Federal Aviation Administration June 7, 2016 – Federal Register Recent Federal Regulation Documents
Results 1 - 9 of 9
Recommendations for Facilities Realignments To Support Transition to NextGen as Part of Section 804 of the FAA Modernization and Reform Act of 2012-Part 2; Request for Comments
This document announces the availability of the FAA National Facilities Realignment and Consolidation Report, Part 2. The report was developed in response to Section 804 of the FAA Modernization and Reform Act of 2012 (Pub. L. 112-95). The report and recommendations contained therein have been developed collaboratively with the National Air Traffic Controllers Association (NATCA) and the Professional Aviation Safety Specialists (PASS) labor unions and with input from stakeholders. The FAA seeks comments on this report.
Airworthiness Directives; Fokker Services B.V. Airplanes
We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by the need for more restrictive airworthiness limitations. This AD requires revising the maintenance or inspection program, as applicable, to incorporate certain maintenance requirement tasks, thresholds, and intervals. We are issuing this AD to reduce the potential for significant failure conditions and consequent loss of controllability of the airplane.
Airworthiness Directives; Fokker Services B.V. Airplanes
We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F28 Mark 0070 and 0100 airplanes. This AD was prompted by the need for more restrictive fuel system airworthiness limitations. This AD requires revising the maintenance program or inspection program, as applicable, to incorporate certain fuel system airworthiness limitations. We are issuing this AD to reduce the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 787 airplanes. This AD was prompted by the disclosure that the inner diameters of some batches of landing gear pins were not shot peened in accordance with design specifications, and need to be replaced. This AD requires inspection for improperly manufactured landing gear pins, and replacement if necessary. We are issuing this AD to detect and correct insufficient shot peening that could lead to stress corrosion cracking and failure of the landing gear pin, and cause landing gear collapse and inability to control the airplane at high speeds on the ground.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 airplanes. This AD was prompted by a report of wire chafing caused by a left wing spoiler actuator wire not having enough separation from a certain bracket when the spoiler is in the deployed position. This AD requires measuring the separation between a certain electro-mechanical actuator wire of the left wing, spoiler 4, and the support bracket of the flap variable camber trim unit; and related investigative and corrective actions if necessary. We are issuing this AD to detect and correct wire chafing. Such chafing could result in an electrical short and potential fire in a flammable fluid leakage zone and possible loss of several functions essential for safe flight.
Airworthiness Directives; EVEKTOR, spol. S.r.o. Gliders
We are adopting a new airworthiness directive (AD) for EVEKTOR, spol. s.r.o. Models L 13 SEH VIVAT and L 13 SDM VIVAT gliders (type certificate previously held by AEROTECHNIK s.r.o.). This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as lack of distinct color marking of the elevator drive. We are issuing this AD to require actions to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300 series airplanes equipped with Pratt and Whitney engines. This AD was prompted by reports of blocked drain lines at the engine forward strut that caused flammable fluid to accumulate in a flammable leakage zone. This AD requires doing the following actions on the left strut and right strut: A one-time cleaning of certain forward strut drain lines; installing new forward strut drain lines and insulation blankets; a leak check of the forward strut drain lines; and repair if any leak is found. This AD also requires revising the maintenance or inspection program, as applicable, to incorporate a certain airworthiness limitation. We are issuing this AD to prevent blockage of forward strut drain lines. This condition could cause flammable fluids to collect in the forward strut area and potentially cause an uncontrolled fire or cause failure of engine attachment structure and consequent airplane loss.
Airworthiness Directives; Airbus Airplanes
We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-200 and -300 series airplanes, Model A330-200 Freighter series airplanes, and Model A340-541 and A340-642 airplanes. This AD was prompted by a report of an under-torqued forward engine mount bolt. This AD requires a one-time torque check of the forward and aft engine mount bolts and corrective actions if necessary. We are issuing this AD to detect and correct improperly torqued engine mount bolts, which could lead to detachment of the engine from the airplane during flight and consequent damage to the airplane and injury to persons on the ground.
Airworthiness Directives; Fokker Services B.V. Airplanes
We are adopting a new airworthiness directive (AD) for certain Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by a design review that revealed that a wiring failure, external to the center wing fuel tank, could cause a hot short circuit to a maximum level sensor wire, and result in excessive heating of the maximum level sensor element. This AD requires modifying the wiring of the maximum level sensors in the center wing fuel tank, performing after-installation tests, and corrective action if necessary. This AD also requires revising the airplane maintenance or inspection program to incorporate fuel airworthiness limitation items and critical design configuration control limitations. We are issuing this AD to prevent the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
