Department of Transportation November 14, 2008 – Federal Register Recent Federal Regulation Documents
Results 1 - 22 of 22
Helicopter Emergency Medical Services Operations
This notice announces the availability of and requests comments on revisions to Operations Specification A021, pertaining to Helicopter Emergency Medical Services (HEMS) operations, and Operation Specification A050, pertaining to Helicopter Night Vision Goggle Operations (HNVGO).
United We Ride State/Tribal Mobility Management Coordination Grants; Solicitation for Proposals and Technical Assistance/Training Available
This notice solicits proposals from States and tribal associations or consortia for United We Ride (UWR) mobility management grants. This solicitation is issued by the Federal Transit Administration (FTA) on behalf of the Federal Interagency Coordinating Council on Access and Mobility (CCAM). Funding in the amount of $1.5 million is provided by FTA to support grants ranging up to $300,000 each. These grants are intended to assist States and tribal associations in supporting the development of transportation coordination capabilities and capacity within local or regional human service networks to address the individualized customer transportation needs of persons and families with low income, persons with disabilities, older adults and youth. Specifically, these grants seek to address individual customer needs for mobility within workforce development, health care, aging, youth, disability, education, housing, veterans and other social service or human service support networks. State or tribal mobility management proposals may include the development of educational programs, training and technical assistance activities, and mobility management coordination pilots for or within such networks. These grants are not intended to fund the capital or operating costs of specific transportation services or transportation brokerage programs. The projects proposed should represent new or expanded activities, not just the maintenance of existing actions already being funded. FTA-funded technical assistance and training programs are described that may prove helpful to applicants in either developing or implementing proposals.
Airworthiness Directives; Avidyne Corporation Primary Flight Displays (Part Numbers 700-00006-000, -001, -002, -003, and -100)
We propose to supersede Airworthiness Directive (AD) 2008-06- 28 R1, which applies to certain Avidyne Corporation (Avidyne) Primary Flight Displays (PFDs) (part numbers (P/Ns) 700-00006-000, -001, -002, -003, and -100) that are installed on airplanes. AD 2008-06-28 R1 currently requires you to do a check of the maintenance records and inspection of the PFD (if necessary) to determine if an affected serial number PFD is installed and incorporate (if necessary) operational limitations. Since we issued AD 2008-06-28 R1, Avidyne developed a factory service procedure that will correct the problems on these Avidyne PFDs and also factory serviced certain serial number PFDs. Consequently, this proposed AD would retain the actions from AD 2008- 06-28 R1 until the affected PFD is factory serviced; add the actions of a label or marking check, an air data system performance verification test, and (if necessary) replacement of the PFD and factory servicing of the failed PFD; and reduce the serial number applicability from that of AD 2008-06-28 R1. We are proposing this AD to prevent certain conditions from existing when PFDs display incorrect attitude, altitude, and airspeed information. This could result in airspeed/ altitude mismanagement or spatial disorientation of the pilot with consequent loss of airplane control, inadequate traffic separation, or controlled flight into terrain.
Airworthiness Directives; General Electric Co. (GE) CF6-80A Series Turbofan Engines
The FAA proposes to adopt a new airworthiness directive (AD) for GE CF6-80A series turbofan engines with a high-pressure turbine rotor (HPTR) stage 1 disk, part number (P/N) 9367M45G06, installed. This proposed AD would require removing any HPTR stage 1 disk, P/N 9367M45G06, before exceeding 2,075 cycles-since-new (CSN). This proposed AD results from an error by GE that incorrectly cited a cyclic life of 12,600 CSN for the HPTR stage 1 disk, P/N 9367M45G06. We are proposing this AD to prevent the HPTR stage 1 disk from exceeding its part life which could cause fatigue cracks to start and grow. These cracks could result in a possible uncontained disk failure and damage to the airplane.
Qualification of Drivers; Exemption Applications; Vision
FMCSA announces its decision to renew the exemptions from the vision requirement in the Federal Motor Carrier Safety Regulations for 14 individuals. FMCSA has statutory authority to exempt individuals from the vision requirement if the exemptions granted will not compromise safety. The Agency has concluded that granting these exemption renewals will provide a level of safety that is equivalent to, or greater than, the level of safety maintained without the exemptions for these commercial motor vehicle (CMV) drivers.
Norfolk Southern Railway Company, Pan Am Railways Inc., et al.-Joint Control and Operating/Pooling Agreements-Pan Am Southern LLC
On May 30, 2008, Norfolk Southern Railway Company (Norfolk Southern), Pan Am Railways, Inc. (PARI), Boston and Maine Corporation (B&M) and Springfield terminal Railway company (Springfield Terminal) (collectively, Applicants) filed a petition with the Surface Transportation Board (Board) seeking Board approval under 49 U.S.C. 11322 and 11323 of (1) the acquisition by Norfolk Southern and B&M of joint control and ownership of Pan Am Southern, LLC (PAS), a new rail carrier to be formed; and (2) the agreements by which Springfield Terminal would operate the lines of PAS and establish rates for PAS. The agreements for which approval and authorization are being sought by the application and the related filings will be referred to collectively as the Transaction. The Board, through its Section of Environmental Analysis (SEA), is the lead agency responsible for the preparation of the Environmental Assessment (EA). If the Transaction is approved, PAS would own or operate over (through trackage rights) approximately 437 miles of existing rail lines (referred to in the application as the PAS Lines), comprised of approximately 238.4 miles of existing rail lines to be owned by PAS and approximately 198.4 miles of existing track over which PAS would have trackage rights. Norfolk Southern would contribute capital to PAS which would go into improving infrastructure by creating a new intermodal and automotive facility in Mechanicville, NY (the Mechanicville Facility), creating a new automotive facility in Ayer, MA (San Vel Automotive Facility), making minor improvements at an existing intermodal facility at Ayer (Ayer Intermodal), and enhancing other infrastructure along the existing east-west main line. The Transaction also includes acquisition and/or operation by PAS of six other existing rail yards in addition to the three facilities at which some construction would occur. The Transaction does not contemplate any yard improvements or changes in activity at any of these six rail yards. Based on the information provided from all sources to date and its independent analysis, SEA preliminarily concludes that construction and operation of the two proposed new rail facilities and improvements to an existing rail facility and existing rail lines would not have significant environmental impacts if the Board imposes and Applicants implement the recommended mitigation measures set forth in the EA. Copies of the EA have been served on all interested parties and will be made available to additional parties upon request. The entire EA is also available for review on the Board's Web site (https:// www.stb.dot.gov) by going to ``E-LIBRARY,'' clicking on the ``Decisions and Notices'' link, and then searching by the Service Date (November 14, 2008) or Docket Number (FD 35147). SEA will consider all comments received in making its final recommendations to the Board. The Board will then consider SEA's final recommendations and the complete environmental record in making its final decision in this proceeding.
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. The existing AD currently requires inspecting to identify the wing anti-ice ducts (piccolo tubes) in the wing leading edge. For airplanes with affected piccolo tubes, the existing AD requires revising the airplane flight manual (AFM) to introduce new procedures for operation in icing conditions. The existing AD provides an optional implementation of repetitive inspections for cracks of affected piccolo tubes, and corrective actions if necessary, which terminates the operational limitations. The existing AD also provides an optional installation of certain new piccolo tubes, which terminates both the AFM revision and the inspections. This AD adds airplanes to the applicability, requires revising the AFM to introduce new procedures for operation in icing conditions, and requires inspecting to determine if certain anti-ice piccolo ducts are installed, and replacing or repairing the piccolo duct if necessary. This AD also provides an optional terminating action of replacing all affected piccolo ducts. This AD results from reports of failed piccolo tubes. We are issuing this AD to prevent cracked piccolo tubes, which could result in air leakage, a possible adverse effect on the anti-ice air distribution pattern and anti-ice capability without annunciation to the flight crew, and consequent reduced controllability of the airplane.
Airworthiness Directives; Pratt & Whitney (PW) Models PW2037, PW2037(M), and PW2040 Turbofan Engines
The FAA proposes to adopt a new airworthiness directive (AD) for PW models PW2037, PW2037(M), and PW2040 turbofan engines. This proposed AD would require inspecting all high-pressure turbine (HPT) 2nd stage hubs at the next HPT overhaul after the effective date of the proposed AD. The inspections of the hubs include fluorescent penetrant inspection (FPI) for cracks and an optical comparator inspection (OCI) of the blade retention slots to confirm the hubs are within dimensional tolerances before returning them to service. This proposed AD results from an uncontained release of HPT 2nd stage blades and blade retention lugs. We are proposing this AD to detect cracks and remove nonconforming HPT 2nd stage hubs, which could result in an uncontained release of turbine blades and blade retention lugs, and damage to the airplane.
Notice of Intent To Rule on Request To Release Airport Property at the Eagle County Regional Airport, Eagle, CO
The FAA proposes to rule and invite public comment on the release of land at the Eagle County Regional Airport under the provisions of Section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21).
Notice of Final Federal Agency Actions on Proposed Highway in Michigan
This notice announces the availability of a Record of Decision by FHWA pursuant to the requirements of the National Environmental Protection Policy Act of 1969 (NEPA), 42 U.S.C. 4321, as amended and the Council on Environmental Quality Regulations (40 CFR parts 1500- 1508). In addition, this notice announces actions taken by FHWA and other Federal agencies that are final with in the meaning of 23 U.S.C. 139(l)(1). These actions relate to a proposed highway project, US-131 in St. Joseph County, Michigan. These actions grant approvals for the project.
Airworthiness Directives; Rolls-Royce plc RB211 Trent 553-61, 553A2-61, 556-61, 556A2-61, 556B-61, 556B2-61, 560-61, and 560A2-61 Turbofan Engines
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as affecting only RB211 Trent 500 series turbofan engines that have not incorporated Rolls-Royce plc (RR) Service Bulletin (SB) No. RB.211-72-D733, dated August 21, 2002, or Revision 1 of that SB, dated March 6, 2008, as follows:
Airworthiness Directives; Airbus Model A318, A319, A320, and A321 Airplanes
The FAA is superseding an existing airworthiness directive (AD), which applies to certain Airbus Model A318, A319, A320, and A321 airplanes. That AD currently requires inspecting to determine the part number and serial number of the fuel tank boost pumps and, for airplanes with affected pumps, revising the airplane flight manual (AFM) and the FAA-approved maintenance program. The existing AD also provides for optional terminating action for compliance with the revisions to the AFM and the maintenance program. This new AD requires modifying or replacing the fuel tank boost pumps, which would terminate the AFM limitations and the maintenance program revisions. This AD results from a report that a fuel tank boost pump failed in service, due to a detached screw of the boost pump housing that created a short circuit between the stator and rotor of the boost pump motor and tripped a circuit breaker. We are issuing this AD to prevent electrical arcing in the fuel tank boost pump motor, which, in the presence of a combustible air-fuel mixture in the pump, could result in an explosion and loss of the airplane.
Airworthiness Directives; Boeing Model 737-100, -200, -200C, -300, -400, and -500 Series Airplanes
The FAA is revising an existing airworthiness directive (AD) that applies to certain Boeing Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. That AD currently requires various repetitive inspections for cracking of the upper frame to side frame splice of the fuselage, and other specified and corrective actions if necessary. That AD also provides for an optional preventive modification, which terminates the repetitive inspections. This new AD adds an optional terminating action that was inadvertently omitted from that AD. This AD results from a report that the upper frame of the fuselage was severed between stringers S-13L and S-14L at station 747, and the adjacent frame at station 767 had a 1.3-inch-long crack at the same stringer location. We are issuing this AD to detect and correct fatigue cracking of the upper frame to side frame splice of the fuselage, which could result in reduced structural integrity of the frame and adjacent lap joint. This reduced structural integrity can increase loading in the fuselage skin, which will accelerate skin crack growth and result in decompression of the airplane.
Airworthiness Directives; Allied Ag Cat Productions, Inc. Model G-164 Series Airplanes
The FAA adopts a new airworthiness directive (AD) to supersede AD 78-08-09, which applies to certain Allied Ag Cat Productions, Inc. (formerly Grumman-American) (Allied Ag Cat) Models G-164, G-164A, and G-164B airplanes. AD 78-08-09 currently requires repetitively inspecting the interior and the exterior of the main tubular spar of the rudder assembly for corrosion, taking necessary corrective action if corrosion is found, and applying corrosion protection. Since we issued AD 78-08-09, the rudder main tubular spar failed on a later production airplane. Consequently, this AD retains the actions required in AD 78-08-09 and expands the applicability to include all G-164 series airplanes. We are issuing this AD to detect and correct corrosion in the rudder main tubular spar, which could result in failure of the weld to the main spar tube. This failure could lead to loss of directional control.
Airworthiness Directives; Boeing Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, and 747SR Series Airplanes
The FAA is superseding an existing airworthiness directive (AD) that applies to certain Boeing Model 747 series airplanes. That AD currently requires repetitive inspections for cracking and corrosion of all exposed surfaces of the carriage spindles (including the inner bore and aft links) of the trailing edge flaps, and additional inspection and corrective action if necessary. That AD also currently requires repetitive overhaul of the carriage spindle and aft link, which terminates the repetitive inspections. This new AD adds a repetitive inspection to detect broken parts, and revises the overhaul threshold and repetitive intervals. This AD results from analysis that showed additional inspections should be done to prevent the loss of a flap, and that the flight-hour-based interval should be revised to a flight- cycle-based interval, because the greatest loads on the spindles happen during takeoff and landing. We are issuing this AD to detect and correct failed carriage spindles or aft links of the inboard or outboard trailing edge flaps. Such failure could cause the flap to depart the airplane, reducing the flightcrew's ability to maintain the safe flight and landing of the airplane.
Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB-135 Airplanes, and Model EMB-145, -145ER, -145MR, -145LR, -145XR, -145MP, and -145EP Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Airbus Model A318, A319, A320, and A321 Series Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
Airworthiness Directives; Dassault Model Mystere-Falcon 900, Falcon 900EX, and Falcon 2000 Airplanes
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
This site is protected by reCAPTCHA and the Google
Privacy Policy and
Terms of Service apply.
