New Jersey Administrative Code
Title 5 - COMMUNITY AFFAIRS
Chapter 17 - LEAD HAZARD EVALUATION AND ABATEMENT CODE
Subchapter 6 - PAINT REMOVAL; COMPONENT REPLACEMENT; ENCLOSURE; ENCAPSULATION
Section 5:17-6.1 - Lead-based paint removal

Universal Citation: NJ Admin Code 5:17-6.1

Current through Register Vol. 56, No. 18, September 16, 2024

(a) The following paint removal methods are prohibited:

1. Open flame burning or torching:
i. Using cutting torches to remove fire escapes, railings or other metal components coated with lead-based paint is also prohibited unless the paint is first removed four inches out from the area to be cut.

2. The use of heat guns operating above 1,100 degrees Fahrenheit;

3. Machine sanding or grinding without a HEPA-equipped exhaust tool;

4. Uncontained hydroblasting or high pressure washing;

5. Abrasive blasting or sandblasting without a HEPA vacuum-equipped exhaust tool;

6. The use of methylene chloride chemical paint removers; and

7. The use of dry scraping.
i. Exception to (a)7 above: Dry scraping is permitted if the surfaces are near electrical outlets or for scraping accompanying heat gun use. In either case, the area to be dry scraped shall not exceed two square feet.

(b) Heat guns not prohibited by (a)2 above shall not be used for areas exceeding two square feet. In addition to the other worksite preparation requirements of this chapter, the following shall be done prior to heat gun use:

1. A fully-charged ABC 20 pound (minimum) fire extinguisher shall be provided within 100 feet of each work area; and

2. It shall be verified that the existing electrical supply is adequate for the heat gun(s) or portable generators to power the heat gun(s) shall be provided.

(c) The applicable steps listed in (c)1 through 7 below shall be followed for the mechanical paint removal method chosen to abate lead hazards:

1. For use of HEPA sanding with a shroud, the shroud shall be in contact with the surface at all times;

2. For use of a HEPA vacuum power sander, the sandpaper shall be flat on the surface at all times;

3. For HEPA vacuum blasting, the blast head shall remain in contact with the surface at all times. HEPA vacuum blasting shall be used for metal, brick, concrete or other masonry surfaces only;

4. For HEPA vacuum needle gun, the shroud shall remain in contact with the surface at all times. HEPA vacuum needle guns shall be used for metal surfaces only.

5. For wet scraping, all loose and flaking paint shall be removed by working a few square feet at a time. The surface shall be lightly misted, then a paint scraper shall be used to remove loose material which shall be deposited on the plastic sheeting. Scrapers shall be kept razor sharp to minimize abrasion and gouging;

6. For offsite paint removal, building components shall be misted with water prior to removal. Treated components shall remain offsite or wrapped in plastic until any onsite dust-generating activities are concluded and clean up has taken place. Before reinstallation, treated components shall be cleaned utilizing the standard HEPA vacuum/wet wash/HEPA vacuum cycle to remove any residues. Components shall be completely dry and the pH shall be checked prior to repainting; and

7. For on-site paint removal, the chemical paint remover shall be applied following manufacturer's instructions:
i. Softened paint shall be removed using a scraper, putty knife, or wetted steel wool and the material removed shall be deposited in a water-tight and corrosion-proof container.

ii. Alkali neutralization and residue removal shall be performed following manufacturer's instructions or accepted practice;

iii. Following neutralization, all surfaces shall be scrubbed with a high phosphate detergent or its functional equivalent to remove visible residues. An original detergent container and/or the data sheet with information on the use of the product shall be available for inspection at the worksite; and

iv. For wood surfaces or components, the entire neutralization and cleaning process shall take place without allowing the surface to dry.

Disclaimer: These regulations may not be the most recent version. New Jersey may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.