Oklahoma Administrative Code
Title 310 - Oklahoma State Department of Health
Chapter 260 - Good Manufacturing Practice Regulations
Subchapter 3 - Manufacturing, Processing, Packing or Holding Human Food
Section 310:260-3-3 - Sanitary operations

Universal Citation: OK Admin Code 310:260-3-3

Current through Vol. 42, No. 1, September 16, 2024

(a) General maintenance. Buildings, fixtures, and other physical facilities of the plant shall be maintained in a sanitary condition and shall be kept in repair sufficient to prevent food from becoming adulterated. Cleaning and sanitizing of utensils and equipment shall be conducted in a manner that protects against allergen cross-contact and against contamination of food, food-contact surfaces, or food-packaging materials.

(b) Cleaning and sanitizing substances. Cleaning compounds and sanitizing agents used in cleaning and sanitizing procedures shall be free from undesirable microorganisms and shall be safe and adequate under the conditions of use. Compliance with this requirement may be verified by any effective means including purchase of these substances under a letter of guarantee or certification, or examination of these substances for contamination. Only the following toxic materials may be used or stored in a plant where food is processed or exposed:

(1) Those required to maintain clean and sanitary conditions;

(2) Those necessary for use in laboratory testing procedures;

(3) Those necessary for plant and equipment maintenance and operation; and

(4) Those necessary for use in the plant's operations.

(c) Storage of toxic materials. Toxic cleaning compounds, sanitizing agents, and pesticide chemicals shall be identified, held, and stored in a manner that protects against contamination of food, food-contact surfaces, or food-packing materials.

(d) Pest control. No pests or animals shall be allowed in any area of a food plant. Guard or guide dogs may be allowed in some areas of a plant if the presence of the dogs is unlikely to result in contamination of food, food-contact surfaces, or food-packing materials. Effective measures shall be taken to exclude pests from the manufacturing, processing, packing, and holding areas and to protect against the contamination of food on the premises by pests. The use of pesticides to control pests in the plant is permitted only under precautions and restrictions that will protect against the contamination of food, food-contact surfaces, and food-packaging materials.

(e) Sanitation of food-contact surfaces. All food-contact surfaces, including utensils and food-contact surfaces of equipment, shall be cleaned as frequently as necessary to protect against contamination of food.

(1) Food-contact surfaces used for manufacturing/processing, packing, or holding low-moisture food shall be in a dry, sanitary condition before use. When the surfaces are wet-cleaned, they shall, when necessary, be sanitized and thoroughly dried before subsequent use.

(2) In wet processing, when cleaning is necessary to protect againstallergen cross-contact or the introduction of microorganisms into food, all food-contact surfaces shall be cleaned and sanitized before use and after any interruption during which the food-contact surfaces may have become contaminated. Where equipment and utensils are used in a continuous production operation, the utensils and food-contact surfaces of the equipment shall be cleaned and sanitized as necessary.

(3) Single-service articles (such as utensils for one-time use, paper cups, and paper towels) should be stored in appropriate containers and shall be handled, dispensed, used, and disposed of in a manner that protectsagainst allergen cross-contact and against contamination of food or food-contact surfaces, or food-packing materials.

(4) Where necessary to prevent the introduction of undesirable microbiological organisms into food products, all utensils and product-contact surfaces of equipment used in the plant shall be cleaned and sanitized prior to such use and following any interruption during which such utensils and contact surfaces may have become contaminated. Where such equipment and utensils are used in a continuous production operation, the contact surfaces of such equipment and utensils shall be cleaned and sanitized on a predetermined schedule using adequate methods for cleaning and sanitizing. Sanitizing agents shall be approved, effective and safe under conditions of use. The wash solution for multi-use beverage containers must contain at least 3% caustic and must be maintained to at least 140 ° F temperature. Any facility, procedure, machine, or device may be acceptable for cleaning and sanitizing equipment and utensils if it is established that such facility, procedure, machine, or device will routinely render equipment and utensils clean and provide adequate sanitizing treatment.

(f) Sanitation of non-food-contact surfaces. Non-food-contact surfaces of equipment used in the operation of a food plant must be cleaned in a manner and as frequently as necessary to protect against allergen cross-contact and against contamination of food, food-contact surfaces, and food-packaging materials.

(g) Storage and handling of cleaned portable equipment and utensils. Cleaned and sanitized portable equipment with food-contact surfaces and utensils should be stored in a location and manner that protects food-contact surfaces from contamination.

Disclaimer: These regulations may not be the most recent version. Oklahoma may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.