Department of Transportation October 1, 2018 – Federal Register Recent Federal Regulation Documents
Results 1 - 8 of 8
Senior Executive Service Performance Review Board (PRB) and Executive Resources Board (ERB) Membership
This Federal Register notice serves to inform the public of the current membership of the PRB and ERB, which is as follows:
Airworthiness Directives; CFM International S.A. Turbofan Engines
The FAA is superseding Airworthiness Directive (AD) 2018-10-11 for all CFM International S.A. (CFM) Model CFM56-7B engines. AD 2018- 10-11 required initial and repetitive inspections of certain fan blades and, if they fail the inspection, their replacement with parts eligible for installation. This superseding AD requires the same initial and repetitive inspections but revises the compliance time for the repetitive inspections. This AD was prompted by further analysis by the manufacturer that indicated a need to reduce the repetitive fan blade inspection interval based on ongoing root cause investigation of an April 2018 engine failure. The agency is issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
We are superseding Airworthiness Directive (AD) 2016-25-03, which applied to certain Airbus Model A300 F4-600R series airplanes. AD 2016-25-03 required repetitive high frequency eddy current (HFEC) inspections of the aft lower deck cargo door (LDCD) frame forks; a one- time check of the LDCD clearances; and a one-time detailed visual inspection of hooks, eccentric bushes, and x-stops; and corrective actions if necessary. This AD requires repetitive HFEC inspections of the aft LDCD frame forks; a one-time check of the LDCD clearances; and a one-time detailed visual inspection of hooks, eccentric bushes, and x-stops; and corrective actions if necessary. This AD was prompted by a report of two adjacent frame forks that were found cracked on the aft LDCD of two airplanes during scheduled maintenance, and the introduction of frame fork reinforcement or repair procedures that, when done, allow an extension of repetitive inspection intervals. We are issuing this AD to address the unsafe condition on these products.
Airworthiness Directives; Dassault Aviation Airplanes
We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model MYSTERE-FALCON 200 airplanes. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable, to incorporate new or more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to address the unsafe condition on these products.
Amendment of Class E Airspace; Burlington, WI
This action modifies Class E airspace extending upward from 700 feet above the surface at Burlington Municipal Airport, Burlington, WI. This action is necessary due to the decommissioning of the Burbun VHF omnidirectional range (VOR), cancellation of the VOR approach procedure, and implementation of new area navigation (RNAV) procedures for the safety and management of instrument flight rules (IFR) operations at the airport. This action adjusts the geographic coordinates of the Burlington Municipal Airport to coincide with the FAA's aeronautical database.
Airworthiness Directives; Bombardier, Inc., Airplanes
We propose to supersede Airworthiness Directive (AD) 2008-24- 14, which applies to all Bombardier, Inc., Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. AD 2008-24-14 requires revising the instructions for continued airworthiness to incorporate certain airworthiness limitations for the main landing gear (MLG) trunnion fitting assembly. Since we issued AD 2008-24-14, new airworthiness limitation (AWL) tasks have been introduced with revised inspection, modification, and safe-life requirements. This proposed AD would require revising the maintenance or inspection program, as applicable, to incorporate certain AWLs. It would also require reworking the trunnion fitting in order to meet new structural safe-life limits. We are proposing this AD to address the unsafe condition on these products.
Airworthiness Directives; Airbus SAS Airplanes
We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200 Freighter, -200, and -300 series airplanes; and Airbus SAS Model A340-200, -300, -500, and -600 series airplanes. This AD was prompted by a report of deficient fatigue performance of high strength steel used in forgings. Components made from the affected high strength steel are installed on the main landing gear (MLG), nose landing gear (NLG), and center landing gear (CLG). This AD requires identifying the part number and serial number of certain components installed on the MLG, NLG, and CLG; replacing affected parts; identifying the airplane's weight variant; and determining the applicable life limit for certain components installed on the MLG, NLG, and CLG. We are issuing this AD to address the unsafe condition on these products.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
