Code of Massachusetts Regulations
202 CMR - DIVISION OF STANDARDS
Title 202 CMR 2.00 - Massachusetts Standards (advertising And Sale Of Motor Fuel)
Section 2.11 - Standards for the Various Grades of Heating Oils Requiring Manufacturers or Distributors to Furnish Samples of the Same, and Providing for the Entry and Inspection of the Premises of Such Manufacturers or Distributors, and the Inspection of Heating Oils Stored Thereon

Universal Citation: 202 MA Code of Regs 202.2

Current through Register 1531, September 27, 2024

(1) Scope. 202 CMR 2.11 covers grades of heating oil intended for use in various types of fuel-burning equipment under various operating conditions.

(2) General Requirements.

(a) The grades of heating oil specified in 202 CMR 2.11 shall be homogeneous hydrocarbon oils, free from inorganic acid, and free from excessive amounts of solid or fibrous foreign matter likely to make frequent cleaning of strainers necessary.

(b) Grades containing residual oil shall remain homogeneous in normal storage and not separate into light and heavy components.

(3) Detailed Requirements.

(a) The various grades of heating oil shall conform to the requirements shown in 202 CMR 2.11: Table 1.

(b) The statutory regulations of health or environmental agencies will supersede those outlined in 202 CMR 2.11: Table 1 when they are more stringent than as outlined. Higher sulfur may be permitted in accordance with Massachusetts Department of Environmental Protection regulations at 310 CMR 7.21 and 7.22 which provide for exceptions where approved equipment results in lowering the air polluting effect.

(4) Methods of Test .

(a) The detailed requirements enumerated in the minimum standards shall be determined in accordance with the following American Society for Testing and Materials Methods:
1. Flash Point: Pensky-Martens Closed Tester (ASTM D-93)

2. Pour Point: ASTM D-97

3. Water and Sediment:

Grades 1, 2, 4 and 5: ASTM D-1796

Grade 6: ASTM D-95 and ASTM D-473

4. Ash: ASTM D-482

5. Distillation: ASTM D-86

6. Viscosity:

Grades 1 and 2 (Kinematic): ASTM D-445

Grades 4, 5 and 6 (Saybolt): ASTM D-88

7. Gravity: Hydrometer Method - ASTM D-287

8. Corrosion: Copper Strip, ASTM D-l30, 3 hours @ l22F.

9. Sulfur: Any grade may be determined by the following:

Bomb Method - ASTM D-129

Quartz-Tube Method - ASTM D-1551

High Temperature Method - ASTM D-1552

X-Ray Spectrograph Method - ASTM D-2622

In addition, sulfur in Grade 1 may be determined by the

Lamp Method - ASTM D-1266

(b) Every manufacturer or distributor of heating oils shall submit samples of said products when requested by the Director of Standards.

(c) The Director of Standards, or his authorized agent, may enter each place where heating oils are stored or kept for sale and any vehicle used for its conveyance and may inspect said oil or take therefrom samples for analysis. The Director shall cause each sample taken to be analyzed or otherwise satisfactorily tested and shall record and preserve as evidence the results thereof.

Table 1

MINIMUM STANDARDS FOR HEATING OILS

Grade

Flash Point °F

Pour Point °F

Water & Sed. °F

Ash % by wt.

Distillation

10%

90%

Min

Max

Max

Max

Max

Min

Max

1

100

0

trace

420

550

2

115

20

.05

540

640

4

130

20

.50

.10

5

130

1.00

.10

6

150

2.00

Grade

Saybolt Viscosity, sec.

Kinematic Viscosity @100°F

Gravity deg. API

Copper Strip Corrosion

Sulfur %

Universal @100°F

Furol @122°F

Min

Max

Min

Max

Min

Max

Min

Max

Max

1

1.4

2.2

35

No. 3

.5

2

2.0

3.6

30

.5

4

45 (light)

125 (light)

2.5

5

150 (heavy)

300 (heavy)

2.5

6

350

750

300

2.5

Disclaimer: These regulations may not be the most recent version. Massachusetts may have more current or accurate information. We make no warranties or guarantees about the accuracy, completeness, or adequacy of the information contained on this site or the information linked to on the state site. Please check official sources.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.