Department of Transportation September 18, 2012 – Federal Register Recent Federal Regulation Documents
Results 1 - 11 of 11
Airworthiness Directives; Airbus Airplanes
We are superseding an existing airworthiness directive (AD) for all Airbus Model A330-243, -341, -342 and -343 airplanes. That AD currently requires modifying certain cowl assemblies of the left- and right-hand thrust reversers. This new AD requires removing certain C- duct assemblies of the left- and right-hand thrust reversers from service at certain designated life limits, and also adds airplanes to the applicability. This AD was prompted by new life limits on certain thrust reverser C-duct assemblies. We are issuing this AD to prevent fatigue cracking of the hinges integrated into the 12 o'clock beam of the thrust reversers, which could result in separation of a thrust reverser from the airplane, and consequent reduced controllability of the airplane.
Airworthiness Directives; Piper Aircraft, Inc. Airplanes
We propose to supersede an existing airworthiness directive (AD) that applies to all Piper Aircraft, Inc. Models PA-31, PA-31-325, and PA-31-350 airplanes. The existing AD currently requires a detailed repetitive inspection of the exhaust system downstream of the turbochargers and repair or replacement of parts as necessary. Since we issued that AD, forced landings of aircraft have occurred due to exhaust system failures upstream of aircraft turbochargers and between recurring detailed inspections. This proposed AD would require both visual and detailed repetitive inspections, expanding the inspection scope to include the entirety of each airplane exhaust system. We are proposing this AD to prevent the possibility of an inflight powerplant fire due to an exhaust system failure.
Airworthiness Directives; Stemme GmbH & Co. KG Powered Sailplanes
We propose to adopt a new airworthiness directive (AD) for all Stemme GmbH & Co. KG Models S10, S10-V, and S10-VT powered sailplanes. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as unapproved rubber hoses installed in the engine fuel, oil, and cooling systems, which could lead to a system leak and result in an engine fire. We are issuing this proposed AD to require actions to address the unsafe condition on these products.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-700 and -700C series airplanes. This proposed AD was prompted by reports of early fatigue cracks at chem-mill areas on the crown skin panels. This proposed AD would require repetitive inspections for cracking of the fuselage skin at certain locations at chem-mill areas, and repair if necessary. We are proposing this AD to detect and correct fatigue cracking of the skin panel at the specified chem-mill step locations, which could result in rapid decompression of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-800 series airplanes. This proposed AD was prompted by reports of early fatigue cracks at chem- mill areas on the crown skin panels. This proposed AD would require repetitive inspections for cracking of the fuselage skin along chem- mill steps at certain crown skin and shear wrinkle areas, and repair if necessary. We are proposing this AD to detect and correct fatigue cracking of the skin panel at the specified chem-mill step locations, which could result in rapid decompression of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-600 series airplanes. This proposed AD was prompted by reports of early fatigue cracks at chem- mill areas on the crown skin panels. This proposed AD would require repetitive inspections for cracking of the fuselage skin at certain locations at chem-mill areas, and repair if necessary. We are proposing this AD to detect and correct fatigue cracking of the skin panel at the specified chem- mill step locations, which could result in rapid decompression of the airplane.
Airworthiness Directives; The Boeing Company Airplanes
We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-900 and -900ER series airplanes. This proposed AD was prompted by reports of early fatigue cracks at chem-mill areas on the crown skin panels. This proposed AD would require repetitive inspections for cracking of the fuselage skin along chem-mill steps at certain crown skin and shear wrinkle areas, and repair if necessary. We are proposing this AD to detect and correct fatigue cracking of the skin panel at the specified chem-mill step locations, which could result in rapid decompression of the airplane.
Special Conditions: Embraer S.A., Models EMB-135 and EMB-145 Series; Airplane Seats with Non-Traditional, Large, Non-Metallic Panels
These special conditions are issued for the Embraer S.A. Models EMB-135 and EMB-145 series airplanes. These airplanes will have a novel or unusual design feature associated with the airplane seats that have non-traditional, large, non-metallic panels that would affect survivability during a post-crash fire event. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Tentative Decision That Certain Canadian-Certified
This notice requests comments on a tentative decision by the National Highway Traffic Safety Administration (NHTSA) that certain vehicles that do not comply with all applicable Federal motor vehicle safety standards (FMVSS), but that are certified by their original manufacturer as complying with all applicable Canadian motor vehicle safety standards (CMVSS), are nevertheless eligible for importation into the United States. The vehicles in question either are substantially similar to vehicles that were certified by their manufacturers as complying with the U.S. safety standards and are capable of being readily altered to conform to those standards, or have safety features that comply with, or are capable of being altered to comply with, all U.S. safety standards.
Stage 3 Helicopter Noise Certification Standards
This rulemaking proposes to adopt more stringent noise certification standards for helicopters that are certificated in the United States (U.S.). This rule would apply to applications for a new helicopter type design and for a supplemental type certificate for those new type designs. A helicopter type certificated under this standard would be designated as a Stage 3 helicopter. This rule proposes to adopt the same noise certification standards for helicopters that exist in the standards of the International Civil Aviation Organization (ICAO). The proposal of these more stringent noise certification standards into U.S. regulations is consistent with the FAA's goal of harmonizing U.S. regulations with international standards.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
