Illinois Administrative Code
Title 35 - ENVIRONMENTAL PROTECTION
Part 219 - ORGANIC MATERIAL EMISSION STANDARDS AND LIMITATIONS FOR THE METRO EAST AREA
Subpart F - COATING OPERATIONS
Section 219.207 - Alternative Emission Limitations
Current through Register Vol. 48, No. 38, September 20, 2024
a) Any owner or operator of a coating line subject to Section 219.204, except coating lines subject to Section 219.204(q)(6), may comply with this Section, rather than with Section 219.204, if a capture system and control device are operated at all times the coating line is in operation and the owner or operator demonstrates compliance with subsection (c), (d), (e), (f), (g), (h), (i), (j), (k), (l), (m), or (n) (depending upon the source category) through the applicable coating analysis and capture system and control device efficiency test methods and procedures specified in Section 219.105 and the recordkeeping and reporting requirements specified in Section 219.211(e); and the control device is equipped with the applicable monitoring equipment specified in Section 219.105(d) and the monitoring equipment is installed, calibrated, operated and maintained according to vendor specifications at all times the control device is in use. A capture system and control device, which does not demonstrate compliance with subsection (c), (d), (e), (f), (g), (h), (i), (j), (k), (l), (m), or (n) may be used as an alternative to compliance with Section 219.204 only if the alternative is approved by the Agency and approved by the USEPA as a SIP revision.
b) Alternative Add-On Control Methodologies
c) An owner or operator of a coating line subject to only one of the emission limitations from among Section 219.204(a)(1)(A), (a)(1)(D), (a)(2)(A),(a)(2)(E), (a)(2)(F), (c)(1), (d), (e), (f), or (i) and equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (b)(1) or (b)(2) are met. An owner or operator of a coating line subject to Section 219.204(a)(1)(B), (a)(1)(C), (a)(2)(B), (a)(2)(C), or (a)(2)(D) and equipped with a capture system and control device must not operate the coating line unless the owner or operator demonstrates compliance with such limitation in accordance with the topcoat protocol referenced in Section 219.105(b)(1)(A) or (b)(1)(B), as applicable.
d) An owner or operator of a miscellaneous metal parts and products coating line that applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within Section 219.204(j) (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), and that is equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (b)(1) or (b)(2) are met.
e) An owner or operator of a heavy off-highway vehicle products coating line that applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within Section 219.204(k) (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), and that is equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (b)(1) or (b)(2) are met.
f) An owner or operator of a wood furniture coating line that applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within Section 219.204(l) (e.g., all coatings used on the line are subject to 0.67 kg/l (5.6 lbs/gal)), and that is equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (b)(1) or (b)(2) are met. If compliance is achieved by meeting the requirements in subsection (b)(2), then the provisions in the note to Section 219.204(l) must also be met.
g) An owner or operator of a can coating line equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (g)(1) or (g)(2) are met.
where:
Ed |
= |
Actual VOM emissions for the day in units of kg/day (lbs/day); |
i |
= |
Subscript denoting the specific coating applied; |
n |
= |
Total number of surface coatings as applied in the can coating operation; |
Vi |
= |
Volume of each coating as applied for the day in units of l/day (gal/day) of coating (minus water and any compounds that are specifically exempted from the definition of VOM); |
Ci |
= |
The VOM content of each coating as applied in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds that are specifically exempted from the definition of VOM); and |
Fi |
= |
Fraction, by weight, of VOM emissions from the surface coating, reduced or prevented from being emitted to the ambient air. This is the overall efficiency of the capture system and control device. |
h) An owner or operator of a plastic parts coating line that applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within Section 219.204(m) or (n) (e.g., all coatings used on the line are subject to 0.42 kg/l (3.5 lbs/gal)), and that is equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (b)(1) or (b)(2) are met.
i) Prior to May 1, 2011, an owner or operator of a metal furniture coating line that applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within Section 219.204(g) (e.g., all coatings used on the line are subject to 0.34 kg/l (2.8 lbs/gal)), and that is equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (b)(1) or (b)(2) are met.
j) Prior to May 1, 2011, an owner or operator of a large appliance coating line that applies one or more coatings during the same day, all of which are subject to the same numerical emission limitation within Section 219.204(h) (e.g., all coatings used on the line are subject to 0.34 kg/l (2.8 lbs/gal)), and that is equipped with a capture system and control device must not operate the subject coating line unless the requirements in subsection (b)(1) or (b)(2) are met.
k) On and after May 1, 2011, an owner or operator of a paper coating line, metal furniture coating line, or large appliance coating line that is equipped with a capture system and control device must not operate the subject coating line unless either:
l) An owner or operator of a flat wood paneling coating line that is equipped with a capture system and control device must not operate the subject coating line unless either:
m) On and after May 1, 2011, an owner or operator of a miscellaneous metal parts and products coating line, plastic parts and products coating line, or pleasure craft surface coating line that is equipped with a capture system and control device must not operate the subject coating line unless:
n) An owner or operator of an aerospace facility that is equipped with a capture system and control device must not operate the subject aerospace coating operation unless: