Federal Aviation Administration August 5, 2008 – Federal Register Recent Federal Regulation Documents
Results 1 - 7 of 7
Agency Information Collection Activity Seeking OMB Approval
The FAA invites public comments about our intention to request the Office of Management and Budget's (OMB) revision of a current information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on May 15, 2008, vol. 73, no. 95, page 28184. The information collected is used by the FAA to register aircraft or hold an aircraft in trust.
Agency Information Collection Activity Seeking OMB Approval
The FAA invites public comments about our intention to request the Office of Management and Budget's (OMB) revision of a current information collection. The Federal Register Notice with a 60-day comment period soliciting comments on the following collection of information was published on May 14, 2008, vol. 73, no. 94, page 27885. Collection of this information permits the FAA to evaluate its certification standards, maintenance programs, and regulatory requirements since their effectiveness is reflected in the number of equipment failures or the lack thereof.
Airworthiness Directives; Boeing Model 777-200 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 777-200 series airplanes. This AD requires repetitive inspections for any wrinkle in certain external skin panels, and for cracking at the fuselage bulkhead shear tie end fastener locations at certain stations of Section 48 of the fuselage; and doing related investigative and corrective actions if necessary. This AD results from a report of cracks found in the external skin on the left and right sides of the Section 48 panel of the fuselage on two airplanes with skin wrinkles found at two of the external crack locations. We are issuing this AD to detect and correct wrinkles and cracks in certain external skin panels of Section 48, which could join together and result in reduced structural integrity of support structure for the vertical and horizontal stabilizers and inability of the airplane to sustain limit loads.
Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD requires replacing the pushrods for the left and right elevator tab control mechanisms with new, improved pushrods. This AD results from a report of a rod end fracture on a rudder power control unit (PCU) control rod, which is similar to the ones used for the elevator tab pushrods. Analysis revealed that the fractured rod end had an incorrect hardness, which had probably occurred during the manufacture of the control rod. We are issuing this AD to prevent fracture of the elevator tab pushrod ends, which could result in excessive in-flight vibrations of the elevator tab, possible loss of the elevator tab, and consequent loss of controllability of the airplane.
Airworthiness Directives; Dassault Model Falcon 2000EX Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; BAE Systems (Operations) Limited (Jetstream) Model 4101 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model DHC-8-400, -401 and -402 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
