June 15, 2005 – Federal Register Recent Federal Regulation Documents

The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-200, -300, and -400ER series airplanes. This AD requires an inspection to determine if the door-mounted escape slide/rafts have certain part numbers. For those door-mounted escape slide/rafts having certain part numbers, this AD requires an inspection for excessive tension of the firing cable, and procedures for providing slack in the firing cable or rerouting the firing cable if necessary. This AD is prompted by reports of uncommanded inflation inside the airplane of a door-mounted escape slide/raft located in the passenger compartment. We are issuing this AD to prevent injury to maintenance personnel, passengers, and crew during otherwise normal operating conditions and to prevent interference with evacuation of the airplane during an emergency, due to uncommanded inflation of a door-mounted escape slide/raft.

The FAA is adopting a new airworthiness directive (AD) for all Fokker Model F.28 Mark 0100 airplanes. This AD requires an inspection to determine the part number of the passenger service unit (PSU) panels for the PSU modification status, and corrective actions if applicable. This AD is prompted by reported incidents of smoke in the passenger compartment during flight. One of those incidents also included a burning smell and consequently led to emergency evacuation of the airplane. We are issuing this AD to prevent overheating of the PSU panel due to moisture ingress, which could result in smoke or fire in the passenger cabin.

The Federal Communications Commission, as part of its continuing effort to reduce paperwork burden invites the general public and other Federal agencies to take this opportunity to comment on the following information collection(s), as required by the Paperwork Reduction Act of 1995, Pub. L. 104-13. An agency may not conduct or sponsor a collection of information unless it displays a currently valid control number. No person shall be subject to any penalty for failing to comply with a collection of information subject to the Paperwork Reduction Act (PRA) that does not display a valid control number. Comments are requested concerning (a) Whether the proposed collection of information is necessary for the proper performance of the functions of the Commission, including whether the information shall have practical utility; (b) the accuracy of the Commission's burden estimate; (c) ways to enhance the quality, utility, and clarity of the information collected; and (d) ways to minimize the burden of the collection of information on the respondents, including the use of automated collection techniques or other forms of information technology.

OSHA is proposing to update the existing standard for the construction of electric power transmission and distribution installations and make it consistent with the more recently promulgated general industry standard addressing the maintenance and repair of electric power generation, transmission, and distribution lines and equipment. The proposal also makes some miscellaneous changes to both standards, including adding provisions related to host employers and contractors, flame resistant clothing, and training, and updates the construction standard for electrical protective equipment, makes it consistent with the corresponding general industry standard, and makes it applicable to construction generally. The existing rules for this type of work were issued in 1971. They are out of date and are not consistent with the more recent, corresponding rules for the operation and maintenance of electric power transmission and distribution systems. The revised standard would include requirements relating to enclosed spaces, working near energized parts, grounding for employee protection, work on underground and overhead installations, work in substations, and other special conditions and equipment unique to the transmission and distribution of electric energy. OSHA is also proposing a new standard on electrical protective equipment for the construction industry. The current standards for the design of electrical protective equipment, which apply only to electric power transmission and distribution work, adopt several national consensus standards by reference. The new standard would replace the incorporation of these out-of-date consensus standards with a set of performance-oriented requirements that is consistent with the latest revisions of these consensus standards and with the corresponding standard for general industry. Additionally, OSHA is proposing new requirements for the safe use and care of electrical protective equipment to complement the equipment design provisions. In addition, OSHA is proposing changes to the two corresponding general industry standards. These changes address: Class 00 rubber insulating gloves, electrical protective equipment made from materials other than rubber, training for electric power generation, transmission, and distribution workers, host-contractor responsibilities, job briefings, fall protection (including a requirement that employees in aerial lifts use harnesses), insulation and working position of employees working on or near live parts, protective clothing, minimum approach distances, deenergizing transmission and distribution lines and equipment, protective grounding, operating mechanical equipment near overhead power lines, and working in manholes and vaults. These changes would ensure that employers, where appropriate, face consistent requirements for work performed under the construction and general industry standards and would further protect employees performing electrical work covered under the general industry standards. The proposal would also update references to consensus standards in Sec. Sec. 1910.137 and 1910.269 and would add new appendices to help employers comply with provisions on protective clothing and the inspection of work positioning equipment. OSHA is also proposing to revise the general industry standard for foot protection. This standard has substantial application to employers performing work on electric power transmission and distribution installations, but that applies to employers in other industries as well. The proposal would remove the requirement for employees to wear protective footwear as protection against electric shock.

This document announces the effective date of the rule published on January 31, 2005. The rules adopted licensing and service rules for satellite earth stations on vessels (ESVs) in the C- and Ku- bands that will provide regulatory certainty to ESV licensees, while protecting existing users in the bands.

The Federal Communications Commission, as part of its continuing effort to reduce paperwork burden invites the general public and other Federal agencies to take this opportunity to comment on the following information collection(s), as required by the Paperwork Reduction Act (PRA) of 1995, Public Law 104-13. An agency may not conduct or sponsor a collection of information unless it displays a currently valid control number. No person shall be subject to any penalty for failing to comply with a collection of information subject to the Paperwork Reduction Act that does not display a valid control number. Comments are requested concerning (a) whether the proposed collection of information is necessary for the proper performance of the functions of the Commission, including whether the information shall have practical utility; (b) the accuracy of the Commission's burden estimate; (c) ways to enhance the quality, utility, and clarity of the information collected; and (d) ways to minimize the burden of the collection of information on the respondents, including the use of automated collection techniques or other forms of information technology.

In this document, the Commission seeks comments on whether to defer or eliminate the requirement in the rules that certain applications for equipment authorization received on or after January 1, 2005, specify 6.24 kHz capability.