Wyoming Administrative Code
Agency 020 - Environmental Quality, Dept. of
Sub-Agency 0011 - Water Quality
Chapter 28 - STANDARDS FOR ISSUING PERMITS FOR COMMERCIAL OILFIELD WASTE DISPOSAL FACILITIES
Section 28-14 - Incorporation by Reference

Universal Citation: WY Code of Rules 28-14

Current through September 21, 2024

(a) The following codes, standards, rules, and regulations referenced in this Chapter are incorporated by reference:

(i) ASTM International Standard D1004-13, Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting, April 1, 2013, referred to as "ASTM D1004-13";

(ii) ASTM International Standard D1203-16, Standard Test Methods for Volatile Loss from Plastics Using Activated Carbon Methods, April 1, 2016, referred to as "ASTM D1203-16";

(iii) ASTM International Standard D1204-14, Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature, March 1, 2014, referred to as "ASTM 1204-14";

(iv) ASTM International Standard D1505-18, Standard Test Method for Density of Plastics by the Density-Gradient Technique, May 10, 2018, referred to as "ASTM D1505-18";

(v) ASTM International Standard D1593-19, Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting, December 11, 2019, referred to as "ASTM D1593-19";

(vi) ASTM International Standard D1603-14, Standard Test Method for Carbon Black Content in Olefin Plastics, August 1, 2014, referred to as "ASTM D1603-14";

(vii) ASTM International Standard D1790-14, Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact, October 1, 2014, referred to as "ASTM D1790-14";

(viii) ASTM International Standard D3895-19, Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry, June 25, 2019, referred to as "ASTM D3895-19";

(ix) ASTM International Standard D4218-15, Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique, December 1, 2015, referred to as "ASTM D4218-15";

(x) ASTM International Standard D4833/D4833M-07(2013), Standard Test Method for Index Puncture Resistance of Geomembranes and Related Products, May 1, 2013, referred to as "ASTM D4833/D4833M-07(2013)";

(xi) ASTM International Standard D5199-12(2019), Standard Test Method for Measuring the Nominal Thickness of Geosynthetics, June 21, 2019, referred to as "ASTM D5199-12(2019)";

(xii) ASTM International Standard D5321/D5321M-20, Standard Test Method for Determining the Shear Strength of Soil-Geosynthetic and Geosynthetic-Geosynthetic Interfaces by Direct Shear, March 3, 2020, referred to as "ASTM D5321/D5321M-20";

(xiii) ASTM International Standard D5397-19a, Standard Test Method for Evaluation of Stress Crack Resistance of Polyolefin Geomembranes Using Notched Constant Tensile Load Test, October 18, 2019, referred to as "ASTM D5397-19a";

(xiv) ASTM International Standard D5596-03(2016), Standard Test Method For Microscopic Evaluation of the Dispersion of Carbon Black in Polyolefin Geosynthetics, June 1, 2016, referred to as "ASTM D5596-03(2016)";

(xv) ASTM International Standard D5721-08(2018), Standard Practice for Air-Oven Aging of Polyolefin Geomembranes, June 8, 2018, referred to as "ASTM D5721-08(2018)";

(xvi) ASTM International Standard D5885/D5885M-17, Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry, June 1, 2017, referred to as "ASTM D5885/D5885M-17";

(xvii) ASTM International Standard D5887/D5887M-16, Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter, September 1, 2016, referred to as "ASTM D5887/D5887M-16";

(xviii) ASTM International Standard D5888-19, Standard Guide for Storage and Handling of Geosynthetic Clay Liners, May 19, 2019, referred to as "ASTM D5888-19";

(xix) ASTM International Standard D5889/D5889M-18, Standard Practice for Quality Control of Geosynthetic Clay Liners, March 9, 2018, referred to as "ASTM D5889/D5889M-18";

(xx) ASTM International Standard D5890-19, Standard Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners, May 30, 2019, referred to as "ASTM D5890-19";

(xxi) ASTM International Standard D5891/D5891M-19, Standard Test Method for Fluid Loss of Clay Component of Geosynthetic Clay Liners, August 23, 2019, referred to as "ASTM D5891/D5891M-19";

(xxii) ASTM International Standard D5993-18, Standard Test Method for Measuring Mass per Unit Area of Geosynthetic Clay Liners, June 15, 2018, referred to as "ASTM D5993-18";

(xxiii) ASTM International Standard D5994/D5994M-10(2015)e1, Standard Test Method for Measuring Core Thickness of Textured Geomembranes, May 1, 2015, referred to as "ASTM D5994/D5994M-10(2015)e1";

(xxiv) ASTM International Standard D6072/D6072M-19, Standard Practice for Obtaining Samples of Geosynthetic Clay Liners, January 8, 2019, referred to as "ASTM D6072/D6072M-19";

(xxv) ASTM International Standard D6102-15, Standard Guide for Installation of Geosynthetic Clay Liners, May 1, 2015, referred to as "ASTM D6102-15";

(xxvi) ASTM International Standard D6243Standard, Test Method for Determining the Internal and Interface Shear Strength of Geosynthetic Clay Liner by the Direct Shear Method, January 1, 2016, referred to as "ASTM D6243";

(xxvii) ASTM International Standard D6243/D6243M-16, Standard Test Method for Determining the Internal and Interface Shear Strength of Geosynthetic Clay Liner by the Direct Shear Method, January 1, 2016, referred to as "ASTM D6243/D6243M-16";

(xxviii) ASTM International Standard D6392-12(2018), Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods, February 15, 2018, referred to as "ASTM D6392-12(2018)";

(xxix) ASTM International Standard D6495/D6495M-18, Standard Guide for Acceptance Testing Requirements for Geosynthetic Clay Liners, March 9, 2018, referred to as "ASTM D6495/D6495M-18";

(xxx) ASTM International Standard D6496/D6496M-19, Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners, May 9, 2019, referred to as "ASTM D6496/D6496M-19";

(xxxi) ASTM International Standard D6497/D6497M-02(2015)e1, Standard Guide for Mechanical Attachment of Geomembrane to Penetrations or Structures, May 1, 2015, referred to as "ASTM D6497/D6497M-02(2015)e1";

(xxxii) ASTM International Standard D6693/D6693M-04(2015)e1, Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes, May 1, 2015, referred to as "ASTM D6693/D6693M-04(2015)e1";

(xxxiii) ASTM International Standard D6768/D6768M-19, Standard Test Method for Tensile Strength of Geosynthetic Clay Liners, May 9, 2019, referred to as "ASTM D6768/D6768M-19";

(xxxiv) ASTM International Standard D6788-02(2017), Standard Specification for Repositionable Pressure-Sensitive Flags, September 1, 2017, referred to as "ASTM D6788-02(2017)";

(xxxv) ASTM International Standard D7238-06(2017), Standard Test Method for Effect of Exposure of Unreinforced Polyolefin Geomembrane Using Fluorescent UV Condensation Apparatus, July 1, 2017, referred to as "ASTM D7238-06(2017)";

(xxxvi) ASTM International Standard D7466/D7466M-10(2015)e1, Standard Test Method for Measuring Asperity Height of Textured Geomembranes, May 1, 2015, referred to as "ASTM D7466/D7466M-10(2015)e1";

(xxxvii) ASTM International Standard D751-19, Standard Test Methods for Coated Fabrics, May 22, 2019, referred to as "ASTM D751-19";

(xxxviii) ASTM International Standard D792-13, Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement, November 1, 2013, referred to as "ASTM D792-13";

(xxxix) ASTM International Standard D814-95(2020), Standard Test Method for Rubber Property-Vapor Transmission of Volatile Liquids, February 26, 2020, referred to as "ASTM D814-95(2020)";

(xxxx) ASTM International Standard D882-18, Standard Test Method for Tensile Properties of Thin Plastic Sheeting, August 16, 2018, referred to as "ASTM D882-18";

(xxxxi) Code of Federal Regulations 40 CFR § 261.4(b)(5), in effect as of July 28, 1994, available at: http://www.ecfr.gov;

(xxxxii) Geosynthetic Research Institute Standard Specification GRI-GCL3, Test Methods, Required Properties, and Testing Frequencies of Geosynthetic Clay Liners (GCLs), as revised on July 26, 2010, referred to as "GRI-GCL3";

(xxxxiii) Geosynthetic Research Institute Standard Specification GRI-GM9, Cold Weather Seaming of Geomembranes, as revised on January 10, 2013, referred to as "GRI-GM9";

(xxxxiv) Geosynthetic Research Institute Standard Specification GRI-GM13, Test Methods, Test Properties and Testing Frequency for High Density Polyethylene (HDPE) Smooth and Textured Geomembranes, as revised on January 6, 2016, referred to as "GRI-GM13";

(xxxxv) Test Methods for Evaluating Solid Waste: Physical/Chemical Methods Compendium (SW-846), published by the United States Environmental Protection Agency, as revised July 2014, referred to as "US EPA SW-846".

(b) For these rules incorporated by reference:

(i) The Environmental Quality Council has determined that incorporation of the full text in these rules would be cumbersome or inefficient given the length or nature of the rules.

(ii) This Chapter does not incorporate later amendments or editions of incorporated codes, standards, rules, and regulations.

(iii) All incorporated codes, standards, rules, and regulations are available for public inspection at the Department's Cheyenne office. Contact information for the Cheyenne office may be obtained at http://deq.wyoming.gov or from (307) 777-7937.

Disclaimer: These regulations may not be the most recent version. Wyoming may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.