Federal Aviation Administration August 28, 2007 – Federal Register Recent Federal Regulation Documents

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-300, -400, and -500 series airplanes. This AD requires an inspection of the seat locks and seat tracks of the flightcrew seats to ensure that the seats lock in position and to verify that lock nuts and bolts of adequate length are installed on the rear tracklock bracket, and corrective actions if necessary. This AD results from a report indicating that the captain's seat slid aft and jammed during taxi. We are issuing this AD to prevent uncommanded movement of the flightcrew seats during acceleration and take-off of the airplane, which could result in reduced controllability of the airplane.

The FAA is adopting a new airworthiness directive (AD) for certain Learjet Model 31, 31A, 35, 35A (C-21A), 36, 36A, 55, 55B, and 55C airplanes, and Model 45 airplanes. This AD requires inspecting for unsealed gaps on the pylon side of the engine firewall and cleaning/ sealing any unsealed gap; and, for certain airplanes, inspecting for unsealed gaps of the pylon trailing edge and cleaning/sealing any gap. This AD results from a report that unsealed gaps (penetration points) of the engine firewall were discovered during production. We are issuing this AD to prevent penetration of flammable liquids or fire through the engine firewall into the engine pylon, which could lead to fire inside the airplane.

This amendment adopts a new airworthiness directive (AD), applicable to certain McDonnell Douglas Model DC-9-10, -20, -30, -40, and -50 series airplanes; Model DC-9-81 (MD-81), -82 (MD-82), -83 (MD- 83), and -87 (MD-87) airplanes; and Model MD-88 airplanes; that requires repetitive inspections and functional tests of the static port heater assemblies, and corrective actions if necessary. The actions specified by this AD are intended to prevent an electrical short of the static port heater from sparking and igniting the insulation blanket adjacent to the static port heater, which could result in smoke and/or fire in the cabin area. This action is intended to address the identified unsafe condition.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

The FAA is revising an existing airworthiness directive (AD) for General Electric Company (GE) CF34-1A, -3A, -3A1, -3A2, -3B, and - 3B1 turbofan engines. That AD currently requires a one-time inspection of certain fan disks for electrical arc-out indications, replacing fan disks with electrical arc-out indications, and reducing the life limit of certain fan disks. This AD results from a comment received on AD 2007-07-07, and from recently issued revisions to the applicable GE Alert Service Bulletins (ASBs). We are issuing this AD to prevent an uncontained fan disk failure and airplane damage.

The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model 717-200 airplanes. This AD requires installing in-line fuel float switch fuses and wire protection at the left, right, and center forward spars. This AD results from a design review of the fuel tank systems conducted by the manufacturer. We are issuing this AD to prevent the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs, or maintenance actions, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.

The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 777 series airplanes. This AD requires, for the drive mechanism of the horizontal stabilizer, repetitive detailed inspections for discrepancies; repetitive lubrication of the ballnut and ballscrew; repetitive measurements of the freeplay between the ballnut and the ballscrew; and corrective action if necessary. This AD results from a report of extensive corrosion of a ballscrew in the drive mechanism of the horizontal stabilizer on a Boeing Model 757 airplane, which is similar in design to the ballscrew on Model 777 airplanes. We are issuing this AD to prevent an undetected failure of the primary load path for the ballscrew in the drive mechanism of the horizontal stabilizer and subsequent wear and failure of the secondary load path, which could lead to loss of control of the horizontal stabilizer and consequent loss of control of the airplane.

This notice announces the availability of and requests comments on a proposed revision to Advisory Circular (AC) No. 120-53, Crew Qualification and Pilot Type Rating Requirements for Transport Category Aircraft Operated under 14 CFR part 121. That AC provides the Federal Aviation Administration (FAA) guidance for the evaluation and approval of flight crew qualification programs and the issuance of pilot type ratings for flight crews operating under 14 CFR part 121. The proposed AC streamlines the process described in AC 120-53 for determining the level of differences between aircraft and the credits the FAA assigns between those aircraft for the purposes of training, checking, and recency of experience requirements. The applicability of the proposed AC would be limited to operations conducted under 14 CFR part 121.