Utah Administrative Code
Topic - Environmental Quality
Title R307 - Air Quality
Rule R307-361 - Architectural Coatings
Section R307-361-8 - Test Methods

Universal Citation: UT Admin Code R 307-361-8

Current through Bulletin 2024-06, March 15, 2024

(1) Determination of VOC content.

(a) For the purpose of determining compliance with the VOC content limits in Table 1, the VOC content of a coating shall be calculated by following the appropriate formula found in the definitions of VOC actual, VOC content, and VOC regulatory found in R307-361-3.

(b) The VOC content of a tint base shall be determined without colorant that is added after the tint base is manufactured.

(c) If the manufacturer does not recommend thinning, the VOC content shall be calculated for the product as supplied.

(d) If the manufacturer recommends thinning, the VOC content shall be calculated including the maximum amount of thinning solvent recommended by the manufacturer.

(e) If the coating is a multi-component product, the VOC content shall be calculated as mixed or catalyzed.

(f) The coating contains silanes, siloxanes, or other ingredients that generate ethanol or other VOC during the curing process, the VOC content shall include the VOCs emitted during curing.

(2) VOC content of coatings.

(a) To determine the VOC content of a coating, the manufacturer may use EPA Method 24, SCAQMD Method 304-91 (revised February1996), or an alternative method, formulation data, or any other reasonable means for predicting that the coating has been formulated as intended (e.g., quality assurance checks, recordkeeping).

(b) If there are any inconsistencies between the results of EPA Method 24 test and any other means for determining VOC content, the EPA Method 24 test results will govern.

(c) The exempt compounds content shall be determined by ASTM D 3960-05, SCAQMD Method 303-91 (Revised 1993), BAAQMD Method 43 (Revised 1996), or BAAQMD Method 41 (Revised 1995), as applicable.

(3) Methacrylate traffic marking coatings. Analysis of methacrylate multicomponent coatings used as traffic marking coatings shall be conducted according to a modification of EPA Method 24 ( 40 CFR 59, subpart D, Appendix A), which has not been approved for methacrylate multicomponent coatings used for purposes other than as traffic marking coatings or for other classes of multicomponent coatings.

(4) Flame spread index. The flame spread index of a fire-retardant coating shall be determined by ASTM E84-10, "Standard Test Method for Surface Burning Characteristics of Building Materials."

(5) Fire resistance rating. The fire resistance rating of a fire-resistive coating shall be determined by ASTM E119-08, "Standard Test Methods for Fire Tests of Building Construction and Materials."

(6) Gloss determination. The gloss of a coating shall be determined by ASTM D523-89 (1999), "Standard Test Method for Specular Gloss."

(7) Metal content of coatings. The metallic content of a coating shall be determined by SCAQMD Method 318-95, "Determination of Weight Percent Elemental Metal in Coatings by X-Ray Diffraction, SCAQMD Laboratory Methods of Analysis for Enforcement Samples."

(8) Acid content of coatings. The acid content of a coating shall be determined by ASTM D1613-06, "Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer and Related Products."

(9) Drying times. The set-to-touch, dry-hard, dry-to-touch and dry-to-recoat times of a coating shall be determined by ASTM D1640-95 (1999), "Standard Methods for Drying, Curing, or Film Formation of Organic Coatings at Room Temperature," and the tack-free time of a quick-dry enamel coating shall be determined by the Mechanical Test Method of ASTM D1640-95.

(10) Surface chalkiness. The chalkiness of a surface shall be determined by using ASTM D4214-07, "Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films."

(11) Exempt compounds-siloxanes. Exempt compounds that are cyclic, branched, or linear, completely methylated siloxanes, shall be analyzed as exempt compounds by methods referenced in ASTM D 3960-05, "Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings" or by BAAQMD Method 43, "Determination of Volatile Methylsiloxanes in Solvent-Based Coatings, Inks, and Related Materials," BAAQMD Manual of Procedures, Volume III, adopted November 6, 1996.

(12) Exempt compounds-parachlorobenzotrifluoride (PCBTF). The exempt compound PCBTF, shall be analyzed as an exempt compound by methods referenced in ASTM D 3960-05 "Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings" or by BAAQMD Method 41, "Determination of Volatile Organic Compounds in Solvent Based Coatings and Related Materials Containing Parachlorobenzotriflouride," BAAQMD Manual of Procedures, Volume III, adopted December 20, 1955.

(13) Tub and tile refinish coating adhesion. The adhesion of tub and tile coating shall be determined by ASTM D4585-99, "Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation" and ASTM D3359-02, "Standard Test Methods for Measuring Adhesion by Tape Test."

(14) Tub and tile refinish coating hardness. The hardness of tub and tile refinish coating shall be determined by ASTM D3363-05, "Standard Test Method for Film Hardness by Pencil Test."

(15) Tub and tile refinish coating abrasion resistance. Abrasion resistance of tub and tile refinish coating shall be analyzed by ASTM D4060-07, "Standard Test Methods for Abrasion Resistance of Organic Coatings by the Taber Abraser."

(16) Tub and tile refinish coating water resistance. Water resistance of tub and tile refinish coatings shall be determined by ASTM D4585-99, "Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation" and ASTM D714-02e1, "Standard Test Method for Evaluating Degree of Blistering of Paints."

(17) Waterproofing membrane. Waterproofing membrane shall be tested by ASTM C836-06, "Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course."

(18) Reactive penetrating sealer and reactive carbonate stone sealer water repellency. Reactive penetrating sealer and reactive carbonate stone sealer water repellency shall be analyzed by ASTM C67-07, "Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile;" ASTM C97-02, "Standard Test Methods for Absorption and Bulk Specific Gravity of Dimension Stone;" or ASTM C140-06, "Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units."

(19) Reactive penetrating sealer and reactive penetrating carbonate stone sealer water vapor transmission. Reactive penetrating sealer and reactive penetrating carbonate stone sealer water vapor transmission shall be analyzed ASTM E96/E96M-05, "Standard Test Method for Water Vapor Transmission of Materials."

(20) Reactive penetrating sealer -chloride screening applications. Reactive penetrating sealers shall be analyzed by National Cooperative Highway Research Report 244 (1981), "Concrete Sealers for the Protection of Bridge Structures."

(21) Stone consolidants. Stone consolidants shall be tested by using ASTM E2167-01, "Standard Guide for Selection and Use of Stone Consolidants."

(22) Radiation resistance -nuclear coatings. The radiation resistance of a nuclear coating shall be determined by ASTM D 4082-02, "Standard Test Method for Use in Light Water Nuclear Power Plants."

(23) Chemical resistance-nuclear coatings. The chemical resistance of nuclear coatings shall be determined by ASTM D3912-95 (2001), "Standard Test Method for Chemical Resistance of Coatings Used in Light Water Nuclear Power Plants."

Disclaimer: These regulations may not be the most recent version. Utah may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.