Airworthiness Directives; The Boeing Company Airplanes, 57536-57538 [2012-22891]

Download as PDF 57536 Federal Register / Vol. 77, No. 181 / Tuesday, September 18, 2012 / Proposed Rules this AD at whichever of the following occurs later: (i) The v-band coupling reaches a total of 1,000 hours time-in-service (TIS); or (ii) 50 hours TIS after the effective date of this AD, or 6 months after the effective date of this AD, whichever occurs earlier. (2) After the initial replacement required in paragraph (j)(1) of this AD, repetitively thereafter replace the v-band coupling every 1,000 hours TIS. (k) Flange and V-Band Coupling (1) Install serviceable and replacement vband couplings following the applicable instructions contained in Piper Aircraft Corporation Service Bulletin No. 644E, dated May 9, 2012 and/or Lycoming Service Instruction No. 1238B, dated January 6, 2010. (2) Use the applicable torque values specified within Piper Aircraft Corporation Service Bulletin No. 644E, dated May 9, 2012, for Piper v-band couplings; and within Lycoming Service Instruction No. 1238B, dated January 6, 2010, for Lycoming v-band couplings; making sure the torque indicator wrench socket is properly aligned to prevent side loads upon the (v-band coupling) bolt. (3) Align each flange couple so that mating flange surfaces are flat against each other (do not use a v-band coupling to pull flanges into alignment). (4) Verify that the locknuts exhibit a prevailing torque, and replace any locknuts and/or mating couplings with airworthy parts when locknuts are not exhibiting a prevailing torque. Note 1 to paragraph (k) of this AD: During installation, we recommend not opening the v-band coupling more than the MINIMUM diameter necessary to clear coupled flanges. mstockstill on DSK4VPTVN1PROD with PROPOSALS (l) Alternative Methods of Compliance (AMOCs) (1) The Manager, Atlanta Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (m) Related Information (1) For more information about this AD, contact Gary Wechsler, Aerospace Engineer, Atlanta ACO, FAA, 1701 Columbia Avenue, College Park, Georgia 30337; telephone: (404) 474–5575; fax: (404) 474–5606; email: gary.wechsler@faa.gov. (2) For service information identified in this AD, contact Piper Aircraft, Inc., 2926 Piper Drive, Vero Beach, Florida 32960; telephone: (772) 567–4361; fax: (772) 978– 6573; Internet: www.piper.com/home/pages/ Publications.cfm. You may review copies of the referenced service information at the FAA, Small Airplane Directorate, 901 Locust, VerDate Mar<15>2010 16:53 Sep 17, 2012 Jkt 226001 Kansas City, Missouri 64106. For information on the availability of this material at the FAA, call (816) 329–4148. Issued in Kansas City, Missouri, on September 11, 2012. Earl Lawrence, Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 2012–22953 Filed 9–17–12; 8:45 am] BILLING CODE 4910–13–P MC 2H–65, Seattle, WA 98124–2207; telephone 206–544–5000, extension 1; fax 206–766–5680; Internet https:// www.myboeingfleet.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate; 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221. Examining the AD Docket DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2012–0936; Directorate Identifier 2011–NM–269–AD] RIN 2120–AA64 Airworthiness Directives; The Boeing Company Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737–700 and –700C series airplanes. This proposed AD was prompted by reports of early fatigue cracks at chem-mill areas on the crown skin panels. This proposed AD would require repetitive inspections for cracking of the fuselage skin at certain locations at chem-mill areas, and repair if necessary. We are proposing this AD to detect and correct fatigue cracking of the skin panel at the specified chem-mill step locations, which could result in rapid decompression of the airplane. DATES: We must receive comments on this proposed AD by November 2, 2012. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, SUMMARY: PO 00000 Frm 00013 Fmt 4702 Sfmt 4702 You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800–647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Wayne Lockett, Aerospace Engineer, Airframe Branch, ANM–120S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, Washington 98057–3356; phone: (425) 917–6447; fax: (425) 917–6590; email: Wayne.Lockett@faa.gov. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA– 2012–0936; Directorate Identifier 2011– NM–269–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion We received reports of early fatigue cracks near chem-mill areas on the crown skin panels of Model 737–300, –400, and –500 series airplanes. The cracks resulted from high stresses in the areas where chem-mill pockets are adjacent to non-chem-mill areas. E:\FR\FM\18SEP1.SGM 18SEP1 Federal Register / Vol. 77, No. 181 / Tuesday, September 18, 2012 / Proposed Rules Although we have not received any reports of this type of fuselage fatigue cracks on Model 737–600, –700, –700C, –800, –900, or –900ER series airplanes, a full-scale fatigue test article was inspected for skin cracks at similar structural details and two chem-mill cracks were found that occurred late in the testing program. This condition, if not detected and corrected, could result in rapid decompression of the airplane. Relevant Service Information We reviewed Boeing Service Bulletin 737–53–1310, dated October 20, 2011, for Model 737–700 and –700C series airplanes. That service bulletin describes, among other things, procedures for doing repetitive external detailed inspections and external nondestructive inspections (medium frequency eddy current (MFEC), magneto optic imager (MOI), C-scan, or ultrasonic phased array (UTPA) inspections) of the fuselage skin at specified locations where chem-mill areas are adjacent to non-chem-mill areas at antenna and door bearstrap installations, and repairs if necessary. Boeing Service Bulletin 737–53–1310, dated October 20, 2011, also describes procedures for installing modification doublers, which involves an external detailed inspection and an external nondestructive (MFEC, MOI, C-scan, or UTPA) inspection for any cracking of the area to be modified prior to the doubler being placed on that area, a high frequency eddy current inspection of all existing holes for cracking, and contacting Boeing if necessary. That service bulletin also specifies that when a modification is accomplished, the repetitive inspection for the area under the modification is no longer necessary. Boeing Service Bulletin 737–53–1310, dated October 20, 2011, specifies an initial compliance time of 43,000 total flight cycles, or 1,500 flight cycles after the original issue date of that service bulletin, whichever occurs later. That service bulletin specifies a repetitive interval not to exceed 1,500 flight cycles or 2,100 flight cycles, depending on inspection method. For airplanes that have incorporated Boeing Business Jet (BBJ) lower cabin altitude supplemental type certificate (STC) ST010697SE, all initial compliance times specified in flight cycles must be reduced to half of those specified in that service bulletin, and all repeat interval compliance times specified in flight cycles must be reduced to one-quarter of those specified in that service bulletin.+ FAA’s Determination We are proposing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design. Proposed AD Requirements This proposed AD would require accomplishing the actions specified in the service information described previously, except as discussed under ‘‘Differences Between the Proposed AD and the Service Information.’’ Similar Rulemaking The crown skin panels on Model 737– 700 and –700C series airplanes are of a similar design to those on Model 737– 300, –400, –500, –600, –800, –900, and 57537 –900ER series airplanes. Therefore, all these models may be subject to the identified unsafe condition. We are considering similar rulemaking for these additional models. Differences Between the Proposed AD and the Service Information Boeing Service Bulletin 737–53–1310, dated October 20, 2011, specifies to contact the manufacturer for disposition of certain repair conditions, but this proposed AD would require repairing those conditions in one of the following ways: • In accordance with a method that we approve; or • Using data that meet the certification basis of the airplane, and that have been approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) whom we have authorized to make those findings. Tables 2 through 7 in paragraph 1.E., ‘‘Compliance,’’ of Boeing Service Bulletin 737–53–1310, dated October 20, 2011, specify post-modification inspections at certain chem-mill step locations, which may be used in support of compliance with section 121.1109(c)(2) or 129.109(c)(2) of the Federal Aviation Regulations (14 CFR 121.1109(c)(2) or 129.109(c)(2)). However, this NPRM does not propose to require those post-modification inspections. This difference has been coordinated with Boeing. Costs of Compliance We estimate that this proposed AD affects 545 airplanes of U.S. registry. We estimate the following costs to comply with this proposed AD: ESTIMATED COSTS Action Labor cost Parts cost Cost per product Inspection of chem-mill step locations. 37 work-hours × $85 per hour = $3,145 per inspection cycle. None ... $3,145 per inspection cycle ...... We have received no definitive data that would enable us to provide cost estimates for the on-condition actions specified in this proposed AD. mstockstill on DSK4VPTVN1PROD with PROPOSALS Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. VerDate Mar<15>2010 16:53 Sep 17, 2012 Jkt 226001 We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on PO 00000 Frm 00014 Fmt 4702 Sfmt 4702 Cost on U.S. operators $1,714,025 per inspection cycle. products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. E:\FR\FM\18SEP1.SGM 18SEP1 57538 Federal Register / Vol. 77, No. 181 / Tuesday, September 18, 2012 / Proposed Rules For the reasons discussed above, I certify this proposed regulation: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): The Boeing Company: Docket No. FAA– 2012–0936; Directorate Identifier 2011– NM–269–AD. (a) Comments Due Date We must receive comments by November 2, 2012. (b) Affected ADs None. (c) Applicability This AD applies to The Boeing Company Model 737–700 and –700C series airplanes, as identified in Boeing Service Bulletin 737– 53–1310, dated October 20, 2011. mstockstill on DSK4VPTVN1PROD with PROPOSALS (d) Subject Joint Aircraft System Component (JASC)/ Air Transport Association (ATA) of America Code 53, Fuselage. (e) Unsafe Condition This AD was prompted by reports of early fatigue cracks at chem-mill areas on the crown skin panels. We are issuing this AD to detect and correct fatigue cracking of the skin panel at the specified chem-mill step locations, which could result in rapid decompression of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. VerDate Mar<15>2010 16:53 Sep 17, 2012 Jkt 226001 (g) Inspections At the applicable time specified in paragraph 1.E., ‘‘Compliance,’’ of Boeing Service Bulletin 737–53–1310, dated October 20, 2011, except as required by paragraph (j) of this AD: Do an external detailed inspection and an external non-destructive inspection (a medium frequency eddy current (MFEC), magneto optic imager (MOI), C-scan, or ultrasonic phased array (UTPA) inspection) for cracking in the fuselage skin along the chem-mill steps at certain locations specified in, and in accordance with, Boeing Service Bulletin 737–53–1310, dated October 20, 2011. Repeat the inspections required by paragraph (g) of this AD thereafter at the applicable times specified in paragraph 1.E., ‘‘Compliance,’’ of Boeing Service Bulletin 737–53–1310, dated October 20, 2011. (h) Repair If any cracking is found during any inspection required by paragraph (g) of this AD, before further flight, repair the cracking using a method approved in accordance with the procedures specified in paragraph (l) of this AD. Accomplishing the repair approved in accordance with the procedures specified in paragraph (l) of this AD terminates the repetitive inspection requirement for that area under the repair only. (i) Optional Terminating Modification Modification of an inspection area, including an external detailed inspection and an external non-destructive inspection (MFEC, MOI, C-scan, or UTPA) for cracking of the area to be modified, and a high frequency eddy current inspection of all existing holes for cracking, in accordance with the Accomplishment Instructions of Boeing Service Bulletin 737–53–1310, dated October 20, 2011, terminates the repetitive inspections required by paragraph (g) of this AD for that area only. If any cracking is found during any inspection described by this paragraph, before further flight, repair the cracking using a method approved in accordance with the procedures specified in paragraph (l) of this AD. (j) Service Bulletin Exception Boeing Service Bulletin 737–53–1310, dated October 20, 2011, specifies compliance times ‘‘after the original issue date of this service bulletin.’’ However, this AD requires compliance within the specified compliance times ‘‘after the effective date of this AD.’’ (k) Post-Modification Inspections The post-modification inspections specified in Tables 2 through 7 of paragraph 1.E., ‘‘Compliance,’’ of Boeing Service Bulletin 737–53–1310, dated October 20, 2011, are not required by this AD. Note 1 to paragraph (k) of this AD: The damage tolerance inspections specified in Tables 2 through 7 of paragraph 1.E., ‘‘Compliance,’’ of Boeing Service Bulletin 737–53–1310, dated October 20, 2011, may be used in support of compliance with section 121.1109(c)(2) or 129.109(c)(2) of the Federal Aviation Regulations (14 CFR 121.1109(c)(2) or 14 CFR 129.109(c)(2)). The actions specified in Part 5 of the Accomplishment Instructions and PO 00000 Frm 00015 Fmt 4702 Sfmt 9990 corresponding figures of Boeing Service Bulletin 737–53–1310, dated October 20, 2011, are not required by this AD. (l) Alternative Methods of Compliance (AMOCs) (1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. Information may be emailed to: 9-ANMSeattle-ACO-AMOC-Requests@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO, to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane, and the approval must specifically refer to this AD. (m) Related Information (1) For more information about this AD, contact Wayne Lockett, Aerospace Engineer, Airframe Branch, ANM–120S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, Washington 98057– 3356; phone: (425) 917–6447; fax: (425) 917– 6590; email: Wayne.Lockett@faa.gov. (2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H–65, Seattle, WA 98124–2207; telephone 206– 544–5000, extension 1; fax 206–766–5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221. Issued in Renton, Washington, on September 4, 2012. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2012–22891 Filed 9–17–12; 8:45 am] BILLING CODE 4910–13–P E:\FR\FM\18SEP1.SGM 18SEP1

Agencies

[Federal Register Volume 77, Number 181 (Tuesday, September 18, 2012)]
[Proposed Rules]
[Pages 57536-57538]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2012-22891]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012-0936; Directorate Identifier 2011-NM-269-AD]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
certain The Boeing Company Model 737-700 and -700C series airplanes. 
This proposed AD was prompted by reports of early fatigue cracks at 
chem-mill areas on the crown skin panels. This proposed AD would 
require repetitive inspections for cracking of the fuselage skin at 
certain locations at chem-mill areas, and repair if necessary. We are 
proposing this AD to detect and correct fatigue cracking of the skin 
panel at the specified chem-mill step locations, which could result in 
rapid decompression of the airplane.

DATES: We must receive comments on this proposed AD by November 2, 
2012.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 
11.43 and 11.45, by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: Deliver to Mail address above between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate; 1601 Lind 
Avenue SW., Renton, Washington. For information on the availability of 
this material at the FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at  https://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES 
section. Comments will be available in the AD docket shortly after 
receipt.

FOR FURTHER INFORMATION CONTACT: Wayne Lockett, Aerospace Engineer, 
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 
1601 Lind Avenue SW., Renton, Washington 98057-3356; phone: (425) 917-
6447; fax: (425) 917-6590; email: Wayne.Lockett@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposal. Send your comments to an address listed 
under the ADDRESSES section. Include ``Docket No. FAA-2012-0936; 
Directorate Identifier 2011-NM-269-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    We received reports of early fatigue cracks near chem-mill areas on 
the crown skin panels of Model 737-300, -400, and -500 series 
airplanes. The cracks resulted from high stresses in the areas where 
chem-mill pockets are adjacent to non-chem-mill areas.

[[Page 57537]]

Although we have not received any reports of this type of fuselage 
fatigue cracks on Model 737-600, -700, -700C, -800, -900, or -900ER 
series airplanes, a full-scale fatigue test article was inspected for 
skin cracks at similar structural details and two chem-mill cracks were 
found that occurred late in the testing program. This condition, if not 
detected and corrected, could result in rapid decompression of the 
airplane.

Relevant Service Information

    We reviewed Boeing Service Bulletin 737-53-1310, dated October 20, 
2011, for Model 737-700 and -700C series airplanes. That service 
bulletin describes, among other things, procedures for doing repetitive 
external detailed inspections and external non-destructive inspections 
(medium frequency eddy current (MFEC), magneto optic imager (MOI), C-
scan, or ultrasonic phased array (UTPA) inspections) of the fuselage 
skin at specified locations where chem-mill areas are adjacent to non-
chem-mill areas at antenna and door bearstrap installations, and 
repairs if necessary.
    Boeing Service Bulletin 737-53-1310, dated October 20, 2011, also 
describes procedures for installing modification doublers, which 
involves an external detailed inspection and an external non-
destructive (MFEC, MOI, C-scan, or UTPA) inspection for any cracking of 
the area to be modified prior to the doubler being placed on that area, 
a high frequency eddy current inspection of all existing holes for 
cracking, and contacting Boeing if necessary. That service bulletin 
also specifies that when a modification is accomplished, the repetitive 
inspection for the area under the modification is no longer necessary.
    Boeing Service Bulletin 737-53-1310, dated October 20, 2011, 
specifies an initial compliance time of 43,000 total flight cycles, or 
1,500 flight cycles after the original issue date of that service 
bulletin, whichever occurs later. That service bulletin specifies a 
repetitive interval not to exceed 1,500 flight cycles or 2,100 flight 
cycles, depending on inspection method.
    For airplanes that have incorporated Boeing Business Jet (BBJ) 
lower cabin altitude supplemental type certificate (STC) ST010697SE, 
all initial compliance times specified in flight cycles must be reduced 
to half of those specified in that service bulletin, and all repeat 
interval compliance times specified in flight cycles must be reduced to 
one-quarter of those specified in that service bulletin.+

FAA's Determination

    We are proposing this AD because we evaluated all the relevant 
information and determined the unsafe condition described previously is 
likely to exist or develop in other products of the same type design.

Proposed AD Requirements

    This proposed AD would require accomplishing the actions specified 
in the service information described previously, except as discussed 
under ``Differences Between the Proposed AD and the Service 
Information.''

Similar Rulemaking

    The crown skin panels on Model 737-700 and -700C series airplanes 
are of a similar design to those on Model 737-300, -400, -500, -600, -
800, -900, and -900ER series airplanes. Therefore, all these models may 
be subject to the identified unsafe condition. We are considering 
similar rulemaking for these additional models.

Differences Between the Proposed AD and the Service Information

    Boeing Service Bulletin 737-53-1310, dated October 20, 2011, 
specifies to contact the manufacturer for disposition of certain repair 
conditions, but this proposed AD would require repairing those 
conditions in one of the following ways:
     In accordance with a method that we approve; or
     Using data that meet the certification basis of the 
airplane, and that have been approved by the Boeing Commercial 
Airplanes Organization Designation Authorization (ODA) whom we have 
authorized to make those findings.
    Tables 2 through 7 in paragraph 1.E., ``Compliance,'' of Boeing 
Service Bulletin 737-53-1310, dated October 20, 2011, specify post-
modification inspections at certain chem-mill step locations, which may 
be used in support of compliance with section 121.1109(c)(2) or 
129.109(c)(2) of the Federal Aviation Regulations (14 CFR 
121.1109(c)(2) or 129.109(c)(2)). However, this NPRM does not propose 
to require those post-modification inspections. This difference has 
been coordinated with Boeing.

Costs of Compliance

    We estimate that this proposed AD affects 545 airplanes of U.S. 
registry.
    We estimate the following costs to comply with this proposed AD:

                                                 Estimated costs
----------------------------------------------------------------------------------------------------------------
                                                                                                 Cost on U.S.
              Action                    Labor cost        Parts  cost     Cost per product        operators
----------------------------------------------------------------------------------------------------------------
Inspection of chem-mill step       37 work-hours x $85  None..........  $3,145 per           $1,714,025 per
 locations.                         per hour = $3,145                    inspection cycle.    inspection cycle.
                                    per inspection
                                    cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition actions specified in this proposed 
AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.

[[Page 57538]]

    For the reasons discussed above, I certify this proposed 
regulation:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new 
airworthiness directive (AD):

The Boeing Company: Docket No. FAA-2012-0936; Directorate Identifier 
2011-NM-269-AD.

(a) Comments Due Date

We must receive comments by November 2, 2012.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to The Boeing Company Model 737-700 and -700C 
series airplanes, as identified in Boeing Service Bulletin 737-53-
1310, dated October 20, 2011.

(d) Subject

    Joint Aircraft System Component (JASC)/Air Transport Association 
(ATA) of America Code 53, Fuselage.

(e) Unsafe Condition

    This AD was prompted by reports of early fatigue cracks at chem-
mill areas on the crown skin panels. We are issuing this AD to 
detect and correct fatigue cracking of the skin panel at the 
specified chem-mill step locations, which could result in rapid 
decompression of the airplane.

(f) Compliance

    Comply with this AD within the compliance times specified, 
unless already done.

(g) Inspections

    At the applicable time specified in paragraph 1.E., 
``Compliance,'' of Boeing Service Bulletin 737-53-1310, dated 
October 20, 2011, except as required by paragraph (j) of this AD: Do 
an external detailed inspection and an external non-destructive 
inspection (a medium frequency eddy current (MFEC), magneto optic 
imager (MOI), C-scan, or ultrasonic phased array (UTPA) inspection) 
for cracking in the fuselage skin along the chem-mill steps at 
certain locations specified in, and in accordance with, Boeing 
Service Bulletin 737-53-1310, dated October 20, 2011. Repeat the 
inspections required by paragraph (g) of this AD thereafter at the 
applicable times specified in paragraph 1.E., ``Compliance,'' of 
Boeing Service Bulletin 737-53-1310, dated October 20, 2011.

(h) Repair

    If any cracking is found during any inspection required by 
paragraph (g) of this AD, before further flight, repair the cracking 
using a method approved in accordance with the procedures specified 
in paragraph (l) of this AD. Accomplishing the repair approved in 
accordance with the procedures specified in paragraph (l) of this AD 
terminates the repetitive inspection requirement for that area under 
the repair only.

(i) Optional Terminating Modification

    Modification of an inspection area, including an external 
detailed inspection and an external non-destructive inspection 
(MFEC, MOI, C-scan, or UTPA) for cracking of the area to be 
modified, and a high frequency eddy current inspection of all 
existing holes for cracking, in accordance with the Accomplishment 
Instructions of Boeing Service Bulletin 737-53-1310, dated October 
20, 2011, terminates the repetitive inspections required by 
paragraph (g) of this AD for that area only. If any cracking is 
found during any inspection described by this paragraph, before 
further flight, repair the cracking using a method approved in 
accordance with the procedures specified in paragraph (l) of this 
AD.

(j) Service Bulletin Exception

    Boeing Service Bulletin 737-53-1310, dated October 20, 2011, 
specifies compliance times ``after the original issue date of this 
service bulletin.'' However, this AD requires compliance within the 
specified compliance times ``after the effective date of this AD.''

(k) Post-Modification Inspections

    The post-modification inspections specified in Tables 2 through 
7 of paragraph 1.E., ``Compliance,'' of Boeing Service Bulletin 737-
53-1310, dated October 20, 2011, are not required by this AD.

    Note 1 to paragraph (k) of this AD:  The damage tolerance 
inspections specified in Tables 2 through 7 of paragraph 1.E., 
``Compliance,'' of Boeing Service Bulletin 737-53-1310, dated 
October 20, 2011, may be used in support of compliance with section 
121.1109(c)(2) or 129.109(c)(2) of the Federal Aviation Regulations 
(14 CFR 121.1109(c)(2) or 14 CFR 129.109(c)(2)). The actions 
specified in Part 5 of the Accomplishment Instructions and 
corresponding figures of Boeing Service Bulletin 737-53-1310, dated 
October 20, 2011, are not required by this AD.

(l) Alternative Methods of Compliance (AMOCs)

    (1) The Manager, Seattle Aircraft Certification Office (ACO), 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in the Related Information 
section of this AD. Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD if it is approved by the 
Boeing Commercial Airplanes Organization Designation Authorization 
(ODA) that has been authorized by the Manager, Seattle ACO, to make 
those findings. For a repair method to be approved, the repair must 
meet the certification basis of the airplane, and the approval must 
specifically refer to this AD.

(m) Related Information

    (1) For more information about this AD, contact Wayne Lockett, 
Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft 
Certification Office, 1601 Lind Avenue SW., Renton, Washington 
98057-3356; phone: (425) 917-6447; fax: (425) 917-6590; email: 
Wayne.Lockett@faa.gov.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-
5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may review copies of the referenced 
service information at the FAA, Transport Airplane Directorate, 1601 
Lind Avenue SW., Renton, Washington. For information on the 
availability of this material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on September 4, 2012.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2012-22891 Filed 9-17-12; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.