Emergency Response and Preparedness, 32199-32200 [2014-12928]
Download as PDF
<![CDATA[
Federal Register / Vol. 79, No. 107 / Wednesday, June 4, 2014 / Proposed Rules
§ 39.13
(f) Installation Prohibition
[Amended]
2. The FAA amends § 39.13 by
removing airworthiness directive (AD)
2013–15–09, Amendment 39–17525 (78
FR 49111, August 13, 2013), and adding
the following new AD:
■
Pratt & Whitney Division: Docket No. FAA–
2013–0072; Directorate Identifier 2013–
NE–04–AD.
(a) Comments Due Date
The FAA must receive comments on this
AD action by August 4, 2014.
(b) Affected ADs
This AD supersedes AD 2013–15–09,
Amendment 39–17525 (78 FR 49111, August
13, 2013).
(c) Applicability
This AD applies to all Pratt & Whitney
Division (PW) PW4074, PW4074D, PW4077,
PW4077D, PW4084D, PW4090, and PW4090–
3 turbofan engine models with second-stage
high-pressure turbine (HPT) air seal, part
number (P/N) 54L041, 50L960, or 50L976,
installed.
ehiers on DSK2VPTVN1PROD with PROPOSALS
(d) Unsafe Condition
This AD was prompted by additional
reports of cracking in the second-stage HPT
air seal. We are issuing this AD to prevent
failure of the second-stage HPT air seal,
which could lead to uncontained engine
failure and damage to the airplane.
(e) Compliance
Comply with this AD within the
compliance times specified, unless already
done.
(1) At the next piece-part exposure after the
effective date of this AD, do the following:
(i) Remove from service second-stage HPT
air seals, P/N 50L960, 50L976, and 50L041.
(ii) Fluorescent-penetrant inspect (FPI)
second-stage HPT air seal, P/N 50L041, for a
through-crack in the front forward fillet
radius.
(iii) If a through-crack in the front forward
fillet radius is found, remove the first-stage
HPT hub, second-stage HPT hub, and secondstage HPT blade retaining plate from service.
Do not reinstall the first-stage HPT hub,
second-stage HPT hub, or second-stage HPT
blade retaining plate into any engine.
(2) For engines with second-stage HPT air
seals, P/N 50L041, installed, perform initial
and repetitive inspections for cracks on-wing
until the part is removed from the engine as
follows:
(i) Perform an initial eddy current
inspection (ECI) for cracks prior to reaching
2,200 cycles-since-new or within 100 cyclesin-service after the effective date of this AD,
whichever occurs later.
(ii) Thereafter, repeat the ECI every 1,200
cycles since last inspection, or fewer,
depending on the results of the inspection.
(iii) Use section 4.0 of the appendix of PW
Alert Service Bulletin (ASB) No. PW4G–112–
A72–330, Revision 2, dated July 11, 2013, to
perform the inspection and use paragraph 8
of the Accomplishment Instructions of PW
ASB No. PW4G–112–A72–330, Revision 2,
dated July 11, 2013, to disposition the results
of the inspection.
VerDate Mar<15>2010
14:53 Jun 03, 2014
Jkt 232001
DEPARTMENT OF LABOR
After the effective date of this AD, do not
install any second-stage HPT air seal P/N
50L041, P/N 50L960, or P/N 50L976 into any
engine.
32199
Occupational Safety and Health
Administration
(g) Definitions
(1) For the purpose of this AD, piece-part
exposure is when the second-stage HPT air
seal is removed from the engine and fully
disassembled.
(2) For the purpose of this AD, a throughcrack is a crack that has propagated through
the thickness of the part and can be seen on
both the inner diameter and outer diameter
of the front forward fillet radius.
29 CFR Part 1910
[Docket Number: OSHA–2007–0073]
RIN 1218–AC17
Emergency Response and
Preparedness
Occupational Safety and Health
Administration (OSHA), Labor.
ACTION: Notice of stakeholder meeting.
AGENCY:
OSHA invites interested
parties to participate in an informal
stakeholder meeting on emergency
response and preparedness. OSHA
plans to use the information obtained at
the stakeholder meeting as it considers
the development of a proposed standard
for emergency response and
preparedness.
SUMMARY:
(h) Credit for Previous Actions
(1) If you performed an ECI of the secondstage HPT air seal before the effective date of
this AD, using PW ASB No. PW4G–112–
A72–330, Revision 1, dated February 14,
2013, or earlier version, you have met the
requirements of paragraph (e)(2)(i) of this AD.
(2) If you performed an in-shop FPI of the
second-stage HPT air seal before the effective
date of this AD, you have met the
requirements of paragraph (e)(2)(i) of this AD.
The Manager, Engine Certification Office,
FAA, may approve AMOCs for this AD. Use
the procedures found in 14 CFR 39.19 to
make your request.
Date and location for the
stakeholder meeting are: July 30, 2014,
at 9:00 a.m., in Washington, DC. If
needed, a second session will be held
July 31, 2014.
The deadline to request registration
for the meeting is July 2, 2014.
ADDRESSES:
(j) Related Information
I. Registration
(i) Alternative Methods of Compliance
(AMOCs)
(1) For more information about this AD,
contact James Gray, Aerospace Engineer,
Engine Certification Office, FAA, Engine &
Propeller Directorate, 12 New England
Executive Park, Burlington, MA 01803;
phone: (781) 238–7742; fax: (781) 238–7199;
email: james.e.gray@faa.gov.
(2) For service information identified in
this AD, contact Pratt & Whitney Division,
400 Main St., East Hartford, CT 06108;
phone: (860) 565–8770; fax: (860) 565–4503.
(3) You may view this service information
at the FAA, Engine & Propeller Directorate,
12 New England Executive Park, Burlington,
MA. For information on the availability of
this material at the FAA, call (781) 238–7125.
Issued in Burlington, Massachusetts, on
May 28, 2014.
Colleen M. D’Alessandro,
Assistant Directorate Manager, Engine &
Propeller Directorate, Aircraft Certification
Service.
[FR Doc. 2014–12973 Filed 6–3–14; 8:45 am]
BILLING CODE 4910–13–P
PO 00000
Frm 00028
Fmt 4702
Sfmt 4702
DATES:
Submit your request to attend the
stakeholder meeting by one of the
following methods:
• Electronic. Register at https://
ersregistration.pec1.net/ (follow the
instructions online).
• Facsimile. Fax your request to (240)
686–3959 and label it ‘‘Attention: OSHA
Emergency Response and Preparedness
Stakeholder Meeting Registration.’’
• Regular or express mail, hand
delivery, or messenger (courier) service.
Send your request, postmarked by July
2, to: Project Enhancement Corporation,
20300 Century Blvd. Ste. 175,
Germantown, MD 20874; Attention:
OSHA Emergency Response and
Preparedness Stakeholder Meeting
Registration.
II. Stakeholder Meeting
The stakeholder meeting will be held
at the Frances Perkins Building, 200
Constitution Avenue NW., Washington,
DC, 20210.
FOR FURTHER INFORMATION CONTACT:
Information regarding this notice is
available from the following sources:
• Press inquiries. Contact Frank
Meilinger, Director, OSHA Office of
Communications, Room N–3647, U.S.
Department of Labor, 200 Constitution
Avenue NW., Washington, DC, 20210;
E:\FR\FM\04JNP1.SGM
04JNP1
32200
Federal Register / Vol. 79, No. 107 / Wednesday, June 4, 2014 / Proposed Rules
telephone: (202) 693–1999; email:
Meilinger.Francis2@dol.gov.
• General and technical information.
Contact Mat Chibbaro or Bill Hamilton,
Fire Protection Engineers, Office of
Safety Systems, OSHA Directorate of
Standards and Guidance, Room N–3609,
U.S. Department of Labor, 200
Constitution Avenue NW., Washington,
DC, 20210; telephone: (202) 693–2255;
email: Chibbaro.Mat@dol.gov or
Hamilton.Bill@dol.gov.
• Copies of this Federal Register
notice. Electronic copies are available at
https://www.regulations.gov. This
Federal Register notice, as well as news
releases and other relevant information
and documents, also are available on the
OSHA Web page at https://
www.osha.gov.
SUPPLEMENTARY INFORMATION:
ehiers on DSK2VPTVN1PROD with PROPOSALS
I. Background
Emergency response is one of the
most hazardous occupations in America
(see the National Fire Protection
Association report ‘‘Firefighter Fatalities
in the United States—2012’’ and the
2012 Federal Emergency Management
Agency report ‘‘Firefighter Fatalities in
the United States in 2012’’). Emergency
responders include firefighters,
emergency medical service personnel,
hazardous material employees, and
technical rescue specialists. Also, law
enforcement officers usually are
considered emergency responders
because they often assist in emergency
response incidents. OSHA notes,
however, that there are no standards
issued by the Agency that specifically
address occupational hazards uniquely
related to law enforcement activities.
Many emergency responders have cross
training in these specialties, and may
serve in multiple roles depending upon
the type of emergency incident
involved. Skilled support employees are
not emergency responders, but
nonetheless have specialized training
that can be important to the safe and
successful resolution of an emergency
incident.
The Agency issued a Request for
Information (RFI) (74 FR 51735, Sept.
11, 2007) that solicited comments from
the public to evaluate what action, if
any, the Agency should take to further
address emergency response and
preparedness. Recent events, such as the
April 2013 tragedy in West, Texas, that
killed several emergency responders,
and an analysis of the information
provided in response to the 2007 RFI,
make it clear that emergency responder
health and safety continues to be an area
of ongoing concern. Accordingly, OSHA
determined it would be beneficial to
VerDate Mar<15>2010
14:53 Jun 03, 2014
Jkt 232001
hold a stakeholder meeting to gather
additional information. OSHA plans to
use the information received in
response to the 2007 RFI and obtained
at this stakeholder meeting when
considering a proposed standard for
emergency response and preparedness.
II. Stakeholder Meeting
OSHA will conduct the stakeholder
meeting as a group discussion
addressing views, concerns, and issues
surrounding emergency response and
preparedness. To facilitate as much
group interaction as possible, OSHA is
not permitting formal presentations.
OSHA will focus the meeting on major
issues such as scope and approach.
OSHA will provide participants with
additional information on the major
issues for discussion prior to the
meeting.
III. Public Participation
The meeting will accommodate about
20 participants. Members of the general
public (if registered) may observe, but
not participate in, the meeting if space
permits. OSHA staff will be present to
take part in the discussions. PEC
Solutions, Inc. (PEC) is managing the
logistics for the meeting. Accordingly,
PEC will provide a facilitator and
compile notes summarizing the
discussion; these notes will list
participants and their affiliations, but
will not attribute specific comments to
individual speakers. PEC also will make
an audio recording of each session to
ensure that the summary notes are
accurate, but will not transcribe these
recordings. OSHA will post the
summary notes in the docket for this
rulemaking, Docket No. OSHA 2007–
0073; the docket is available at https://
www.regulations.gov and OSHA’s
Docket Office.
The meeting will take place July 30,
2014, from 9:00 a.m. to 4:00 p.m., at the
Frances Perkins Building, 200
Constitution Avenue NW., Washington,
DC, 20210. Based on the number of
interested participants, OSHA may hold
a second meeting on July 31, 2014.
To participate in the stakeholder
meeting, or to be a nonparticipating
observer, you must submit a request
using one of the three methods specified
above under ADDRESSES by the deadline
specified under DATES. OSHA will select
participants to ensure a fair
representation of interests and diverse
viewpoints, and will send you
confirmation of your registration no
later than one week prior to the meeting.
OSHA will not accommodate walk-in
attendees at the meeting. When
submitting your request, please provide
the following information:
PO 00000
Frm 00029
Fmt 4702
Sfmt 4702
• Name, address, phone, fax, and
email;
• Organization for which you work;
• Organization you represent (if
different);
• Participant or nonparticipating
observer; and
• Stakeholder category: public fire/
rescue service, federal fire/rescue
service, contract fire/rescue service,
private fire brigade, emergency medical
service, technical rescue, emergency
management, law enforcement, other
(please specify).
Authority and Signature
David Michaels, Ph.D., MPH,
Assistant Secretary of Labor for
Occupational Safety and Health, U.S.
Department of Labor, authorized the
preparation of this notice pursuant to 29
U.S.C. 653, 655, and 657, Secretary of
Labor’s Order No. 1–2012 (77 FR 3912;
Jan. 25, 2012), and 29 CFR part 1911.
Signed at Washington, DC, on May 28,
2014.
David Michaels,
Assistant Secretary of Labor for Occupational
Safety and Health.
[FR Doc. 2014–12928 Filed 6–3–14; 8:45 am]
BILLING CODE 4510–26–P
ENVIRONMENTAL PROTECTION
AGENCY
40 CFR Part 52
[EPA–R07–OAR–2014–0290; FRL–9911–73–
Region 7]
Approval and Promulgation of
Implementation Plans; State of
Missouri; Infrastructure SIP
Requirements for the 2008 Lead
National Ambient Air Quality Standard
Environmental Protection
Agency (EPA).
ACTION: Proposed rule.
AGENCY:
The Environmental Protection
Agency (EPA) is proposing to approve
elements of a State Implementation Plan
(SIP) submission from the State of
Missouri addressing the applicable
requirements of Clean Air Act (CAA)
section 110 for the 2008 National
Ambient Air Quality Standards
(NAAQS) for Lead (Pb), which requires
that each state adopt and submit a SIP
to support implementation,
maintenance, and enforcement of each
new or revised NAAQS promulgated by
EPA. These SIPs are commonly referred
to as ‘‘infrastructure’’ SIPs. The
infrastructure requirements are designed
to ensure that the structural components
of each state’s air quality management
SUMMARY:
E:\FR\FM\04JNP1.SGM
04JNP1
]]>Agencies
[Federal Register Volume 79, Number 107 (Wednesday, June 4, 2014)]
[Proposed Rules]
[Pages 32199-32200]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-12928]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Occupational Safety and Health Administration
29 CFR Part 1910
[Docket Number: OSHA-2007-0073]
RIN 1218-AC17
Emergency Response and Preparedness
AGENCY: Occupational Safety and Health Administration (OSHA), Labor.
ACTION: Notice of stakeholder meeting.
-----------------------------------------------------------------------
SUMMARY: OSHA invites interested parties to participate in an informal
stakeholder meeting on emergency response and preparedness. OSHA plans
to use the information obtained at the stakeholder meeting as it
considers the development of a proposed standard for emergency response
and preparedness.
DATES: Date and location for the stakeholder meeting are: July 30,
2014, at 9:00 a.m., in Washington, DC. If needed, a second session will
be held July 31, 2014.
The deadline to request registration for the meeting is July 2,
2014.
ADDRESSES:
I. Registration
Submit your request to attend the stakeholder meeting by one of the
following methods:
Electronic. Register at https://ersregistration.pec1.net/
(follow the instructions online).
Facsimile. Fax your request to (240) 686-3959 and label it
``Attention: OSHA Emergency Response and Preparedness Stakeholder
Meeting Registration.''
Regular or express mail, hand delivery, or messenger
(courier) service. Send your request, postmarked by July 2, to: Project
Enhancement Corporation, 20300 Century Blvd. Ste. 175, Germantown, MD
20874; Attention: OSHA Emergency Response and Preparedness Stakeholder
Meeting Registration.
II. Stakeholder Meeting
The stakeholder meeting will be held at the Frances Perkins
Building, 200 Constitution Avenue NW., Washington, DC, 20210.
FOR FURTHER INFORMATION CONTACT: Information regarding this notice is
available from the following sources:
Press inquiries. Contact Frank Meilinger, Director, OSHA
Office of Communications, Room N-3647, U.S. Department of Labor, 200
Constitution Avenue NW., Washington, DC, 20210;
[[Page 32200]]
telephone: (202) 693-1999; email: Meilinger.Francis2@dol.gov.
General and technical information. Contact Mat Chibbaro or
Bill Hamilton, Fire Protection Engineers, Office of Safety Systems,
OSHA Directorate of Standards and Guidance, Room N-3609, U.S.
Department of Labor, 200 Constitution Avenue NW., Washington, DC,
20210; telephone: (202) 693-2255; email: Chibbaro.Mat@dol.gov or
Hamilton.Bill@dol.gov.
Copies of this Federal Register notice. Electronic copies
are available at https://www.regulations.gov. This Federal Register
notice, as well as news releases and other relevant information and
documents, also are available on the OSHA Web page at https://www.osha.gov.
SUPPLEMENTARY INFORMATION:
I. Background
Emergency response is one of the most hazardous occupations in
America (see the National Fire Protection Association report
``Firefighter Fatalities in the United States--2012'' and the 2012
Federal Emergency Management Agency report ``Firefighter Fatalities in
the United States in 2012''). Emergency responders include
firefighters, emergency medical service personnel, hazardous material
employees, and technical rescue specialists. Also, law enforcement
officers usually are considered emergency responders because they often
assist in emergency response incidents. OSHA notes, however, that there
are no standards issued by the Agency that specifically address
occupational hazards uniquely related to law enforcement activities.
Many emergency responders have cross training in these specialties, and
may serve in multiple roles depending upon the type of emergency
incident involved. Skilled support employees are not emergency
responders, but nonetheless have specialized training that can be
important to the safe and successful resolution of an emergency
incident.
The Agency issued a Request for Information (RFI) (74 FR 51735,
Sept. 11, 2007) that solicited comments from the public to evaluate
what action, if any, the Agency should take to further address
emergency response and preparedness. Recent events, such as the April
2013 tragedy in West, Texas, that killed several emergency responders,
and an analysis of the information provided in response to the 2007
RFI, make it clear that emergency responder health and safety continues
to be an area of ongoing concern. Accordingly, OSHA determined it would
be beneficial to hold a stakeholder meeting to gather additional
information. OSHA plans to use the information received in response to
the 2007 RFI and obtained at this stakeholder meeting when considering
a proposed standard for emergency response and preparedness.
II. Stakeholder Meeting
OSHA will conduct the stakeholder meeting as a group discussion
addressing views, concerns, and issues surrounding emergency response
and preparedness. To facilitate as much group interaction as possible,
OSHA is not permitting formal presentations. OSHA will focus the
meeting on major issues such as scope and approach. OSHA will provide
participants with additional information on the major issues for
discussion prior to the meeting.
III. Public Participation
The meeting will accommodate about 20 participants. Members of the
general public (if registered) may observe, but not participate in, the
meeting if space permits. OSHA staff will be present to take part in
the discussions. PEC Solutions, Inc. (PEC) is managing the logistics
for the meeting. Accordingly, PEC will provide a facilitator and
compile notes summarizing the discussion; these notes will list
participants and their affiliations, but will not attribute specific
comments to individual speakers. PEC also will make an audio recording
of each session to ensure that the summary notes are accurate, but will
not transcribe these recordings. OSHA will post the summary notes in
the docket for this rulemaking, Docket No. OSHA 2007-0073; the docket
is available at https://www.regulations.gov and OSHA's Docket Office.
The meeting will take place July 30, 2014, from 9:00 a.m. to 4:00
p.m., at the Frances Perkins Building, 200 Constitution Avenue NW.,
Washington, DC, 20210. Based on the number of interested participants,
OSHA may hold a second meeting on July 31, 2014.
To participate in the stakeholder meeting, or to be a
nonparticipating observer, you must submit a request using one of the
three methods specified above under ADDRESSES by the deadline specified
under DATES. OSHA will select participants to ensure a fair
representation of interests and diverse viewpoints, and will send you
confirmation of your registration no later than one week prior to the
meeting. OSHA will not accommodate walk-in attendees at the meeting.
When submitting your request, please provide the following information:
Name, address, phone, fax, and email;
Organization for which you work;
Organization you represent (if different);
Participant or nonparticipating observer; and
Stakeholder category: public fire/rescue service, federal
fire/rescue service, contract fire/rescue service, private fire
brigade, emergency medical service, technical rescue, emergency
management, law enforcement, other (please specify).
Authority and Signature
David Michaels, Ph.D., MPH, Assistant Secretary of Labor for
Occupational Safety and Health, U.S. Department of Labor, authorized
the preparation of this notice pursuant to 29 U.S.C. 653, 655, and 657,
Secretary of Labor's Order No. 1-2012 (77 FR 3912; Jan. 25, 2012), and
29 CFR part 1911.
Signed at Washington, DC, on May 28, 2014.
David Michaels,
Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2014-12928 Filed 6-3-14; 8:45 am]
BILLING CODE 4510-26-P
