Michigan Administrative Code
Department - Licensing and Regulatory Affairs
Public Service Commission
Technical Standards For Gas Service
Part 4 - ENGINEERING
Section R. 460.2344 - Adoption of standards by reference

Universal Citation: MI Admin Code R. 460.2344

Current through Vol. 25-4, March 15, 2025

Rule 44.

(1) The publications and standards listed in this rule are adopted by reference and are a part of these rules. Publications identified as published by a specific organization are available from the organization at the address specified in this rule. All prices are current at the time of the adoption of these rules. The commission also has copies of the publications available for inspection and distribution at its offices located at 7109 W. Saginaw Highway, Lansing, Michigan 48917 at a cost of 10 cents per page unless otherwise specified in this rule.

(2) The numbers in parentheses following the publications adopted by reference indicate the applicable editions.

(a) The current edition of the Michigan gas safety standards, which is available online at www.michigan.gov/mpsc or may be ordered from the Michigan public service commission. $61.49.

(b) The following publications of the American Gas Association (AGA), available from the American Gas Association, 400 North Capitol Street, NW, Suite 450, Washington, DC 20001, 202-824-7000, www.aga.org:
(i) "Manual for the Determination of Supercompressibility Factors, PRCI Project NX-19," (1970) AGA Catalog No. L00340. $149.00.

(ii) AGA Report No. 8, Part 1, "Thermodynamic Properties of Natural Gas and Related Gases, DETAIL and GROSS Equations of State." (2017) AGA Catalog No. XQ1704-1. $320.00.

(iii) AGA Report No. 3, "Orifice Metering of Natural Gas Part 1: General Equations and Uncertainty Guidelines." (2013, includes errata) AGA Catalog No. XQ1201. $168.00.

(iv) AGA Report No. 3, Part 2, "Orifice Metering of Natural Gas and Other Related Hydrocarbon Fluids - Concentric, Square-edged Orifice Meters, Specifications and Installation Requirements." (2017, includes errata) AGA Catalog No. XQ1601. $168.00.

(v) AGA Report No. 3, "Orifice Metering of Natural Gas Part 3: Natural Gas Applications." (2013) AGA Catalog No. XQ1304. $148.00.

(vi) AGA Report No. 3, "Orifice Metering of Natural Gas Part 4: Background, Development, Implementation Procedures." (1992) AGA Catalog No. XQ9211. $148.00.

(vii) American National Standards Institute (ANSI) B109.1-2019, "Diaphragm-Type Gas Displacement Meters, Under 500 Cubic Feet per Hour Capacity." AGA Catalog No. X61902. $110.00.

(viii) ANSI B109.2-2000 (R2008), "Diaphragm-Type Gas Displacement Meters, 500 Cubic Feet per Hour Capacity and Over." AGA Catalog No. XQ0009. $110.00.

(ix) ANSI B109.3-2019, "Rotary Type Gas Displacement Meters." (2000) AGA Catalog No. XM1901. $110.00.

(x) AGA Report No. 7, "Measurement of Gas by Turbine Meter." (2006) AGA Catalog No. XQ0601. $352.00.

(xi) AGA Report No. 9, "Measurement of Gas by Multigraph Ultrasonic Meters." (2017) AGA Catalog No. XQ1705. $400.00.

(xii) AGA Report No. 11, "Measurement of Natural Gas by Coriolis Meter, Second Edition." (2013) AGA Catalog No. XQ1301. $440.00.

(xiii) National Fuel Gas Code. (2018) AGA Catalog No. Z223118. $60.00.

(c) The following publications of the American Society for Testing and Materials (ASTM) International available from ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428, 610-832-9585, www.astm.org:
(i) ASTM D1826-94, "Standard Test Method for Calorific (Heating) Value of Gases in Natural Gas Range by Continuous Recording Calorimeter." (2017) ASTM Catalog No. D-1826. $46.00.

(ii) ASTM D1945-14, "Standard Test Method for Analysis of Natural Gas by Gas Chromatography." ASTM Catalog No. D-1945. $52.00.

(iii) ASTM D3588-98, "Standard Practice for Calculating Heating Value, Compressibility Factor, and Relative Density of Gaseous Fuels." (2017) ASTM Catalog No. D-3588. $46.00.

(d) The following publications of the American Society for Quality (ASQ) available from American Society for Quality, PO Box 3005, Milwaukee, WI 53201, 800-248-1946, www.asq.org:
(i) ANSI/ASQ Z1.9-2003 (R2018), "Sampling Procedures and Tables for Inspection by Variables for Percent Nonconforming." $149.00.

(ii) ANSI/ASQ Z1.4-2003 (R2018), "Sampling Procedures and Tables for Inspection by Attributes." $159.00.

(e) American Petroleum Institute (API) Standard 1164 Ed. 2 (2009/R2016), "Pipeline SCADA Security," available from API Publishing Services, 1220 L Street, NW, Washington DC 20005. $146.00.

Disclaimer: These regulations may not be the most recent version. Michigan may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.