Federal Aviation Administration December 4, 2006 – Federal Register Recent Federal Regulation Documents
Results 1 - 7 of 7
Airworthiness Directives; Raytheon Aircraft Company Models 1900, 1900C, and 1900D Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Raytheon Aircraft Company (RAC) Models 1900, 1900C, and 1900D airplanes. This AD requires you to repetitively inspect the forward, vertical, and aft flanges of both the left and right wing rear spar lower caps for cracks, repair any cracks found, and report the inspection results to RAC. This AD results from additional fatigue cracks found in this area since inspections were performed to comply with Emergency AD 2006-18-51, which required immediate visual inspections of this area. We are issuing this AD for the purpose of performing a more rigorous inspection requiring cleaning and paint stripping of this section of the wing rear spar to detect and correct cracking in the wing spar lower caps of the affected airplanes before the cracks lead to failure. These wing rear spar cracks may result in wing failure which could result in the wing separating from the airplane with consequent loss of control.
Airworthiness Directives; PZL-Bielsko Model SZD-50-3 “Puchacz” Gliders
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a discrepancy between the design documentation and the Technical Service Manual. In 1981, a castellated nut with cotter pin was introduced to secure the rudder, replacing the self-locking nut through PZL-Bielsko Bulletin No. BE-06/50-3/81. This change has not been introduced to the Technical Service Manual and use of a self-locking nut, in accordance with the Manual, is still possible. We are issuing this AD to require actions that are intended to address the unsafe condition described in the MCAI.
Airworthiness Directives; Air Tractor, Inc. Models AT-501, AT-502, AT-502A, AT-502B, and AT-503A Airplanes
We are adopting a new airworthiness directive (AD) for certain Air Tractor, Inc. Models AT-501, AT-502, AT-502A, AT-502B, and AT-503A airplanes, which supersedes AD 2002- 26-05 and AD 2002-11-05 R1. Since we issued AD 2002-26-05 and AD 2002- 11-05 R1, we determined that additional airplanes should be added to the applicability section and determined the safe life for new production airplanes and replacement spar caps should be extended. We also developed an alternative method of compliance (AMOC) to the requirements of this AD. This AD retains the actions required in AD 2002-26-05 and AD 2002-11-05 R1, adds additional airplanes to the Applicability section, extends the safe life for new production airplanes and replacement spar caps, and incorporates an AMOC. We are issuing this AD to prevent fatigue cracks from occurring in the wing lower spar cap before the established safe life is reached. Fatigue cracks in the wing lower spar cap could result in failure of the spar cap and lead to wing separation.
Airworthiness Directives; International Aero Engines AG (IAE) V2522-A5, V2524-A5, V2527-A5, V2527E-A5, V2527M-A5, V2530-A5, and V2533-A5 Turbofan Engines
The FAA is superseding an existing airworthiness directive (AD) for certain IAE V2522-A5, V2524-A5, V2527-A5, V2527E-A5, V2527M- A5, V2530-A5, and V2533-A5 turbofan engines. That AD currently requires initial and repetitive inspections of the master magnetic chip detector (MCD) or the No. 1, 2, 3 bearing chamber MCD. This AD requires the same MCD inspections. This AD also requires removing certain No. 3 bearings and removing certain high pressure compressure (HPC) stubshaft assemblies as mandatory terminating actions to the repetitive MCD inspections. This AD results from IAE developing a terminating action to the repetitive inspections of the chip detectors, and from expanding the applicability to include additional serial-numbered engines with certain No. 3 bearings installed. We are issuing this AD to prevent failure of the No. 3 bearing, which could result in an in-flight shutdown (IFSD) and smoke in the cockpit and cabin.
Airworthiness Directives; Pratt & Whitney Canada (P&WC) PW535A Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as fuel manifold leakage that could result in engine fire, in-flight shutdown or damage to the airframe. This AD requires actions that are intended to address the unsafe condition described in the MCAI.
Revision of Class E Airspace; Iliamna, AK
This action corrects an error in the airspace description contained in a Final Rule that was published in the Federal Register on Friday, October 6, 2006 (71 FR 59007). Airspace Docket No. 06-AAL-21.
Establishment of Class E Airspace; Kokhanok, AK
This action corrects an error in the location name (Kokhanok) contained in a Final Rule that was published in the Federal Register on Tuesday, October 10, 2006 (71 FR 59372). Airspace Docket No. 06-AAL-19.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
