Code of Colorado Regulations
1200 - Department of Agriculture
1202 - Inspection and Consumer Services Division
8 CCR 1202-13 - RULES PERTAINING TO THE ADMINISTRATION AND ENFORCEMENT OF THE CUSTOM PROCESSING OF MEAT ANIMALS ACT
Part 2 - REQUIREMENTS FOR PROCESSING FACILITIES
Current through Register Vol. 47, No. 17, September 10, 2024
2.1. Except as provided in Part 3.1 below, any processing facility licensed under the Act shall comply with all of the requirements in this Part 2.
2.2. The following areas shall have a concrete floor or surface that is sloped and drained into a waste disposal system:
2.3. Any slaughtering or dressing must be done in a room separate from any room where other processing is done; provided, however, slaughtering or dressing may be done in the same room where cutting, wrapping and other processing of meat is done if:
2.4. All floors in any room where processing is done or where meat is held in storage, other than a freezer, must be: drained into a waste disposal system; coved at the wall to prevent meat products, waste from processing, or any liquids from penetrating between any wall and floor, or under any wall; and constructed of and finished with durable, water-resistant materials that are capable of being readily and thoroughly cleaned.
2.5. The walls, ceilings, columns, and other structural parts of any room where processing is done or where meat is held in storage shall be constructed of and finished with durable, water-resistant materials that are capable of being readily and thoroughly cleaned.
2.6. Any doorway through which any meat product is transferred shall be wide enough so that there is no contact between the doorways and the meat product. Doors in such doorways must be constructed of either rust-resistant metal or other materials that are water-resistant, capable of being readily and thoroughly cleaned, and do not flake, chip, or splinter. If made of wood, all surfaces of such doors and all doorjambs must be securely clad with a rust-resistant metal, and be so affixed so as not to provide crevices for dirt or vermin, or be coated with a water-based epoxy coating intended for such use and labelled as approved by the United States Department of Agriculture.
2.7. Any rails used to transport meat product shall be located, and sufficient space shall be provided in all passageways so that meat product does not come into contact with walls, posts, or other structural parts of the processing facility, or with any containers or other things that may be located in the processing facility or transported through it.
2.8. Every processing facility must have a cooler and a freezer for holding or storing meat product under refrigeration.
2.9. All coolers must be large enough, and constructed, maintained and operated so that the meat product is hung or otherwise stored therein without contacting any interior surface of the cooler, and with sufficient space to permit inspection of the meat product. The refrigeration unit for any cooler must deliver sufficient refrigerated air to maintain the cooler at an ambient temperature of no more than 41° F.
2.10. All freezers must be large enough, and constructed, maintained and operated so that refrigerated air adequately flows under and around the meat product held or stored therein to maintain the required level of refrigeration. The refrigeration unit for any freezer must deliver sufficient refrigerated air to maintain the freezer at an ambient temperature consistent with the requirements in § 35-33-103(12), C.R.S.
2.11. All lighting fixtures must use safety shielded light bulbs in all areas where meat product is exposed, and provide ample illumination for all work areas.
2.12. All work table surfaces must be constructed of rust-resistant metal; provided, however, work table surfaces may be constructed of other durable, water-resistant, non-metal materials if they are free of cracks and are capable of being readily and thoroughly cleaned.
2.13. All equipment used in processing, including, but not limited to, saws, tenderizers, and meat grinders, shall be of such material and construction that they can be readily and thoroughly cleaned. Such requirements include, but are not limited to: being capable of disassembly for thorough cleaning; rust-resistant and free from painted surfaces in any area of the equipment that comes into contact with the meat product; supported by rust-resistant metal legs; and movable for cleaning. All pans, trays, and utensils used for processing shall also be constructed of rust-resistant materials that are capable of being readily and thoroughly cleaned.
2.14. The processing facility must be equipped with a wash basin of adequate size for cleaning equipment and utensils. The wash basin must be: constructed of a rust-resistant metal capable of being readily and thoroughly cleaned; and equipped with hot and cold running, potable water delivered through a combination mixing faucet.
2.15. Each room where processing is done shall be equipped with a hand washing facility. The hand washing facility must be equipped with: a sink that is not hand operated; hot and cold running, potable water delivered through a combination mixing faucet; liquid or powdered soap delivered in a wall- or sink-mounted dispenser; an adequate supply of disposable, single-use sanitary towels in a wall-mounted dispenser; and a receptacle for used sanitary towels.
