Authority: IC
22-13-2-2; IC
22-13-2-13; IC
22-13-4-2; IC
22-15-3
Sec. 5.
(a) All plans
and specifications filed with an application for design release shall comply
with this section.
(b) All plans
and specifications and any supporting data shall be sufficiently clear and
complete to show in detail that the proposed work will comply with the rules of
the commission. They shall be in the English language and dimensions shall be
in the English units of measurement (yards, feet, or inches).
(c) One (1) complete set of plans and
specifications required by this section shall be filed for review.
(d) If a design professional is required by
section 8 of this rule, the following requirements are applicable:
(1) The plans and specifications shall be
prepared by a design professional who is competent to design the construction
covered by the application.
(2)
Each page of the plans and the title page of the specifications shall include
the legible signature and seal of:
(A) the
design professional described in subdivision (1); or
(B) a member of the design professional's
technical or professional staff.
(e) Plans and specifications filed under this
section shall include all of the following as applicable:
(1) Plans and specifications shall indicate
the manufacturer's name, office address, and name and address of each
manufacturing facility listed to fabricate the released system.
(2) Dimensioned floor plans, drawn to scale,
with room identification.
(3) Wall
elevations of all exterior walls.
(4) Cross sections and details of walls,
floors, and roof construction showing dimensions and materials.
(5) Structural plans and elevations showing
size and location of all structural members, truss design and frames (where
applicable), connection details, and all stress calculations, if specifically
required, to ensure structural safety.
(6) Details showing how required structural
and fire-resistive integrity are maintained where wall, floor, and ceiling
penetrations are made for items such as electrical, plumbing, and
communications systems.
(7) Room
finish schedule showing finishes for wall, ceiling, and floors in all rooms,
stairways, and corridors.
(8) Door
schedule including the following:
(A)
Materials.
(B) Size.
(C) Thickness.
(D) Hardware.
(E) Fire rating for all doors (if required).
(9) Window schedule
including the following:
(A) Light.
(B) Vent.
(C) Egress.
(D) Safety glazing.
(E) Hardware information, where applicable.
(10) Construction
specifications (may be on design drawings).
(11) Electrical plans, diagrams, and details
of electrical service equipment.
(12) Plumbing plan including the following:
(A) Fixture location.
(B) Risers.
(C) Drains.
(D) Piping isometrics, including sizes and
materials of piping.
(13)
Mechanical plans indicating location and sizes of equipment and sizes and
materials of ducts.
(14) Energy
conservation design criteria, including the following:
(A) Exterior envelope components
materials.
(B) "U" values of the
envelope systems.
(C) "R" values of
insulation materials.
(D) Size and
type of apparatus.
(E) Equipment
and system controls.
(15) Accessibility for persons with a
physical disability, including the following:
(A) Access to the buildings.
(B) Any interior ramps with slope
dimensions.
(C) Restroom layouts
indicating clearances.
(D) Grab
bars.
(E) Door swings.
(F) Door sizes.
(16) Fire protections systems, including the
following:
(A) Automatic
sprinklers.
(B) Fire
pumps.
(C) Detection and alarm
systems.
(D) Emergency
power.
(E) Communication
systems.
(17) Additional
information as may be needed to demonstrate that the proposed construction will
comply with the rules of the commission.
(18) Data plate shall be located near the
main electrical panel. If the industrialized building system or mobile
structure does not contain an electrical panel, then the location shall be
identified on the systems plans.
(f) Plans and specifications may be filed
with the office of the state building commissioner by one (1) of the following
methods:
(1) Plans and specifications may be
bound in a loose-leaf binder, eight and one-half (81/2) inch by eleven
(11) inch format. All documents submitted shall be organized, indexed, and
tabbed. All binders shall bear the manufacturer's name on the front and bound
edge.
(2) Electronic mail (e-mail)
by method of attaching the required documentation. Electronic filings shall be
compatible with the software used by the office of the state building
commissioner. The electronic documentation shall be organized, indexed, and
tabbed.
