Louisiana Administrative Code
Title 51 - PUBLIC HEALTH-SANITARY CODE
Part XIV - Plumbing
Chapter 14 - Reference Standards
Section XIV-1403 - Referenced Standards
Current through Register Vol. 50, No. 3, March 20, 2024
A. Products manufactured to those standards which are followed by the word "Listed" are required to be listed regardless of the standards' requirements for listing.
Standard Designation |
Section/Table |
ANSI A21.4-2008*, Cement-Mortar Lining for Ductile-Iron Pipe and Fittings for Water (same as AWWA C104) |
Table 303 |
ANSI A21.10-2008 (R2012)*, Ductile-Iron and Gray-Iron Fittings (same as AWWA C110) |
Table 603 |
ANSI A21.11-2006*, Rubber Gasket Joints for Ductile-Iron Pressure Pipe and Fittings (same as AWWA C111) |
709.G |
ANSI A21.51-2009*, Ductile-Iron Pipe, Centrifugally Cast (same as AWWA C151) |
Table 603 |
ANSI A21.53 -2006*, Ductile-Iron Compact Fittings for Water Service (same as AWWA C153) |
Table 603 |
ANSI A117.1-2003*, Standard for Accessible and Usable Buildings and Facilities |
415.I.1, 415.I.3 |
ANSI A118.10-2008, Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installation |
Table 303, 303.G.7.c |
ANSI B16.32-1992, Cast Copper Alloy Solder Joint Fittings for Sovent Drainage Systems |
Table 703 |
ANSI B16.43-1982, Wrought Copper and Copper Alloy Solder Joint Fittings for Sovent Drainage Systems |
Table 703 |
ANSI B31.1-55, Code for Pressure Piping |
621.D |
ANSI Z4.1-1986 (R2005)*, Sanitation in Places of Employment, Minimum Requirement for |
405.C, Table 411 - Footnote 13 |
ANSI Z21.10.1-2009, Gas Water Heaters, Volume 1, Storage Water Heaters with Input Ratings of 75,000 Btu per Hour or Less (same as CSA 4.1) |
503.B |
ANSI Z21.10.3-2011, Gas Water Heaters Volume III, Storage, with Input Ratings Above 75,000 Btu per Hour, circulating and instantaneous (same as CSA 4.3) |
503.B |
ANSI Z21.22-1999(R2008)*, Relief Valves for Hot Water Supply Systems (same as CSA 4.4M) |
501.F.1, 511.A.2, 511.G |
ANSI Z124.1.2-2005*, Plastic Bathtub and Shower Units |
Table 407, Table 415.I |
ANSI Z124.3-2005*, Plastic Lavatories |
Table 407 |
ANSI Z124.4-2006*, Plastic Water Closet Bowls and Tanks |
Table 407 |
ANSI Z535.1-2006 (R2011), American National Standard for Safety Colors |
607.A |
APSP 2-1999*, Public Spas |
Table 415.K |
APSP 3-1999*, Permanently Installed Residential Spas |
Table 415.K |
APSP 6-1999*, Residential Portable Spas |
Table 415.K |
APSP 16-2011*, Standard Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs (same as ASME A112.19.8) |
415.K.2, 415.O.6 |
ARI 1010-2002, Drinking Fountains and Self-Contained, Mechanically-Refrigerated Drinking-Water Coolers |
415.C.1 |
ASME Boiler and Pressure Vessel Code, Section IX, Welding and Brazing Qualifications, 1998 Edition |
315.D |
ASME A13.1-2007*, Scheme for the Identification of Piping Systems |
607.A.1, 607.A.3, 607.B |
ASME A112.1.2-2004*, Air Gaps in Plumbing Systems |
415.C.1, 415.C.2, 609.A.1, Table 609, 609.C.7, 609.F.2 |
ASME A112.3.1-2007*, Stainless Steel Drainage Systems for Sanitary DWV, Storm, and Vacuum Applications, Above- and Below Ground |
703.C.1, 703.D, Table 703 |
ASME A112.3.4-2000*, Macerating Toilet Systems and Related Components |
Table 407, 729.C |
ASME A112.4.1-2009, Water Heater Relief Valve Drain Tubes |
Table 511 |
ASME A112.6.1M-1997 (R2002)*, Supports for Off-the-Floor Plumbing Fixtures for Public Use (Floor -Affixed) |
Table 303 |
ASME A112.6.2-2000*, Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks |
Table 303 |
ASME A112.6.3-2001*, Floor Drains |
Table 303 |
ASME A112.6.4-2003 (R2008)*, Roof, Deck, and Balcony Drains (dual roof drain assemblies wherein the inlets of both are enclosed in the same strainer are prohibited) |
Table 303 |
ASME A112.14.1-2003 (R2008)*, Backwater Valves |
705.G.2 |
ASME A112.14.3-2000 (R2004)*, Grease Interceptors |
1005.N.1, 1005.N.5.a, 1005.N.6.a |
ASME A112.18.1-2005*, Plumbing Fixture Fittings (same as CSA B125.1) |
Table 407 |
ASME A112.18.2-2011, Plumbing Waste Fittings (Same as CSA B125.2 |
Table 407 |
ASME A112.18.3-2002*, Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings |
Table 407, 609.C.7 |
ASME A112.18.6-2009, Flexible Water Connectors (same as CSA B125.6) |
Table 407, 509.B |
ASME A112.19.1-2008*, Enameled Cast Iron and Enameled Steel Plumbing Fixtures (same as CSA B45.2) |
Table 407, 415.C.1 |
ASME A112.19.2-2008*, Ceramic Plumbing Fixtures (same as CSA B45.1) |
Table 407, 415.C.1 |
ASME A112.19.3-2008*, Stainless Steel Plumbing Fixtures (same as CSA B45.4) |
Table 407 |
ASME A112.19.4M-1994 (R2008)*, Porcelain Enameled Formed Plumbing Fixtures |
Table 407 |
ASME A112.19.5-2011, Trim for Water-Closet Bowls, Tanks and Urinals (same as CSA B45.15) |
Table 407 |
ASME A112.19.6-1995*, Hydraulic Performance Requirements for Water Closets & Urinals |
Table 407 |
ASME A112.19.7-2012, Hydromassage Bathtub Systems (same as CSA B45.10) |
415.O.4, 415.O.5 |
ASME A112.19.8-2007*, Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs (same as APSP 16) |
415.K.2, 415.O.6 |
ASME A112.19.9M-1991 (R2002)*, Non-vitreous Ceramic Plumbing Fixtures |
Table 407 |
ASME A112.19.19-2006, Vitreous China Nonwater Urinals |
Table 407 |
ASME A112.36.2M-1991 (R2002)*, Cleanouts |
Table 303 |
ASME B1.20.1-1983 (R2006)*, Pipe Threads, General Purpose (Inch) |
313.B |
ASME B16.3-2011, Malleable Iron Threaded Fittings, Classes 150 and 300 |
Table 603 |
ASME B16.4-2011, Gray Iron Threaded Fittings, Classes 125 and 250 |
Table 603 |
ASME B16.5-2009, Pipe Flanges and Flanged Fittings |
Table 603 |
ASME B16.12-2009, Cast-Iron Threaded Drainage Fittings |
Table 703 |
ASME B16.15-2011, Cast Bronze Threaded Fittings, Classes 125 and 250 |
Table 603 |
ASME B16.18-2001, Cast Copper Alloy Solder Joint Pressure Fittings |
Table 603 |
ASME B16.22-2001*, Wrought Copper and Copper Alloy Solder Joint Pressure Fittings |
Table 603 |
ASME B16.23-2011, Cast Copper Alloy Solder Joint Drainage Fittings-DWV |
Table 703 |
ASME B16.24-2011, Cast Copper Alloy Pipe Flanges: Class 150. 300, 400, 600, 900, 1500, and 2500 |
Table 603 |
ASME B16.26-2006*, Cast Copper Alloy Fittings for Flared Copper Tubes |
Table 603 |
ASME B 16.29-2007*, Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings-DWV |
Table 703 |
ASME B16.34-2009, Valves-Flanged Threaded, and Welding End |
Table 603 |
ASME B16.45-1998 (R2006)*, Cast Iron Fittings for Sovent Drainage Systems |
1811.E.3 |
ASSE 1001-2008*, Performance Requirements for Atmospheric-Type Vacuum Breakers |
Table 609 |
ASSE 1002-2008*, Anti-Siphon Fill Valves for Water Closet Tanks |
Table 609 |
ASSE 1003-2009*, Performance Requirements for Water Pressure Reducing Valves for Domestic Water Distribution Systems |
611.J.1, 611.J.6 |
ASSE 1010-2004*, Performance Requirements for Water Hammer Arresters |
Table 407, 611.I.1 |
ASSE 1011-2004*, Performance Requirements for Hose Connection Vacuum Breakers |
Table 609 |
ASSE 1012-2009*, Performance Requirements for Backflow Preventers with Intermediate Atmospheric Vent |
Table 609, 609.C.5 |
ASSE 1013-2011*, Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers |
Table 609, 609.C.5 |
ASSE 1014-2005, Performance Requirements for Backflow Prevention Devices for Hand Held Showers |
Table 303 |
ASSE 1015-2011*, Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies |
Table 609 |
ASSE 1016-2011*, Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations |
Table 623, 623.A.1, 623.A.2 |
ASSE 1017-2009*, Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems |
623.A, Table 623 |
ASSE 1018-2001*, Performance Requirements for Trap Seal Primer Valves - Potable Water Supplied |
415.E.4.a, 625.D.1 |
ASSE 1019-2011*, Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining |
Table 303, Table 609 |
ASSE 1020-2004*, Pressure Vacuum Breaker Assembly |
Table 609 |
ASSE 1022-2003*, Backflow Preventers for Beverage Dispensing Equipment |
Table 609 |
ASSE 1035-2008*, Performance Requirements for Laboratory Faucet Backflow Preventers |
Table 303, Table 609 |
ASSE 1037-1990, Performance Requirements for Pressurized Flushing Devices (Flushometers) for Plumbing Fixtures |
Table 303 |
ASSE 1043-1992, Performance Standard for Cast Iron Sovent Sanitary Drainage Systems |
1811.E.3 |
ASSE 1044-2001*, Performance Requirements for Trap Seal Primer Devices, Drainage Types and Electronic Types |
415.E.4 |
ASSE 1047-2011*, Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies |
Table 609 |
ASSE 1048-2011*, Performance Requirements for Double Check Detector Fire Protection Backflow Prevention Assemblies |
Table 609 |
ASSE 1052-2004*, Performance Requirements for Hose Connection Backflow Preventers |
Table 609 |
ASSE 1056-2001*, Performance Requirements for Spill Resistant Vacuum Breakers |
Table 609 |
ASSE 1061-2011*, Performance Requirements for Push-Fit Fittings (for use on PEX tubing complying with ASTM F 876 or F877, type K and L hard drawn and annealed copper tubing complying with ASTM B 88, and CPVC tubing complying with ASTM D 2846) |
Table 603 |
ASSE 1069-2005*, Performance Requirements for Automatic Temperature Control Mixing Valves |
Table 623, 623.A.1 |
ASSE 1070-2004*, Performance Requirements for Water Temperature Limiting Devices |
Table 623, 623.B, 623.C |
ASSE 1072-2007, Performance Requirements for Barrier Type Floor Drain Trap Seal Protection Devices |
415.E.4 |
ASSE Series 5000-2009*, Cross-Connection Control Professional Qualifications Standard |
319.F, Table 609, 609.F |
ASSE 5110-2009, Backflow Prevention Assembly Tester Professional Qualifications Standard (part of ASSE Series 5000, Cross-Connection Control Professional Qualifications Standard) |
609.F.9 |
ASSE 5120-2009, Backflow Prevention Assembly Surveyor Professional Qualifications Standard (part of ASSE Series 5000, Cross-Connection Control Professional Qualifications Standard) |
607.C |
ASSE 5130-2009, Backflow Prevention Assembly Repairer (part of ASSE Series 5000, Cross-Connection Control Professional Qualifications Standard) |
609.F.9 |
ASTM A48/A48M-2003 (R2008), Standard Specification for Gray Iron Castings |
Table 703, 717.G |
ASTM A53/A53M-2012, Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless |
Table 603 |
ASTM A74-2009, Standard Specification for Cast Iron Soil Pipe and Fittings |
303.G.6.a, Table 703 |
ASTM A126-2004 (R2009), Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings |
Table 603, Table 619.D |
ASTM A197/A197M-2000 (R2011), Standard Specification for Cupola Malleable Iron |
Table 603 |
ASTM A2692010, Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service |
Table 603 |
ASTM A312/A312M-2012, Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
Table 603 |
ASTM A377-2003 (R2008)e1, Standard Index of Specifications for Ductile-Iron Pressure Pipe |
Table 603 |
ASTM A518/A518M-1999 (R2008), Standard Specification for Corrosion-Resistant High-Silicon Iron Castings |
Table 703, 703.F |
ASTM A653/ A653M-2011, Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
Table 303 |
ASTM A733-2003 (R2009)e1, Standard Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples |
Table 603 |
ASTM A746-2009, Standard Specification for Ductile Iron Gravity Sewer Pipe |
Table 703 |
ASTM A778-2001 (R2009)e1, Standard Specification for Welded, Unannealed Austenitic Stainless Steel Tubular Products |
Table 603 |
ASTM A865/A865M-2006, Standard Specification for Threaded Couplings, Steel, Black and Zinc-Coated (Galvanized) Welded and Seamless, for Use in Steel Pipe Joints |
Table 603 |
ASTM A888-2011, Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications |
Table 703 |
ASTM B32-2008, Standard Specification for Solder Metal |
Table 303 |
ASTM B42-2010, Standard Specification for Seamless Copper Pipe, Standard Sizes |
Table 603 |
ASTM B43-2009, Standard Specification for Seamless Red Brass Pipe, Standard Sizes |
Table 603 |
ASTM B75/B75M-2011, Standard Specification for Seamless Copper Tube |
Table 603 |
ASTM B88-2009, Standard Specification for Seamless Copper Water Tube |
513.F.1, Table 603, 613.A.1, 619.A.2, 619.B |
ASTM B135-2008a, Standard Specification for Seamless Brass Tube |
Table 603 |
ASTM B135-2010, Standard Specification for Seamless Brass Tube |
Table 603 |
ASTM B152/B152M-2009, Standard Specification for Copper Sheet, Strip, Plate and Rolled Bar |
Table 303 |
ASTM B248-2007, Standard Specification for General Requirements for Wrought Copper and Copper- Alloy Plate, Sheet, Strip, and Rolled Bar |
Table 303 |
ASTM B248M-2007, Standard Specification for General Requirements for Wrought Copper and Copper- Alloy Plate, Sheet, Strip, and Rolled Bar Metric |
Table 303 |
ASTM B251-2010, Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube |
Table 603 |
ASTM B251M-2010, Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube Metric |
Table 603 |
ASTM B302-2007, Standard Specification for Threadless Copper Pipe, Standard Sizes |
Table 603 |
ASTM B306-2009, Standard Specification for Copper Drainage Tube (DWV) |
Table 703 |
ASTM B447-2007, Standard Specification for Welded Copper Tube |
Table 603 |
ASTM B543-2007e1, Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube |
Table 703 |
ASTM B587-2008, Standard Specification for Welded Brass Tube |
Table 603 |
ASTM B687-1999 (R2011), Standard Specification for Brass, Copper, and Chromium-Plated Pipe Nipples |
Table 603 |
ASTM B813-2010, Standard Specification for Liquid and Paste Fluxes for Soldering Applications for Copper and Copper Tube |
Table 303 |
ASTM B828-2002 (R2010), Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings |
Table 303 |
ASTM C4-2004 (R2009), Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile |
Table 703 |
ASTM C14-2011, Standard Specification for Non-Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Approved for storm drain use only) |
Table 703 |
ASTM C76-2011, Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Approved for storm drain use only) |
Table 703 |
ASTM C76M-2011, Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe-Metric (Approved for storm drain use only) |
Table 703 |
ASTM C361-2011, Standard Specification for Reinforced Concrete Low-Head Pressure Pipe (Approved for storm drain use only) |
Table 703 |
ASTM C361M-2008, Standard Specification for Reinforced Concrete Low-Head Pressure Pipe-Metric (Approved for storm drain use only |
Table 703 |
ASTM C412-2011, Standard Specification for Concrete Drain Tile |
Table 703 |
ASTM C412M-2011, Standard Specification for Concrete Drain Tile Metric |
Table 703 |
ASTM C425-2004 (R2009), Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings |
Table 703, 313.E |
ASTM C443-2011, Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets |
Table 303 |
ASTM C443M-2011, Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets Metric |
Table 303 |
ASTM C444-2003 (R2009), Standard Specification for Perforated Concrete Pipe |
Table 703 |
ASTM C444M-2003(2009), Standard Specification for Perforated Concrete Pipe Metric |
Table 703 |
ASTM C478-2012, Standard Specification for Precast Reinforced Concrete Manhole Sections |
Table 703, 717.G |
ASTM C478M-2011, Standard Specification for Precast Reinforced Concrete Manhole Sections Metric |
Table 703, 710.7 |
ASTM C564-2011, Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings |
Table 303, 709.D.3 |
ASTM C700-2011, Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated |
Table 703 |
ASTM C1053-2000 (R2010), Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications |
Table 703, 703.F |
ASTM C1173-2010e1, Standard Specification for Flexible Transition Couplings for Underground Piping Systems |
Table 303 |
ASTM C1277-2011, Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
Table 303 |
ASTM D395-2003 (R2008), Standard Test Methods for Rubber Property-Compression Set. See §711. D of this code |
Table 303 |
ASTM D412-2006ae2, Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers-Tension. See §711. D of this code |
Table 303 |
ASTM D788-2011, Standard Specification for Poly (Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
Table 303 |
ASTM D 789-2007e1, Standard Test Methods for Determination of Solution Viscosities of Polyamide (PA) |
Table 303 |
ASTM D1527-99 (R2005), Standard Specification for Acrylonitrile- Butadiene-Styrene(ABS) Plastic Pipe, Schedules 40 and 80 |
Table 603 |
ASTM D1785-2006, Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
Table 603 |
ASTM D1869-1995 (R2010), Standard Specification for Rubber Rings for Asbestos-Cement Pipe |
Table 303 |
ASTM D2235-2004 (R2011), Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings. Listed |
Table 303 |
ASTM D2239-2012, Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
Table 603 |
ASTM D2241-2009, Standard Specification for Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR-Series). Listed |
Table 603 |
ASTM D2321-2011, Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
Table 303, Table 703 |
ASTM D2466-2006, Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings Schedule 40 |
Table 603 |
ASTM D2467-2006, Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80. Listed |
Table 603 |
ASTM D 2564-2004 (R2009)e1*, Standard Specification for Solvent Cements for Poly(Vinyl Chloride)(PVC) Plastic Piping Systems. Listed |
Table 303 |
ASTM D2657-2007, Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings |
Table 303 |
ASTM D2661-2011, Standard Specification for Acrylonitrile Butadiene-Styrene (ABS) Plastic Drain, Waste and Vent Pipe and Fittings. Listed |
Table 703 |
ASTM D2665-2011, Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings. Listed |
Table 703 |
ASTM D2672-1996a (2009)*, Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
Table 603 |
ASTM D2737-2012e1, Standard Specification for Polyethylene (PE) Plastic Tubing. Listed |
Table 603 |
ASTM D2751-2005, Standard Specification for Acrylonitrile- Butadiene-Styrene (ABS) Sewer Pipe and Fittings |
Table 703 |
ASTM D2774-2012, Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
Table 303 |
ASTM D2846/D2846M-2009be1, Standard Specification for Chlorinated Poly(Vinyl Chloride)(CPVC) Plastic Hot-and Cold-Water Distribution Systems. Listed |
Table 603 |
ASTM D 2855-1996 (R2010), Standard Practice for Making Solvent-Cemented Joints with Poly (Vinyl Chloride)(PVC) Plastic Pipe and Fittings |
Table 303 |
ASTM D3034-2008, Standard Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
Table 703 |
ASTM D-3138-04(2011), Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components |
Table 303, 711.D.4 Note: This is not an all-purpose cement. Only to be utilized for joining an ABS building drain to a PVC building sewer. |
ASTM D3139-1998 (R2011), Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals. See §313. H.2 of this code |
Table 603 |
ASTM D3212-2007*, Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
Table 703 |
ASTM D4068-2009, Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane |
303.G.7, Table 415.I |
ASTM D4551-1996 (2008)e1*, Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane |
303.G.7, Table 415.I |
ASTM D4894-2007, Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
Table 303 |
ASTM D4895-2010, Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
Table 303 |
ASTM F402-2005 (R2012), Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings |
Table 303 |
ASTM F409-2002 (R2008), Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings |
Table 703 |
ASTM F437-2009, Standard Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80. Listed |
Table 603 |
ASTM F438-2009, Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 |
Table 603 |
ASTM F439-2011, Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80. Listed |
Table 603 |
ASTM F441/F 441M-2009, Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80. Listed |
Table 603 |
ASTM F442/F 442M-2009, Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR) |
Table 603 |
ASTM F493-2010, Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride)(CPVC) Plastic Pipe and Fittings |
Table 303 |
ASTM F628-2008, Standard Specification for Acrylonitrile- Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core. Listed. |
Table 703 |
ASTM F 656-2010*, Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings |
Table 303 |
ASTM F876-2010e1, Standard Specification for Crosslinked Polyethylene (PEX) Tubing |
Table 603 |
ASTM F877-2011a, Standard Specification for Crosslinked Polyethylene (PEX) Plastic Hot and Cold-Water Distribution Systems, Listed |
Table 603 |
ASTM F891-2010, Standard Specification for Coextruded Poly(Vinyl Chloride)(PVC) Plastic Pipe with a Cellular Core |
Table 703 |
ASTM F1281-2011, Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe |
Table 603 |
ASTM F1282-2010, Standard Specification for Polyethylene/ Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe |
Table 603 |
ASTM F1290-1998a (R2011), Standard Practice for Electro fusion Joining Polyolefin Pipe and Fittings |
Table 303, 621.E.2 |
ASTM F1412-2009, Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
Table 703, 703.F, 709.C |
ASTM F1488-2009e1, Standard Specification for Coextruded Composite Pipe |
Table 703 |
ASTM F1499-2012, Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
Table 703 |
ASTM F1673-2010, Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
Table 703, 703.F |
ASTM F1807-2011ae1, Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing |
Table 603 |
ASTM F1960-2011e1, Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing |
Table 603 |
ASTM F2159-2011, Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing |
Table 603 |
ASTM F2080-2009, Standard Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe |
Table 603 |
ASTM F2098-2008, Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings |
Table 603 |
ASTM F2389-2010, Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems |
Table 603, 619.B |
ASTM F2618-2009, Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems |
Table 703, 703.F |
ASTM F2620-2011e1, Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
Table 303, 621.E |
AWS B2.2/B2.2M:2010, Specification for Brazing Procedure and Performance Qualification |
315.D |
AWS A5.8/A5.8M-2011, Spec. for Filler Metals for Brazing and Braze Welding |
Table 303 |
AWS A5.9/5.9M-2006*, Specification for Bare Stainless Steel Welding Electrodes and Rods |
Table 303, 621.G |
AWWA C104-2008*, Cement-Mortar Lining for Ductile-Iron Pipe and Fittings for Water (same as ANSI A21.4) |
Table 303 |
AWWA C110-2008 (R2012)*, Ductile-Iron and Gray-Iron Fittings (same as ANSI A21.10) |
Table 603 |
AWWA C111-2006*, Rubber Gasket Joints for Ductile-Iron and Gray-Iron Pressure Pipe and Fittings (same as ANSI A21.11) |
709.G |
AWWA C151-2009*, Ductile-Iron Pipe, Centrifugally Cast (same as ANSI A21.51) |
Table 603 |
AWWA C153-2006*, Ductile-Iron Compact Fittings for Water Service (same as ANSI A21.53) |
Table 603 |
AWWA C203-2009*, Coal-Tar Protective Coatings and Linings for Steel Water Pipelines-Enamel and Tape-Hot-Applied |
Table 303 |
AWWA C509-2009*, Resilient-Seated Gate Valves for Water Service Supply |
Table 619.D |
AWWA C510-2007*, Double Check Valve Backflow Prevention Assembly |
Table 609 |
AWWA C511-2007*, Reduced Pressure Principle Backflow Prevention Assembly |
Table 609 |
AWWA C606-2011*, Grooved and Shouldered Joints |
Table 303 |
AWWA C900-2007*, Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 In. Through 12 In. (100 mm Through 300 mm), for Water Transmission and Distribution |
Table 603 |
CAN/CSA-B64.10-94, Manual for the Selection, Installation, Maintenance, and Field Testing of Backflow Prevention Devices |
Table 609, Table 609.F.5 - Footnote 1, Table 609.F.6 - Footnotes 2 & 3 |
CAN/CSA-B137.2-2009, PVC Injection-Molded Gasketed Fittings for Pressure Applications. Listed |
Table 603 |
CAN/CSA-B 137.5-2009, Cross-Linked Polyethylene (PEX) Tubing Systems for Pressure Applications. Listed |
Table 603 |
CAN/CSA-B181.1-2006, ABS Drain, Waste, and Vent Pipe and Pipe Fittings |
705.G.2 |
CAN/CSA-B 181.2-2006, PVC Drain, Waste, and Vent Pipe and Pipe Fittings |
705.G.2 |
CAN/CSA-B-182.4-2006, Profile PVC Sewer Pipe and Fittings |
Table 703 |
CDA Copper Sovent Single Stack Plumbing System Design Handbook No. 402/0 (For informational purposes only since is alternate designed plumbing governed under Chapter 12 requirements of this code) |
1811.E.3 |
CDA Copper Tube Handbook (For informational purposes only) |
Table 1805.F |
CISPI HS 74-86, Standard Specification for Cast Iron Soil Pipe and Fittings for Hub and Spigot Sanitary and Storm Drain, Waste and Vent Piping Applications |
Table 703 |
CISPI HSN 85, Standard Specification for Neoprene Rubber Gaskets for Hub and Spigot Cast Iron Soil Pipe and Fittings |
Table 303 |
CISPI 301-09, Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications |
Table 703 |
CISPI 310-11, Standard Specification for Coupling for use in connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications |
Table 303, Table 703, 709.E.3 |
CSA 4.1-2009, Gas Water Heaters, Volume 1, Storage Water Heaters with Input Ratings of 75,000 Btu per Hour or Less (same as ANSI Z21.10.1) |
503.B |
CSA 4.3-2011, Gas Water Heaters Volume III, Storage, with Input Ratings Above 75,000 Btu per Hour, circulating and instantaneous (same as ANSI Z21.10.3) |
503.B |
CSA 4.4M-1999(R2008)*, Relief Valves for Hot Water Supply Systems (same as ANSI Z21.22) |
501.F.1, 511.A.2, 511.G |
CSA B45.1-2008, Ceramic Plumbing Fixtures (same as ASME A112.19.2) |
Table 407, 415.C.1 |
CSA B45.2-2008, Enameled Cast Iron and Enameled Steel Plumbing Fixtures (same as ASME A112.19.1) |
Table 407, 415.C.1 |
CSA B45.4-2008, Stainless Steel Plumbing Fixtures (same as ASME A112.19.3) |
Table 407 |
CSA B45.10-2012, Hydromassage Bathtub Systems (same as ASME A112.19.7) |
415.O.4, 415.O.5 |
CSA B45.15-2011, Trim for Water-Closet Bowls, Tanks and Urinals (same as ASME A112.19.5) |
Table 407 |
CSA B125.1-2005, Plumbing Supply Fittings (same as ASME A112.18.1) |
Table 407 |
CSA B125.2-2011, Plumbing Waste Fittings (same as ASME A112.18.2) |
Table 407 |
CSA B125.6-2009, Flexible Water Connectors (same as ASME A112.18.6) |
Table 407, 509.B |
FMRC 1680-89, Couplings Used In Hubless Cast Iron Systems for Drain, Waste or Vent, Sewer, Rainwater or Storm Drain Systems Above and Below Ground, Industrial/Commercial and Residential |
Table 303 |
FS QQ-L-156 (1946), Caulking Lead |
Table 407 |
FS QQ-L-201 F(2) (1965) (R1970), Lead Sheet, [AMD 02 (1970)] |
Table 303 |
FS SS-P-381, Concrete Pipe Pressure Reinforced- Pretention Reinforcement Steel |
Table 703 |
FS WW-P-325(44), Pipe, Bends, Traps, Caps, and Plugs; Lead (for Industrial Pressure, and Soil and Waste Applications) |
Table 703 |
FS WW-P-541 E/GEN(1), (1980), Plumbing Fixtures (General Specifications), [AMD 01 (1990)] |
Table 407 |
IAPMO Z124.5-2006, Plastic Toilet (Water Closet) Seats |
Table 303 |
IAPMO Z124.6-2007, Plastic Sinks |
Table 407 |
MSS SP-72-2010, Ball Valves with Flanged or Butt-Welding Ends for General Service |
Table 609.D |
MSS SP-80-2008, Bronze Gate, Globe, Angle and Check Valves |
Table 609.D |
MSS SP-110-2010, Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved, and Flared Ends |
Table 609.D |
NFPA 70-2010 National Electrical Code |
731.H.2, 1101.G.3 |
NFPA 99-2012, Health Care Facilities Code |
1302, G105 |
NFPA1192-2008, Standard on Recreational Vehicles |
1501.A, 1601.A |
NSF 14-2011*, Plastic Piping System Components and Related Materials |
303.H.5, 313.H.1 |
NSF 24-2010*, Plumbing System Components for Mobile Homes & Recreational Vehicles |
Table 603 |
NSF 42-2010*, Drinking Water Treatment Units-Aesthetic Effects |
Table 303, 627.A |
NSF 50-2011*, Circulation System Components and Related Materials for Swimming Pools, Spas or Hot Tubs |
415.K.1 |
NSF 53-2011*, Drinking Water Treatment Units-Health Effects |
Table 303, 627.A |
NSF 58-2006*, Reverse Osmosis Drinking Table Water Treatment Units |
Table 303, 627.B |
NSF 61-2011*, Drinking Water System Components-Health Effects |
303.F, 335.C, 415.C.1 |
NSF/ANSI 372-2010*, Drinking Water System Components-Lead Content |
303.F, 613.A, 619.A.3 |
PDI-G101-2010, Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing and Installation Data |
1005.N.1, 1005.N.5.a, 1005.N.6.a |
PDI-WH201-2006, Water Hammer Arresters |
611.I.1 |
SBCCI Standard Building Code, 1994 Edition |
203, |
UFL's TREEO's "Backflow Prevention - Theory and Practice", 2nd Edition, 2004 |
319.F |
UL 174-2004, Household Electric Storage Tank Water Heaters |
503.A |
USC's FCCC&HR's "Manual of Cross-Connection Control", Tenth Edition, 2009 |
319.F |
*ANSI designated as an American National Standard
AUTHORITY NOTE: Promulgated in accordance with R.S. 40:4(A)(7) and R.S. 40:5(2)(3)(7)(9)(16)(17)(20).