Federal Motor Vehicle Safety Standards, 73383 [05-55519]
Download as PDF
73383
Federal Register / Vol. 70, No. 237 / Monday, December 12, 2005 / Rules and Regulations
Dated: November 18, 2005.
Richard E. Greene,
Regional Administrator, Region 6.
I
Authority: 42 U.S.C. 7401 et seq.
adding one new entry to the end of the
table to read as follows:
Subpart SS—Texas
40 CFR part 52 is amended as follows:
PART 52—[AMENDED]
1. The authority citation for part 52
continues to read as follows:
I
§ 52.2270
2. In § 52.2270, the table in paragraph
(e) entitled ‘‘EPA approved
nonregulatory provisions and quasiregulatory measures’’ is amended by
I
*
Identification of plan.
*
*
(e) * * *
*
*
EPA APPROVED NONREGULATORY PROVISIONS AND QUASI-REGULATORY MEASURES IN THE TEXAS SIP
Applicable geographic
or nonattainment area
Name of SIP provision
*
*
*
*
Memorandum of Understanding Between the Statewide .....................
Texas Department of Transportation and the
Texas Natural Resource Conservation Commission.
[FR Doc. 05–23915 Filed 12–9–05; 8:45 am]
BILLING CODE 6560–50–P
State approval/submittal date
EPA approval date
*
08/15/2002
*
12/12/2005 [Insert FR
page number where
document begins].
DEPARTMENT OF COMMERCE
National Oceanic and Atmospheric
Administration
DEPARTMENT OF TRANSPORTATION
50 CFR Part 622
[Docket No. 050314071–5230–02; I.D.
030105E]
National Highway Traffic Safety
Administration
RIN 0648–AS16
49 CFR Part 571
Federal Motor Vehicle Safety
Standards
Fisheries of the Caribbean, Gulf of
Mexico, and South Atlantic; Shrimp
Fishery Off the Southern Atlantic
States; Amendment 6
CFR Correction
AGENCY:
In Title 49 of the Code of Federal
Regulations, Parts 400 to 599, revised as
of October 1, 2005, on page 384, in
§ 571.111, add S9.4 to read as follows:
§ 571.111
mirrors.
Standard No. 111; Rearview
*
*
*
*
*
S9.4(a) Each image required by
S9.3(a)(1) to be visible at the driver’s eye
location shall be separated from the
edge of the effective mirror surface of
the mirror providing that image by a
distance of not less than 3 minutes of
arc.
(b) The image required by S9.3(a)(1) of
cylinder P shall meet the following
requirements:
(1) The angular size of the shortest
dimension of that cylinder’s image shall
be not less than 3 minutes of arc; and
(2) The angular size of the longest
dimension of that cylinder’s image shall
be not less than 9 minutes of arc.
*
*
*
*
*
[FR Doc. 05–55519 Filed 12–9–05; 8:45 am]
BILLING CODE 1505–01–D
VerDate Aug<31>2005
15:45 Dec 09, 2005
Jkt 208001
National Marine Fisheries
Service (NMFS), National Oceanic and
Atmospheric Administration (NOAA),
Commerce.
ACTION: Final rule.
SUMMARY: NMFS issues this final rule to
implement Amendment 6 to the Fishery
Management Plan for the Shrimp
Fishery of the South Atlantic Region
(FMP), as prepared and submitted by
the South Atlantic Fishery Management
Council (Council). This final rule
requires an owner or operator of a
trawler that harvests or possesses
penaeid shrimp (brown, pink, or white
shrimp) in or from the exclusive
economic zone (EEZ) off the southern
Atlantic states to obtain a commercial
vessel permit for South Atlantic penaeid
shrimp; requires an owner or operator of
a vessel in the South Atlantic rock
shrimp or penaeid shrimp fishery to
submit catch and effort reports and to
carry an observer on selected trips; and
requires bycatch reduction devices
(BRDs) in nets in the rock shrimp
fishery. In addition, this final rule
removes provisions of the regulations
applicable to other fisheries off the
southern Atlantic states that are no
PO 00000
Frm 00037
Fmt 4700
Sfmt 4700
Comments
*
longer applicable and makes minor
corrections. Amendment 6 also
establishes stock status determination
criteria for South Atlantic penaeid
shrimp; revises the specifications of
maximum sustainable yield (MSY) and
optimum yield (OY) for South Atlantic
rock shrimp; revises the stock status
determination criteria for South Atlantic
rock shrimp; revises the bycatch
reduction criterion for the certification
of BRDs; and transfers from the Council
to the Regional Administrator,
Southeast Region, NMFS (RA),
responsibilities for the specification of
the protocol for testing BRDs. In
addition, NMFS informs the public of
the approval by the Office of
Management and Budget (OMB) of the
collection-of-information requirements
contained in this final rule and
publishes the OMB control numbers for
those collections. The intended effects
of this rule are to provide additional
information for, and improve the
effective management of, the shrimp
fisheries off the southern Atlantic states
and to correct and clarify the regulations
applicable to other southern Atlantic
fisheries.
This final rule is effective
January 11, 2006, except for
§ 622.4(a)(2)(xiii) which is effective
April 11, 2006.
ADDRESSES: Copies of Final Regulatory
Flexibility Analysis (FRFA) and
Regulatory Impact Review (RIR) are
available from NMFS, Southeast
Regional Office, 263 13th Avenue
South, St. Petersburg, FL 33701;
telephone 727–824–5305; fax 727–824–
5308.
Comments regarding the burden-hour
estimates or other aspects of the
collection-of-information requirements
DATES:
E:\FR\FM\12DER1.SGM
12DER1
Agencies
[Federal Register Volume 70, Number 237 (Monday, December 12, 2005)]
[Rules and Regulations]
[Page 73383]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 05-55519]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration
49 CFR Part 571
Federal Motor Vehicle Safety Standards
CFR Correction
In Title 49 of the Code of Federal Regulations, Parts 400 to 599,
revised as of October 1, 2005, on page 384, in Sec. 571.111, add S9.4
to read as follows:
Sec. 571.111 Standard No. 111; Rearview mirrors.
* * * * *
S9.4(a) Each image required by S9.3(a)(1) to be visible at the
driver's eye location shall be separated from the edge of the effective
mirror surface of the mirror providing that image by a distance of not
less than 3 minutes of arc.
(b) The image required by S9.3(a)(1) of cylinder P shall meet the
following requirements:
(1) The angular size of the shortest dimension of that cylinder's
image shall be not less than 3 minutes of arc; and
(2) The angular size of the longest dimension of that cylinder's
image shall be not less than 9 minutes of arc.
* * * * *
[FR Doc. 05-55519 Filed 12-9-05; 8:45 am]
BILLING CODE 1505-01-D