Department of Transportation May 28, 2009 – Federal Register Recent Federal Regulation Documents

This action proposes to establish Class E airspace at Plentywood Sher-Wood Airport, Plentywood, MT. Controlled airspace is necessary to accommodate aircraft using a new Area Navigation (RNAV) Global Positioning System (GPS) Standard Instrument Approach Procedure (SIAP) at Plentywood Sher-Wood Airport, Plentywood, MT. The FAA is proposing this action to enhance the safety and management of aircraft operations at Plentywood Sher-Wood Airport, Plentywood, MT.

The Federal Highway Administration is issuing this revised Notice of Intent to advise the public of changes to the logical termini for the Environmental Impact Statement that will be prepared to study improvements to State Route 15/State Route 57 to provide a four-lane facility beginning in the vicinity of the State Route 67/I-110 Interchange in Harrison County, Mississippi and terminating on State Route 15 north of Beaumont, Mississippi, a distance of approximately 61 miles. The original Notice of Intent for this project appeared in the July 17, 2008 Federal Register.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) for Eurocopter Deutschland GmbH (Eurocopter) Model EC135 helicopters. This AD results from a report of abnormal main rotor blade vibrations on a Eurocopter Model EC135 helicopter. This AD also results from mandatory continuing airworthiness information (MCAI) issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI states that an operator reported unusual vibrations during the start phase of the main rotor blade on one helicopter. The vibrations stopped after the application of torque. Subsequent maintenance personnel found that six of the eight attachment screws of the lower hub-shaft bearing support were loose. This condition was discovered in two additional helicopters. Loose screws in the bearing support, if not detected and corrected, could result in abnormal main rotor blade vibrations and subsequent damage to the main transmission.

This establishes, amends, suspends, or revokes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

We are adopting a new airworthiness directive (AD) to supersede AD 2008-12-16, which applies to certain M7 Aerospace LP SA226 and SA227 series airplanes. AD 2008-12-16 currently requires you to inspect wires and tube assemblies for chafing, arcing, or insufficient clearance between components. If chafing, arcing, or insufficient clearance between components is found, AD 2008-12-16 requires you to clear, repair, and/or replace all chafed wires, components, and tube assemblies. AD 2008-12-16 also requires you to cover the four-gauge wires leaving the battery box with firesleeving and secure them with a clamp. Since we issued AD 2008-12-16, M7 Aerospace LP has notified us that Model SA227-BC (C-26A) was inadvertently left out of the Applicability section of the AD, and they updated some of the service information due to parts availability. Operators have also identified issues with model applicability that needed clarification. Consequently, this AD retains the actions of AD 2008-12-16, adds Model SA227-BC (C-26A) to the Applicability section, and regroups the models for clarification. We are issuing this AD to detect and correct chafing of electrical wires, components, and tube assemblies. This condition could result in arcing of exposed wires with consequent burning of a hole in a hydraulic line or the bleed air line. This failure could lead to a hydraulic fluid leak and a possible fire in the engine nacelle compartment.