This AD was prompted by the determination that a certain vibration measurement tool was providing unexpected results and therefore the threshold must be revised. This AD continues to require certain actions in AD 2022-27-09 and also revises the procedures for inspecting the vibration level on the tail rotor drive shaft and depending on these results, requires replacing certain parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; International Aero Engines, LLC Engines
The FAA proposes to supersede Airworthiness Directive (AD) 2022-19-15, which applies to certain International Aero Engines, LLC (IAE LLC) Model PW1100G series engines; and AD 2023-16-07, which applies to certain IAE LLC Model PW1100G series engines and PW1400G series engines. AD 2022-19-15 requires an angled ultrasonic inspection (AUSI) of the high-pressure turbine (HPT) 1st-stage disk and HPT 2nd- stage disk, and replacement if necessary. AD 2023-16-07 requires an AUSI of the HPT 1st-stage hub (also known as the HPT 1st-stage disk) and HPT 2nd-stage hub (also known as the HPT 2nd-stage disk) for cracks, and replacement if necessary, which is terminating action for AD 2022-19-15. Since the FAA issued those two ADs, an investigation determined an increased risk of powder metal anomalies for all powder metal parts in certain powder metal production campaigns, which are susceptible to failure significantly earlier than previously determined. This proposed AD would retain the AUSI requirement for certain HPT 1st-stage and HPT 2nd-stage hubs from AD 2023-16-07. This proposed AD would also require performing an AUSI of the HPT 1st-stage hub, HPT 2nd-stage hub, high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7), and HPC 8th-stage integrally bladed rotor (IBR-8) for cracks and replacement if necessary. This proposed AD would also require accelerated replacement of the HPC IBR-7, HPC IBR-8, HPC rear hub, HPT 1st-stage hub, HPT 1st-stage air seal, HPT 1st-stage blade retaining plate, HPT 2nd-stage hub, HPT 2nd-stage blade retaining plate, and HPT 2nd-stage rear seal. The FAA is proposing this AD to address the unsafe condition on these products.
Revisions to Civil Penalty Amounts, 2024
This final rule provides the statutorily prescribed 2024 adjustment to civil penalty amounts that may be imposed for violations of certain DOT regulations.
Airworthiness Directives; Bombardier, Inc., Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes. This proposed AD was prompted by a report indicating that a new filter plate connector for the nose wheel steering (NWS) system electronic control module (ECM) does not meet certain certification requirements. This proposed AD would require replacing all affected non-compliant ECMs. This proposed AD would also prohibit the installation of affected parts under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
