Department of Transportation November 25, 2008 – Federal Register Recent Federal Regulation Documents
Results 1 - 18 of 18
Sixth Meeting, Special Committee 214: Standards for Air Traffic Data Communication Services, Working Group 78 (WG-78)
The FAA is issuing this notice to advise the public of a sixth meeting of RTCA Special Committee 214, Standards for Air Traffic Data Communication Services.
Proposed Establishment of Class E Airspace; Tower, MN
This action proposes to establish Class E airspace at Tower, MN. Controlled airspace is necessary to accommodate new Standard Instrument Approach Procedures (SIAPs) at Tower Municipal Airport, Tower, MN. The FAA is taking this action to enhance the safety and management of Instrument Flight Rules (IFR) aircraft operations at Tower Municipal Airport.
Receipt of Application for a Temporary Exemption From Advanced Air Bag Requirements of FMVSS No. 208
In accordance with the procedures in 49 CFR Part 555, Modena Design SpA has petitioned the agency for a temporary exemption from certain advanced air bag requirements of FMVSS No. 208. The basis for the application is that compliance would cause substantial economic hardship to a manufacturer that has tried in good faith to comply with the standard.\1\
Petition for Exemption From the Vehicle Theft Prevention Standard; Ford Motor Company
This document grants in full the petition of Ford Motor Company (Ford) in accordance with Sec. 543.9(c)(2) of 49 CFR Part 543, Exemption from the Theft Prevention Standard, for the Ford Mercury Mariner vehicle line beginning with model year (MY) 2010. This petition is granted because the agency has determined that the antitheft device to be placed on the line as standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the Theft Prevention Standard.
Mercedes-Benz, U.S.A. LLC; Receipt of Application for Extension of a Temporary Exemption From Federal Motor Vehicle Safety Standard No. 108
In accordance with the procedures of 49 CFR 555.6(b), Mercedes-Benz, U.S.A. LLC (``MBUSA''), on behalf of its parent corporation Daimler AG (``Daimler'') has applied for a renewal of a temporary exemption from S5.5.10 of Federal Motor Vehicle Safety Standard (FMVSS) No. 108. The basis of the application is to continue the development and field evaluation of new motor vehicle safety feature providing a level of safety at least equal to that of the standard. We are publishing this notice of receipt of the application in accordance with the requirements of 49 CFR 555.7(a), and have made no judgment on the merits of the application.
Environmental Impact Statement: Proposed Improvements to State Route 126 (Memorial Boulevard) From East Center Street in Kingsport, to Interstate 81, Sullivan County, TN
The Federal Highway Administration (FHWA) is issuing this notice to advise the public that an Environmental Impact Statement (EIS) will be prepared for a proposed highway project in Sullivan County, Tennessee.
Environmental Impact Statement; Knox County, City of Vincennes, IN and Lawrence County, IL
The Federal Highway Administration (FHWA) is issuing this revised notice to advise the public that FHWA will not be preparing an Environmental Impact Statement (EIS) for the proposed relocation of railroad lines in Knox County, Indiana and Lawrence County, Illinois. A ``Notice of Intent'' to prepare an EIS was published in the Federal Register on March 16, 2007.
Proposed Agency Information Collection Activities; Comment Request
In accordance with the Paperwork Reduction Act of 1995 and its implementing regulations, the Federal Railroad Administration (FRA) hereby announces that it is seeking an extension of the following currently approved information collection activities. These information collection activities received a six-month emergency approval from OMB. FRA seeks this extension while it works on developing a proposed rule related to the same topic of inappropriate cell phone use and other electronic/electrical devices by railroad employees while on-duty. Before submitting these information collection requirements for clearance by the Office of Management and Budget (OMB), FRA is soliciting public comment on specific aspects of the activities identified below.
Airworthiness Directives; Agusta S.p.A. Model A109A and A109A II Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Agusta S.p.A. (Agusta) model helicopters. This AD results from a revised mandatory continuing airworthiness information (MCAI) issued by an aviation authority to identify and correct an unsafe condition on an aviation product. The aviation authority of Italy, with which we have a bilateral agreement, reports that the previous MCAI should not apply to newly redesigned and improved tail rotor blades. This AD requires the same inspections as the current AD but limits the applicability to only three part-numbered tail rotor blades. This AD requires actions that are intended to prevent fatigue failure of a tail rotor blade (blade), loss of a tail rotor, and subsequent loss of control of the helicopter.
Airworthiness Directives; Eurocopter France Model AS355E, F, F1, F2, and N Helicopters
This amendment supersedes an existing airworthiness directive (AD) for the specified Eurocopter France (Eurocopter) model helicopters. That AD currently requires certain checks of the magnetic chip detector plug (chip detector) and the main gearbox (MGB) oil-sight glass, certain inspections of the lubrication pump (pump), and replacing the MGB and the pump with an airworthy MGB and pump, if necessary. Also, the AD requires that before a pump or MGB with any hours time-in-service (TIS) can be installed, it must meet the AD requirements. This AD adds all serial-numbered pumps to the applicability and requires using an improved procedure for detecting oil pump wear. This amendment is prompted by additional cases of MGB lubrication pump deterioration and a further investigation that determined that all serial-numbered pumps might be affected and the development of an improved procedure that is more accurate for detecting oil pump wear earlier. The actions specified by this AD are intended to implement improved procedures to detect a failing MGB oil pump, prevent failure of the MGB pump, seizure of the MGB, loss of drive to an engine and main rotor, and subsequent loss of control of the helicopter.
Airworthiness Directives; Boeing Model 737-400, -500, -600, -700, -700C, -800, and -900 Series Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-400, -500, -600, -700, -700C, -800, and -900 series airplanes. This AD requires an inspection to determine the part and serial numbers of the windshield wiper motors for the pilot's and first officer's windshields, and doing applicable corrective actions. This AD results from two reports that the left and right windshield wipers stopped working in flight. We are issuing this AD to prevent failure of the windshield wipers in wet weather, which could result in decreased visibility for the flightcrew.
Airworthiness Directives; Maule Aerospace Technology, Inc. M-4, M-5, M-6, and M-7 Series and Model M-8-235 Airplanes
The FAA adopts a new airworthiness directive (AD) for certain Maule Aerospace Technology, Inc. M-4, M-5, M-6, and M-7 series and Model M-8-235 airplanes. This AD requires you to paint the top of the rear elevator control horn, the elevator control cable end attached to the top of the rear control horn, the bottom of the forward elevator control horn, and the elevator control cable end attached to the bottom of the forward control horn. This AD also requires you to insert a supplement into your maintenance program (maintenance manual). This AD results from two reports of accidents where reversed elevator control rigging was a factor. We are issuing this AD to reduce the likelihood of a mechanic rigging the elevator controls backwards, which could result in elevator movement in the opposite direction from control input. This condition could lead to loss of control.
Airworthiness Directives; Viking Air Limited DHC-6 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Over-the-Road Bus Accessibility Program Grant Program: Corrections to Project ID Numbers
This notice revises Project Identification Numbers published in the August 22, 2008, Federal Transit Administration (FTA) notice titled ``Over-the-Road Bus Accessibility Program Announcement of Project Selections.'' The notice identifies corrections to Fiscal Year (FY) 2007 and 2008 Project Identification Numbers; however, award amounts remain unchanged.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ 190 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Boeing Model 757 Airplanes
We are adopting a new airworthiness directive (AD) for certain Boeing Model 757 airplanes. This AD requires sealing the fasteners on the front and rear spars inside the left and right main fuel tanks and on the rear spar and lower panel of the center fuel tank. This AD also requires inspections of the wire bundle support installations to verify if certain clamps are installed and if Teflon sleeving covers the wire bundles inside the left and right equipment cooling system bays, on the left and right rear spars, and on the left and right front spars; and corrective actions if necessary. This AD results from a fuel system review conducted by the manufacturer. We are issuing this AD to detect and correct improper wire bundle support installation and sleeving and to prevent improperly sealed fasteners in the main and center fuel tanks from becoming an ignition source, in the event of a fault current, which could result in a fuel tank explosion and consequent loss of the airplane.
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
