January 21, 2016 – Federal Register Recent Federal Regulation Documents

This action amends Class E airspace at El Paso, TX. Closure of West Texas Airport has made this action necessary for continued safety and management within the National Airspace System. Additionally, the geographic coordinates for El Paso International Airport and Biggs Army Airfield (AAF), are adjusted correctly noted in the Rule section of this document. This does not affect the boundaries or operating requirements of the airspace.

We are revising airworthiness directive (AD) 2015-12-09 for Airbus Helicopters Model EC135P1, EC135T1, EC135P2, EC135T2, EC135P2+, EC135T2+, and MBB-BK 117 C-2 helicopters. AD 2015-12-09 required inspecting certain washers for movement and making the appropriate repairs if the washers move. As published, AD 2015-12-09 referenced an incorrect date for the service information in the Credit for Previous Actions section. This AD corrects the error while retaining the requirements of AD 2015-12-09. These actions are intended to prevent loss of concerned control axis and subsequent loss of control of the helicopter.

We are adopting a new airworthiness directive (AD) for Airbus Helicopters Deutschland GmbH (AHD) (previously Eurocopter Deutschland GmbH) Model MBB-BK 117 A-1, A-3, A-4, B-1, B-2, C-1, and C-2 helicopters. This AD requires an initial and recurring inspection of the N2 control arm and, depending on the outcome of the inspection, repairing or replacing the N2 control arm. This AD was prompted by a report of a heavily corroded and broken N2 control arm. The actions of this AD are intended to detect corrosion, a crack, or a scratch in the N2 control arm, which could lead to failure of the N2 control arm, a drop in rotor speed, and subsequent loss of control of the helicopter.

We are superseding Airworthiness Directive (AD) 2002-23-20, for certain Dassault Aviation Model FALCON 900EX and MYSTERE-FALCON 900 airplanes. AD 2002-23-20 required repetitive operational tests of the flap asymmetry detection system to verify proper functioning, and repair if necessary; repetitive replacement of the inboard flap jackscrews with new or reconditioned jackscrews; and repetitive measurement of the screw/nut play of the jackscrews on the inboard and outboard flaps to detect discrepancies, and corrective action if necessary. AD 2002-23-20 also required a revision of the airplane flight manual. Since we issued AD 2002-23-20, the maintenance manual has been revised. This AD requires revising the maintenance or inspection program, as applicable, to include the maintenance tasks and airworthiness limitations specified in the Airworthiness Limitations section of the airplane maintenance manual. This AD also removes the Model FALCON 900EX airplanes from the applicability. We are issuing this AD to prevent reduced structural integrity of the airplane.

We are adopting a new airworthiness directive (AD) for all Airbus Model A310 and Airbus Model A300 B4-600, B4-600R, and F4-600R series airplanes; and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This AD was prompted by a report of skin disbonding and damage found on the composite side panel of the rudder, located between the rudder core and skin of a previously repaired area. This AD requires an inspection for disbonding or damage of certain rudders, and related investigative actions and corrective actions if necessary. We are issuing this AD to detect and correct disbonding and damage of the rudder, which could result in reduced structural integrity of the rudder and consequent reduced controllability of the airplane.

We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports of fluid entry and accumulation in the aft equipment bay. This AD requires modifying the aft equipment bay. We are issuing this AD to prevent excessive quantities of flammable fluid accumulation in the aft equipment bay. Flammable fluid entry and accumulation in the aft equipment bay, in excessive quantities, could exceed safe levels maintained by the drainage and ventilation system.