New Jersey Administrative Code
Title 7 - ENVIRONMENTAL PROTECTION
Chapter 26A - RECYCLING RULES
Subchapter 3 - APPROVAL OF RECYCLING CENTERS FOR CLASS B, CLASS C OR CLASS D RECYCLABLE MATERIALS
Section 7:26A-3.19 - Additional application requirements for general approval to operate a recycling center for the receipt, storage, processing or transfer of Class D recyclable materials

Universal Citation: NJ Admin Code 7:26A-3.19

Current through Register Vol. 56, No. 18, September 16, 2024

(a) Prior to commencing receipt, storage, processing or transfer of used oil at a recycling center, the owner or operator of the recycling center shall submit to the Department, in addition to the information required pursuant to 7:26A-3.2, the following information:

1. The EPA ID number assigned to the facility;

2. A description of the preparedness and prevention procedures and equipment required by 7:26A-6.7(c)1;

3. A copy of the contingency plan as required by 7:26A-6.7(c) 2;

4. A description of the secondary containment system for containers or tanks to demonstrate compliance with 7:26A-6.7(e)4, 5 or 6, including at least the following:

i. Drawings and a description of the basic design parameters, dimensions and materials of construction of the containment system;

ii. The capacity of the containment system relative to the number and volume of containers or tanks within the system;

iii. A description of how the design promotes drainage or how the containers or tanks are protected from contact with standing liquids in the containment system;

iv. Provisions for preventing or managing accumulated precipitation or run-on; and

v. A description of how accumulated liquids will be analyzed and removed to prevent overflow;

5. A demonstration of compliance with labeling requirements of 7:26A-6.7(e)7;

6. A description of closure procedures and/or copy of the closure plan to demonstrate compliance with 7:26A-6.7(e)9;

7. A copy of an analysis plan as required by 7:26A-6.7(f);

8. A description of the method used to comply with the tracking requirements of 7:26A-6.7(g); and

9. A demonstration of compliance with the residue management requirements in accordance with 7:26A-6.7(j).

(b) Prior to commencing the receipt, storage, processing or transfer of any latex paints, antifreeze, lamps (light bulbs), oil-based paints, batteries, mercury-containing equipment and consumer electronics at a recycling center, the owner or operator of the recycling center shall submit to the Department, in addition to the information required pursuant to 7:26A-3.2, the following information:

1. The EPA ID number assigned to the facility;

2. A description of the preparedness and prevention procedures and equipment required by 7:26A-4.6(b);

3. A copy of the contingency plan as required by 7:26A-4.6(c);

4. A description of the secondary containment system for containers or tanks to demonstrate compliance with 7:26A-4.6(d)1 iii or (d)2ii, including at least the following:

i. Drawings and a description of the basic design parameters, dimensions and materials of construction of the containment system;

ii. The capacity of the containment system relative to the number and volume of containers or tanks within the system;

iii. A description of how the design promotes drainage or how the containers or tanks are protected from contact with standing liquids in the containment system;

iv. Provisions for preventing or managing accumulated precipitation or run-on; and

v. A description of how accumulated liquids will be analyzed and removed to prevent overflow;

5. A description of the design and operation of process buildings to demonstrate compliance with 7:26A-4.6(d)3, if applicable. The description shall include at least the following:

i. Drawings and a description of the basic design parameters, dimensions and materials of construction of the process building;

ii. The design capacity of the building relative to the volume of recyclable materials to be stored or processed within the building; and

iii. A description of the liquid collection and removal system required by 7:26A-4.6(d)3 iii (if applicable), including a discussion of how accumulated liquids will be characterized and removed;

6. A demonstration of compliance with labeling requirements of 7:26A-4.6(e); and

7. A description of closure procedures and/or copy of the closure plan to demonstrate compliance with 7:26A-4.6(g).

Disclaimer: These regulations may not be the most recent version. New Jersey may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.