Washington Administrative Code
Title 204 - State Patrol (Equipment) (See also Titles 212, 446 and 448)
Chapter 204-10 - Equipment standards
Section 204-10-022 - Body requirements
Current through Register Vol. 24-06, March 15, 2024
(1) Defroster and defogging devices: Every enclosed motor vehicle must be equipped with a device capable of defogging and defrosting the windshield area. Vehicles or exact replicas of vehicles manufactured prior to January 1938 are exempt from this requirement.
(2) Door latches: Every enclosed motor vehicle equipped with side doors leading directly into a compartment that contains one or more seating accommodations must be equipped with door latches which firmly and automatically secure the door when pushed closed and which allow each door to be opened both from the inside and outside.
(3) Hoodlatches: A front opening hood must be equipped with a primary and a secondary latching system to hold the hood in a closed position.
Hoods are optional equipment on vehicles defined as street rod vehicles, custom vehicles and kit vehicles.
(4) Enclosed passenger compartment: A motor vehicle with an enclosed passenger compartment and powered by an internal combustion engine must be constructed to prevent the entry of exhaust fumes into the passenger compartment.
(5) Floor pan: A motor vehicle must be equipped with a floor pan under the entire passenger compartment capable of supporting the weight of the number of occupants that the vehicle is designed to carry.
(6) Bumpers: A motor vehicle must be equipped with a bumper on both the front and rear of the vehicle with the exception of motor vehicles where the original or predominant body configuration, provided by a recognized manufacturer, did not include such bumper or bumpers in the design of the vehicle. For the relevant model year, bumpers must accommodate recognized manufacturer impact absorption systems pursuant to applicable SAE Bumper Standards or equivalent standards.
Bumpers are optional equipment on vehicles defined as street rod vehicles, custom vehicles and kit vehicles. Bumpers, unless specifically exempted above, must:
Front | Back | |
Passenger Vehicles and Neighborhood Electric Vehicles | 22 Inches | 22 Inches |
For Trucks: | ||
4,500 lbs. and under GVWR | 24 Inches | 26 Inches |
4,501 lbs. to 7,500 lbs. GVWR | 27 Inches | 29 Inches |
7,501 lbs. and over GVWR | 28 Inches | 30 Inches |
A blocker beam or additional bumper may not be used to meet the above requirements.
(7) Fenders: All wheels of a motor vehicle must be equipped with fenders designed to cover the entire tire tread width that comes in contact with the road surface. Coverage of the tire tread circumference must be from at least fifteen degrees in front and to at least seventy-five degrees to the rear of the vertical centerline at each wheel measured from the center of the wheel rotation. At no time can the tire come in contact with the body, fender, chassis, or suspension of the vehicle. Street rods and kit vehicles which are more than forty years old and are owned and operated primarily as a collector's item need not be equipped with fenders when the vehicle is used and driven during fair weather on well-maintained, hard-surfaced roads.
(8) Frame: A motor vehicle must be equipped with a frame. If an existing frame from a recognized manufacturer is not used and a special frame is fabricated, it must be constructed of wall box or continuous section tubing, wall channel, or unitized construction capable of supporting the vehicle, its load, and the torque produced by the power source under all conditions of operation. The structural strength of the frame must be certified by the builder as meeting the applicable standards set under 49 C.F.R. 571 Parts 201, 214, 216, and 220 through 224, and the SAE Standards. Such certification must be made by either:
Statutory Authority: RCW 46.37.005 and 46.37.320. 12-03-085, § 204-10-022, filed 1/13/12, effective 2/13/12. Statutory Authority: RCW 46.37.005 and 46.37.240. 09-18-071, § 204-10-022, filed 8/31/09, effective 10/1/09. Statutory Authority: RCW 46.37.005 and 46.37.320. 08-19-079, § 204-10-022, filed 9/16/08, effective 10/17/08.